Panasonic WV-CW864A operating instructions Camera

Page 14

(2)Proportional Pan-Tilt Speed (PROPO. P/T)

If ON is selected, the pan-tilt speed changes auto- matically corresponding to the zoom ratio. For example, the pan-tilt speed slows down when the camera zooms in. See page 28 for details.

(3)Area Title (AREA TITLE)

Up to 8 area titles can be assigned to specific scenes on the DIRECTION (NESW) menu or by alphanumeric (USER) assignment. The area title is displayed under the camera ID on the monitor screen when the camera turns to a position that has been assigned an area title. See page 28 for details.

(4)Patrol-learn and Patrol Play (PATROL)

A set of manual operations is stored (LEARN), repro- duced (PLAY) or turned inactive (OFF). Patrol opera- tion stops if SEQ, SORT or AUTO PAN is set to AUTO MODE on the SETUP menu. See page 30 for details.

(5)Alarm Input/Output (ALARM IN/OUT)

Alarm input and output are set on a submenu. Preset positions are assigned to ALARM IN 1 to 4. When alarm inputs are supplied via the alarm input connector, the camera turns to the respective posi- tions. Then the camera sends output signals via the alarm output connector or the coaxial cable to the external devices. The B/W mode may be chosen if light is insufficient. CNT-CLS (Contact Closure) 1, 2 and COAX ALM OUT are used for alarm output set- ting. See page 31 for details.

(6)Cleaning (CLEANING)

This is used for refreshing the electric-mechanical contacts built in the camera. Use this function for maintenance when the camera has been directed at a specific spot or panned over a specific range for a long time.

(7)Electronic Zoom (EL-ZOOM)

Up to 10-fold electronic zooming is available besides 22-fold optical zooming.

(8)Preset Alarm (PRESET ALM)

Alarm signals are generated in the following cases if ON is selected.

When a preset positioning sequence is completed while AUTO MODE is set to SEQ.

When a preset positioning sequence is completed while AUTO MODE is set to SORT.

Positioning is completed at the HOME position in the SELF RETURN mode.

Positioning is completed in the ALARM IN mode.

When positioning to the starting point is completed while AUTO MODE is set to AUTO PAN.

When positioning to the starting point is completed while PATROL is set to PLAY.

(9)Image Hold (IMAGE HOLD)

The camera picture remains as a still image on the monitor screen or until the camera reaches the pre- set position. This function is useful for surveillance via a local area network.

(10)Tilt Angle 0 °/5 °

You can select a titling range. If 5 ° is selected, the tilting angle is adjustable up to 5 ° beyond the hori- zontal position.

Camera

(1)Camera Identification (CAMERA ID)

You can use the camera identification to assign a name to the camera. The camera ID consists of up to 16 alphanumeric characters. You can select whether to have the camera ID displayed on the monitor screen or not. See page 34 for the setting.

(2)Light Control (ALC/MANUAL)

You can select a mode for adjusting the lens iris. There are two modes as follows:

ALC: The lens iris is automatically adjusted accord- ing to the brightness of an object.

You can select one of two modes (SUPER-D2 ON or SUPER-D2 OFF) of backlight compensa- tion.

Backlight compensation is available in the ALC mode. It eliminates strong background light which makes the camera picture dark such as a spotlight.

MANUAL: The lens iris is fixed at the value that you have set regardless of the brightness of an object.

ALC Mode with SUPER-D2 ON Super-Dynamic 2 Function (SUPER-D2)

The important object in a scene is usually placed in the center of the monitor’s screen. In the SUPER-D2 mode, photometric weight is given more to the cen- ter of the screen (where the important object is located) than to the edge of the picture (where a bright backlight would most likely to be located).

You can use the SUPER-D2 function if you select ALC. The function eliminates interference by strong background lighting which makes the camera pic- ture dark, such as a spotlight.

See page 35 for the setting.

ALC Mode with SUPER-D2 OFF

In this mode, the picture is divided into 48 areas. If there is a source of brightness that interferes with the clarity of the picture in these masks, correspon- ding areas mask the light to keep the clarity of the picture.

