Axis Communications axis communications dome network camera user manual Access from the Internet

Page 8

AXIS Q6035 PTZ Dome Network Camera

Accessing the Product

Access from the Internet

Once connected, the Axis product is accessible on your local network (LAN). To access the product from the Internet you must configure your network router to allow incoming data traffic to the product. To do this, enable the NAT-traversal feature, which will attempt to automatically configure the router to allow access to the product. This is enabled from Setup > System Options >

Network > TCP/IP Advanced.

For more information, please see NAT traversal (port mapping) for IPv4, on page 44. See also AXIS Internet Dynamic DNS Service at www.axiscam.net For Technical notes on this and other topics, visit the Axis Support web at www.axis.com/techsup

Set the Root Password

To gain access to the Axis product, you must set the password for the default administrator user root. This is done in the Configure Root Password dialog, which appears when the product is accessed for the first time.

To prevent network eavesdropping, the root password can be set via an encrypted HTTPS connection, which requires an HTTPS certificate. HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt traffic between web browsers and servers. The HTTPS certificate ensures encrypted exchange of information.

To set the password via a standard HTTP connection, enter it directly in the first dialog.

To set the password via an encrypted HTTPS connection, follow these steps:

1.Click Create self-signed certificate.

2.Provide the requested information and click OK. The certificate is created and the password can now be set securely. All traffic to and from the product is encrypted from this point on.

3.Enter a password and then re-enter to confirm the spelling. Click OK. The password has now been configured.

Note

•The default administrator user name root is permanent and cannot be deleted.

•If the password for root is lost, the product must be reset to the factory default settings. See Reset to Factory Default Settings, on page 49.

Configure Capture Mode

Capture mode defines the maximum resolution and maximum frame rate available in the Axis product. The capture mode setting also affects the camera’s angle of view; if using a capture mode with a smaller maximum resolution, the angle of view is reduced.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Axis Q6035 PTZ Dome Network Camera Safety About this documentLiability Intellectual Property RightsTable of Contents Axis Q6035 PTZ Dome Network CameraSymptoms, Possible Causes and Remedial Actions Connectors Hardware OverviewHardware Overview For technical specifications, seeColor Indication LED IndicatorsMidspan LED Indicators Accessing the Product Accessing the ProductAccess from a Browser Start a browser Internet Explorer, Firefox, SafariAccess from the Internet Set the Root PasswordConfigure Capture Mode Network TCP/IP AdvancedAxis Media Control viewer toolbar Live ViewControls on the Live View PTZ Controls AMC Audio ControlsAxis Q6035 PTZ Dome Network Camera How to Stream H.264 Media StreamsMedia Streams Axis Media Control AMCAlternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccessing Audio Streams Java applet supports simplex audio with G.711 encodingBasic Setup Setting Up the ProductSetting Up the Product Video and Audio Video and AudioVideo Stream Pixel CounterClick Save to apply the new settings Stream ProfilesImage 264Camera Settings Capture ModeGo to Setup Video & Audio Camera Settings Image AppearanceExposure Settings Image SettingsOverlay Wide Dynamic RangeGo to Video & Audio Overlay Image Privacy MaskOverlay Image Audio Settings Audio ModesAudio Input G711G726 Audio ClipsAudio Output Live View Config Default Viewer for BrowsersLive View Config Viewer Settings Go to Setup Live View ConfigUser Defined Links Output ButtonsAxis Q6035 PTZ Dome Network Camera Preset Positions PTZ Pan Tilt ZoomPTZ Pan Tilt Zoom AutotrackingMax Limits ConfigurationExclude Areas Gatekeeper Guard TourOsdi Zones AdvancedTour Recording LimitsControls Operator Same as administrator but with lower priorityControl Queue Set Up Motion Detection Windows DetectorsDetectors Motion DetectionAudio Detection Motion Detection ParametersApplications ApplicationsEvents EventsSetting Up an Action Rule Convert Event Types to Action RulesPTZ Control Go to Events Action Rules and click AddRecipients SchedulesRecipient Use with action Go to Events Recipients and click AddRecurrences Go to Events Recurrences and click AddRecordings RecordingsRecording List Continuous RecordingAxis Q6035 PTZ Dome Network Camera System Options System OptionsSecurity UsersAudio Support Date & TimeIeee Basic TCP/IP Settings NetworkIPv4 Address Configuration IPv6 Address ConfigurationAdvanced TCP/IP Settings Link-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service Smtp emailStorage UPnPTMRTP/H.264 BonjourPorts & Devices Network SharePorts Go to System Options Storage Click Network ShareMaintenance SupportReset to Factory Default Settings ScriptingFile Upload Plain Config192.168.0.90 Troubleshooting TroubleshootingEmergency Recovery Procedure Checking the FirmwareProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product is accessible locally but not externally Problems with the H.264 formatVideo and image problems, general Setup Video & Audio Camera SettingsNo images displayed on web Overlay image is not displayedProblems uploading files SettingsStorage and disk management problems Browser freezesTechnical Specifications Technical SpecificationsInstallation aid MaintenancePower ConnectorsMulti-Connector Cable sold separately Function Pin Specifications To +40 V DCMax voltage = +40 V DC With the load, for protection against voltage transientsPerformance Considerations Connection diagramDC power input Axis Q6035 PTZ Dome Network Camera M1.8
Top Page Image Contents