Panasonic WV-CW864A Precautions, Camera Cleaning, Preset Data Uploading or Down Loading

Page 7

Camera Cleaning

Even if this function is used, noise may be produced on the monitor screen, or the preset position may deviate in the course of prolonged use.

In such cases, activate the refresh mode on the special 2 menu. (See page 42.)

To use this camera with WJ-SX550C, WJ-SX150 Matrix Switcher, set the auto cleaning function activated on the Matrix Switcher side, then clean WV-CW864A one time a day.

Preset Data Uploading or Down-

loading

To download the preset data from the camera to the controller or upload the downloaded data to the cam- era, set the following functions to OFF.

Downloading or uploading the data may not work nor- mally if these functions are set to ON.

Alarm (see page 31)

Preset alarm (see page 33)

Cleaning (see page 32)

Motion detection (see page 39)

Auto mode (see page 23)

Self return (see page 23)

Aim the camera at a motionless object such as a wall, if possible, to download or upload the preset data.

Note: Take notice of the following when uploading the downloaded data to the camera.

Preset positions may vary. If a preset position has deviated, delete the preset position and set the cor- rect preset position newly.

Uploading of WV-CW864A preset data to other mod- els (e.g. WV-CW864, WV-CS854, WV-CS854A and WV-NS324) may cause an error and failure of the uploading process.

PRECAUTIONS

1.Do not attempt to disassemble the camera.

To prevent electric shock, do not remove screws or covers.

There are no user-serviceable parts inside. Ask a qualified service personnel for servicing.

2.Handle the camera with care.

Do not misuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling or storage.

3.Consult an expert on the load bearing capacity of the installation surface and structure. If the sur- face is not strong enough, the camera may fall down. Refer to the product specifications for weights.

4.Do not install the camera in places where it will be exposed to corrosive gasses, e.g., in chemical plants, seaside, at swimming pools or the like. Otherwise corrosion of the bracket may cause the camera to fall down.

5.Use the fall-prevention wires to reduce the risk of the camera falling down.

Do not detach the fall-prevention wire securing the camera. Otherwise the camera could fall down, causing injury to persons and damage to the cam- era.

6.Do not use strong or abrasive detergents when cleaning the camera body.

Use a dry cloth to clean the camera when it is dirty. When the dirt is hard to remove, use a mild deter- gent and wipe gently. Care should be taken not to scratch the dome cover when wiping it.

Afterwards, wipe off the remaining detergent with a dry cloth.

7.Never aim the camera at the sun.

Whether or not the camera is in use , never aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may be caused.

8.Never aim the camera at strong light sources for an extended period of time.

Alight source such as a spot light causes burn-in on the display screen. Failure to observe this may cause the image to become discolored due to dete- rioration of the color filter in the CCD.

9.Do not aim the camera at the same object for a long time.

Burn-in of an image may be caused on the fluores- cent screen of CRT.