-14-

Image 14
Contents Color Cctv Camera English Version Important Safety Instructions EnglishPage Contents Digital Flip Operation FeaturesPreface Preset Data Uploading or Down Loading PrecautionsCamera Cleaning Consumables Do not install this camera upside downDo not install the camera in places subject to vibrations Self-diagnosis FunctionConstruction Setup Setup MenuAUTO/ON/OFF P WV-CU161C WV-CU550C/CJWV-CU360C/CJ WV-RM70Setup Menu Description Camera Synchronization Sync Shutter Speed ShutterGain Control AGC Important Notices10Special 2 Menu SPECIAL2 Auto Focus AF ModeRS485 Communication 11Self-diagnosis FunctionMenu Display Setting ProceduresSetup Menu Display Submenu DisplayPosition Setting Position SET Preset MenuPreset Menu Display To Set Panning/Tilting PositionsPan Offset To Set the Lens Zoom and Focus PositionsPreset Identification Setting Preset ID To Return to the Preset Setting Menu Light Control Setting ALC/MANUALScene File Setting Scene File Dwell Time Dwell TimeTo Return to the Preset Number Set Menu Deleting Preset PositionsPreset Speed Setting Preset Speed To Return to the Setup MenuAuto Mode Selection Auto Home Position Setting HomeSelf Return Setting Self OFF SEQ Sort Auto PAN PatrolZoom →PUSH SET RET SEQ Sort Patrol Auto Pan Key Setting Auto PAN KEYDigital Flip Setting Digital Flip New Password Password VerificationSpecial 1 Menu Setting Special Privacy Zone Privacy ZoneArea Title Area Title Settings for on NeswProportional Pan/Tilt PROPO. P/T Zoom ratioSetting for on User Area Title EditingPatrol Learn with a Controller Having Patrol Key Patrol-learn and Patrol Play PatrolTo Quit Editing PAN/TILT/ZOOM/FOCUS Iris Shutter AGC Sens UP White BalancePatrol Play with a Controller not Having the Patrol Key Alarm Input/Output Alarm IN/OUTPatrol Play with a Controller Having the Patrol Key Patrol Play with the Auto PAN KeyCNT-CLS 1, 2 Output Cleaning CleaningElectronic Zoom EL-ZOOM Tilt Angle Tilt Angle 0 /5 Preset Alarm Preset ALMImage Hold Image Hold Camera Identification Camera ID Camera SettingTo Display the Camera Setting Menu ALC Mode with SUPER-D2 on Electronic Sensitivity Enhancement Sens UP Shutter Speed Setting ShutterGain Control AGC on LOW/ MID/ HIGH/OFF Line-lock Sync Mode LL Synchronization SyncWhite Balance White BAL Auto-Tracing White Balance Mode ATW1/ ATW2Automatic White Balance Control Mode AWC Motion Detector Motion DET Special 2 Menu SPECIAL2 Auto Focus Setting AF ModeResolution Resolution Auto S Auto M Auto L Manual L Manual M Manual SPIX Sens UP Setting Black and White Mode BW ModeBW Setting Burst BW SettingCamera Resetting Camera Reset PIX OFF Setting PIX OFFTo Restore the Camera Default Position Refresh To Close the SPECIAL2 MenuChanging the Camera Communication Parameters RS485 SetupInitial Camera Communication Parameters Preset Menu Preset ID ALC/MANUAL SUPER-D2 OFF Dwell Time Factory Default SettingMenu Setting CNT-CLS OFF Coax ALM OUTMounting the Camera InstallationPrecautions Ceiling mountMounting the Bracket PreparationsDisassembling the Camera Setting the Switches RS485 Parameter SetupSW1 For Panasonic’s ProtocolUnit Number Number SW2 RS485 SettingMounting the camera How to Assemble the Cable with the Accessory Connector AC Power Supply ConnectionAccessory Connector Information Connect this to 24V AC Class 2 Power SUP- PLY onlyRS485 Connection Alarm in ConnectionsAlarm OUT Connections OUTSystem Connections AGC On LOW/ON MID/ON HIGH/OFF SpecificationsPrevention of Blooming and Smear Accessories Optional AccessoriesAppendix ShortcutsVersion Française Pareil Accessoires Optionnels Mesures DE Précaution Construction ConfigurationAccessoires