-7-

Image 7
Contents Color Cctv Camera English Version English Important Safety InstructionsPage Contents Preface FeaturesDigital Flip Operation Camera Cleaning PrecautionsPreset Data Uploading or Down Loading Self-diagnosis Function Do not install this camera upside downDo not install the camera in places subject to vibrations ConsumablesConstruction Setup Menu SetupAUTO/ON/OFF P WV-RM70 WV-CU550C/CJWV-CU360C/CJ WV-CU161CSetup Menu Description Camera Important Notices Shutter Speed ShutterGain Control AGC Synchronization Sync11Self-diagnosis Function Auto Focus AF ModeRS485 Communication 10Special 2 Menu SPECIAL2Submenu Display Setting ProceduresSetup Menu Display Menu DisplayTo Set Panning/Tilting Positions Preset MenuPreset Menu Display Position Setting Position SETTo Set the Lens Zoom and Focus Positions Pan OffsetPreset Identification Setting Preset ID Dwell Time Dwell Time Light Control Setting ALC/MANUALScene File Setting Scene File To Return to the Preset Setting MenuTo Return to the Setup Menu Deleting Preset PositionsPreset Speed Setting Preset Speed To Return to the Preset Number Set MenuOFF SEQ Sort Auto PAN Patrol Home Position Setting HomeSelf Return Setting Self Auto Mode Selection AutoZoom →PUSH SET RET Digital Flip Setting Digital Flip Auto Pan Key Setting Auto PAN KEYSEQ Sort Patrol Password Verification New PasswordPrivacy Zone Privacy Zone Special 1 Menu Setting SpecialZoom ratio Settings for on NeswProportional Pan/Tilt PROPO. P/T Area Title Area TitleArea Title Editing Setting for on UserPAN/TILT/ZOOM/FOCUS Iris Shutter AGC Sens UP White Balance Patrol-learn and Patrol Play PatrolTo Quit Editing Patrol Learn with a Controller Having Patrol KeyPatrol Play with the Auto PAN Key Alarm Input/Output Alarm IN/OUTPatrol Play with a Controller Having the Patrol Key Patrol Play with a Controller not Having the Patrol KeyElectronic Zoom EL-ZOOM Cleaning CleaningCNT-CLS 1, 2 Output Image Hold Image Hold Preset Alarm Preset ALMTilt Angle Tilt Angle 0 /5 To Display the Camera Setting Menu Camera SettingCamera Identification Camera ID ALC Mode with SUPER-D2 on Gain Control AGC on LOW/ MID/ HIGH/OFF Shutter Speed Setting ShutterElectronic Sensitivity Enhancement Sens UP Synchronization Sync Line-lock Sync Mode LLAutomatic White Balance Control Mode AWC Auto-Tracing White Balance Mode ATW1/ ATW2White Balance White BAL Motion Detector Motion DET Auto S Auto M Auto L Manual L Manual M Manual S Auto Focus Setting AF ModeResolution Resolution Special 2 Menu SPECIAL2Burst BW Setting Black and White Mode BW ModeBW Setting PIX Sens UP SettingTo Close the SPECIAL2 Menu PIX OFF Setting PIX OFFTo Restore the Camera Default Position Refresh Camera Resetting Camera ResetInitial Camera Communication Parameters RS485 SetupChanging the Camera Communication Parameters CNT-CLS OFF Coax ALM OUT Factory Default SettingMenu Setting Preset Menu Preset ID ALC/MANUAL SUPER-D2 OFF Dwell TimeCeiling mount InstallationPrecautions Mounting the CameraDisassembling the Camera PreparationsMounting the Bracket RS485 Parameter Setup Setting the SwitchesUnit Number For Panasonic’s ProtocolSW1 Number Mounting the camera RS485 SettingSW2 Connect this to 24V AC Class 2 Power SUP- PLY only AC Power Supply ConnectionAccessory Connector Information How to Assemble the Cable with the Accessory ConnectorOUT Alarm in ConnectionsAlarm OUT Connections RS485 ConnectionSystem Connections Prevention of Blooming and Smear SpecificationsAGC On LOW/ON MID/ON HIGH/OFF Optional Accessories AccessoriesShortcuts AppendixVersion Française Pareil Préface Caractéristiques Dominantes Mesures DE Précaution Construction ConfigurationAccessoires Accessoires OptionnelsCaractéristiques Dominantes PréfaceFonctionnement de la bascule numérique Manipuler la caméra vidéo délicatement Mesures DE PrécautionNettoyage de caméra vidéo Ne jamais essayer de démonter cette caméra vidéoMesure préventive contre lhyperluminosité et le traînage Cette caméra vidéo ne doit pas être installée à l’envers13. Pièces de remplacement Fonction dauto diagnosticConstruction Menu de configuration ConfigurationRéglage de position p Remarques SW SETDescription du menu de configuration Caméra vidéo Password LockVerrouillage de mot de passe Menu spécialContrôle automatique de gain AGC Commande d’éclairage ALC/MANUALMode ALC avec la fonction SUPER-D2 paramétrée sur OFF Vitesse d’obturation ShutterCommunication RS485 Affichage de menu Affichage du menu de configurationSetup Menu Procédure DE RéglagePosition SET Menu de préréglageAffichage du menu de préréglage Paramétrage de positionnementZOOM/FOCUS Décalage de balayage panoramiqueComment saisir une nouvelle identification préréglée Préréglage d’identification PresetComment effacer une identification préréglée sauvegardée Paramétrage de fichier de scène Durée de temporisation Dwell TimeRéglage de contrôle de lumière ALC/MANUALParamétrage de la vitesse préréglée Preset SpeedComment retourner au menu de Configuration Suppression des positions PrérégléesRéglage de position d’origine Sélection de mode automatiqueRetour automatique Position Réglage de retournement Numérique Digital Flip Nouveau mot de passe Vérification du mot de passeZone de confidentialité Privacy Paramétrage de menu spécial 1 SpecialZone Réglage par on Nesw Titre de zone Area TitleZone Number Rapport zoomÉdition de titre de zone Réglage pour on UserComment quitter l’édition Mémorisation de patrouille et lecture de patrouille PatrolIN/OUT Entrée-sortie dalarme AlarmLecture de patrouille avec la touche Auto PAN Zoom électronique EL-ZOOM Nettoyage CleaningCNT-CLS 1, 2 Sortie Maintien dimage Image Hold Préréglage d’alarme Preset ALMAngle dinclinaison Tilt Angle Identification de caméra vidéo Réglage de la caméra vidéoCamera ID Mode ALC avec la fonction SUPER-D2 OFF Mode ALC avec la fonction SUPER-D2 activéeAGC on LOW/MID/HIGH/OFF Réglage de la vitesse d’obturationShutter Contrôle automatique de gainRéglage de synchronisation Sync Mode de synchronisation de fréquence trame et réseau LLBalance des blancs White BAL Mode de contrôle automatique de balance des blancs AWCMotion DET Détecteur de mouvementMotion Detect Réglage de mise au point automatique AF ModeMenu spécial 2 SPECIAL2 Réglage BW Résolution ResolutionMode noir et blanc BW Mode Réduction de bruit numérique DNRRéglage PIX OFF PIX OFF Réglage Burst BWComment fermer le menu SPECIAL2 Paramètres de communication initiaux De la caméra vidéo Configuration de RS485Menu Rubrique Réglage Réglages par défaut dusineMesures de précaution Installation de la caméra vidéoFixation au plafond Visière pare-soleilPréparatifs Installation de la platine de fixationDémontage de la caméra vidéo Positionnement des interrupteurs Configuration de paramètre RS485Cas du protocole de Panasonic Position de Numéro ’interrupteur ’unité 103 Réglage RS485 Installation de la caméra vidéoConnexion dalimentation à courant alternatif de 24 Informations relatives aux connecteurs accessoiresComment assembler le câble au connecteur accessoire BranchementsRemarque Branchements AlarmBranchements Alarm OUT Branchement RS485Branchement DE Système Caractéristiques Techniques Mesure Préventive Contre L’HYPERLUMINOSITÉ LE TraînageAccessoires Optionnels AccessoiresRaccourcis Annexe111 N0803-0 3TR001811BAA