Préface Caractéristiques DominantesFonctionnement de la bascule numérique PréfaceCaractéristiques Dominantes Ne jamais essayer de démonter cette caméra vidéo Mesures DE PrécautionNettoyage de caméra vidéo Manipuler la caméra vidéo délicatementFonction dauto diagnostic Cette caméra vidéo ne doit pas être installée à l’envers13. Pièces de remplacement Mesure préventive contre lhyperluminosité et le traînageConstruction Configuration Menu de configurationRéglage de position p SW SET RemarquesDescription du menu de configuration Menu spécial Password LockVerrouillage de mot de passe Caméra vidéoVitesse d’obturation Shutter Commande d’éclairage ALC/MANUALMode ALC avec la fonction SUPER-D2 paramétrée sur OFF Contrôle automatique de gain AGCCommunication RS485 Procédure DE Réglage Affichage du menu de configurationSetup Menu Affichage de menuParamétrage de positionnement Menu de préréglageAffichage du menu de préréglage Position SETDécalage de balayage panoramique ZOOM/FOCUSComment effacer une identification préréglée sauvegardée Préréglage d’identification PresetComment saisir une nouvelle identification préréglée ALC/MANUAL Durée de temporisation Dwell TimeRéglage de contrôle de lumière Paramétrage de fichier de scèneSuppression des positions Préréglées Preset SpeedComment retourner au menu de Configuration Paramétrage de la vitesse prérégléeRetour automatique Sélection de mode automatiqueRéglage de position d’origine Position Réglage de retournement Numérique Digital Flip Vérification du mot de passe Nouveau mot de passeZone Paramétrage de menu spécial 1 SpecialZone de confidentialité Privacy Rapport zoom Titre de zone Area TitleZone Number Réglage par on NeswRéglage pour on User Édition de titre de zoneMémorisation de patrouille et lecture de patrouille Patrol Comment quitter l’éditionLecture de patrouille avec la touche Auto PAN Entrée-sortie dalarme AlarmIN/OUT CNT-CLS 1, 2 Sortie Nettoyage CleaningZoom électronique EL-ZOOM Angle dinclinaison Tilt Angle Préréglage d’alarme Preset ALMMaintien dimage Image Hold Camera ID Réglage de la caméra vidéoIdentification de caméra vidéo Mode ALC avec la fonction SUPER-D2 activée Mode ALC avec la fonction SUPER-D2 OFFContrôle automatique de gain Réglage de la vitesse d’obturationShutter AGC on LOW/MID/HIGH/OFFMode de synchronisation de fréquence trame et réseau LL Réglage de synchronisation SyncMode de contrôle automatique de balance des blancs AWC Balance des blancs White BALMotion Detect Détecteur de mouvementMotion DET Menu spécial 2 SPECIAL2 AF ModeRéglage de mise au point automatique Réduction de bruit numérique DNR Résolution ResolutionMode noir et blanc BW Mode Réglage BWComment fermer le menu SPECIAL2 Réglage Burst BWRéglage PIX OFF PIX OFF Configuration de RS485 Paramètres de communication initiaux De la caméra vidéoRéglages par défaut dusine Menu Rubrique RéglageVisière pare-soleil Installation de la caméra vidéoFixation au plafond Mesures de précautionDémontage de la caméra vidéo Installation de la platine de fixationPréparatifs Configuration de paramètre RS485 Positionnement des interrupteursCas du protocole de Panasonic Position de Numéro ’interrupteur ’unité 103 Installation de la caméra vidéo Réglage RS485Branchements Informations relatives aux connecteurs accessoiresComment assembler le câble au connecteur accessoire Connexion dalimentation à courant alternatif de 24Branchement RS485 Branchements AlarmBranchements Alarm OUT RemarqueBranchement DE Système Mesure Préventive Contre L’HYPERLUMINOSITÉ LE Traînage Caractéristiques TechniquesAccessoires Accessoires OptionnelsAnnexe Raccourcis111 N0803-0 3TR001811BAA