Panasonic WV-CW864A Auto Pan Key Setting Auto PAN KEY, Digital Flip Setting Digital Flip

Page 25

(2)Move the cursor to ZOOM, press the CAM (SET) key, move the joystick to settle the ZOOM posi- tion and return to the AUTO PAN menu. The manual zoom operation is not available in the TELE direction beyond the settled zoom position.

 

** ZOOM LIMIT **

ZOOM

 

 

 

 

 

PUSH SET

 

 

 

 

 

 

 

U ZOOM D

 

RET

OFF: Does not limit the manual zoom operation.

Notes:

When the panning, tilting, zooming or focusing in the SEQ, SORT or PATROL mode is controlled manually, the auto mode function should be can- celled.

To activate the auto mode, select the desired auto mode again or set a time for SELF RETURN in the SET UP menu.

When 0S is selected, the camera stops without dwelling and starts.

Auto refreshing may be activated during the patrol play or the auto mode to calibrate the lens position.

Auto Pan Key Setting (AUTO PAN KEY)

This is used for assigning one of the following auto functions to the AUTO key on the controller. Pressing the AUTO key activates the assigned function after this setting.

Move the cursor to AUTO PAN KEY and select an auto function with the joystick.

The factory default setting is AUTO PAN.

** SET UP MENU **

PRESET 1 MAP

HOME POSITION OFF

SELF RETURN OFF

AUTO MODE OFF AUTO PAN KEY AUTO PAN DIGITAL FLIP ON SPECIAL1

CAMERA

RS485 SET UP

PASSWORD LOCK OFF

The mode changes as follows:

SEQ SORT PATROL

AUTO PAN

AUTO PAN: Assigns the auto panning function to the key.

SEQ: assigns the SEQUENCE function to the key.

SORT: assigns the SORT function to the key.

PATROL: assigns the PATROL PLAY function to the key.

Note: AUTO PAN LED on the controller does not light if something other than AUTO PAN is assigned. AUTO PAN does not stop with the AUTO PAN key.

If PASSWORD LOCK is set to ON, you cannot operate AUTO PAN, SEQ, SORT, and PATROL even by pressing the AUTO key.

Digital Flip Setting (DIGITAL FLIP)

Move the cursor to DIGITAL FLIP and select ON or OFF with the joystick.

** SET UP MENU **

PRESET 1 MAP

HOME POSITION OFF

SELF RETURN OFF

AUTO MODE OFF AUTO PAN KEY AUTO PAN DIGITAL FLIP ON SPECIAL1

CAMERA

RS485 SET UP

PASSWORD LOCK OFF

OFF: The tilt range is limited from 0 ° to 90 °.

ON: The digital flip function allows the tilt angle to widen up to 180 °. The image on the monitor screen is flipped horizontally and vertically at the tilt angle of approx. 135 ° (If the camera is installed on a ceiling).

Note: The tilt range narrows from 0 ° to 90 ° if PAN LIMIT is set to ON.

Notes:

Digital flip functions while moving the joystick down- wards. In case of moving the joystick to other direc- tions, it does not function.

When OFF is selected for DIGITAL FLIP, the follow- ing operations are required to move the camera 180 ° vertically.

1)Move the joystick downwards to aim the camera down.

2)Move the joystick to the right or left to rotate the camera 180 ° horizontally.

3)Move the joystick upwards.

To set the preset position directly from WV-CU360 System Controller, it is temporarily required to set both the electronic zoom function and digital flip function to OFF.

Tilt range setting is disabled between 90 ° and 180 °.

-25-

Image 25
Contents Color Cctv Camera English Version English Important Safety InstructionsPage Contents Preface FeaturesDigital Flip Operation Camera Cleaning PrecautionsPreset Data Uploading or Down Loading Do not install the camera in places subject to vibrations Do not install this camera upside downConsumables Self-diagnosis FunctionConstruction Setup Menu SetupAUTO/ON/OFF P WV-CU360C/CJ WV-CU550C/CJWV-CU161C WV-RM70Setup Menu Description Camera Gain Control AGC Shutter Speed ShutterSynchronization Sync Important NoticesRS485 Communication Auto Focus AF Mode10Special 2 Menu SPECIAL2 11Self-diagnosis FunctionSetup Menu Display Setting ProceduresMenu Display Submenu DisplayPreset Menu Display Preset MenuPosition Setting Position SET To Set Panning/Tilting PositionsTo Set the Lens Zoom and Focus Positions Pan OffsetPreset Identification Setting Preset ID Scene File Setting Scene File Light Control Setting ALC/MANUALTo Return to the Preset Setting Menu Dwell Time Dwell TimePreset Speed Setting Preset Speed Deleting Preset PositionsTo Return to the Preset Number Set Menu To Return to the Setup MenuSelf Return Setting Self Home Position Setting HomeAuto Mode Selection Auto OFF SEQ Sort Auto PAN PatrolZoom →PUSH SET RET Digital Flip Setting Digital Flip Auto Pan Key Setting Auto PAN KEYSEQ Sort Patrol Password Verification New PasswordPrivacy Zone Privacy Zone Special 1 Menu Setting SpecialProportional Pan/Tilt PROPO. P/T Settings for on NeswArea Title Area Title Zoom ratioArea Title Editing Setting for on UserTo Quit Editing Patrol-learn and Patrol Play PatrolPatrol Learn with a Controller Having Patrol Key PAN/TILT/ZOOM/FOCUS Iris Shutter AGC Sens UP White BalancePatrol Play with a Controller Having the Patrol Key Alarm Input/Output Alarm IN/OUTPatrol Play with a Controller not Having the Patrol Key Patrol Play with the Auto PAN KeyElectronic Zoom EL-ZOOM Cleaning CleaningCNT-CLS 1, 2 Output Image Hold Image Hold Preset Alarm Preset ALMTilt Angle Tilt Angle 0 /5 To Display the Camera Setting Menu Camera SettingCamera Identification Camera ID ALC Mode with SUPER-D2 on Gain Control AGC on LOW/ MID/ HIGH/OFF Shutter Speed Setting ShutterElectronic Sensitivity Enhancement Sens UP Synchronization Sync Line-lock Sync Mode LLAutomatic White Balance Control Mode AWC Auto-Tracing White Balance Mode ATW1/ ATW2White Balance White BAL Motion Detector Motion DET Resolution Resolution Auto Focus Setting AF ModeSpecial 2 Menu SPECIAL2 Auto S Auto M Auto L Manual L Manual M Manual SBW Setting Black and White Mode BW ModePIX Sens UP Setting Burst BW SettingTo Restore the Camera Default Position Refresh PIX OFF Setting PIX OFFCamera Resetting Camera Reset To Close the SPECIAL2 MenuInitial Camera Communication Parameters RS485 SetupChanging the Camera Communication Parameters Menu Setting Factory Default SettingPreset Menu Preset ID ALC/MANUAL SUPER-D2 OFF Dwell Time CNT-CLS OFF Coax ALM OUTPrecautions InstallationMounting the Camera Ceiling mountDisassembling the Camera PreparationsMounting the Bracket RS485 Parameter Setup Setting the SwitchesUnit Number For Panasonic’s ProtocolSW1 Number Mounting the camera RS485 SettingSW2 Accessory Connector Information AC Power Supply ConnectionHow to Assemble the Cable with the Accessory Connector Connect this to 24V AC Class 2 Power SUP- PLY onlyAlarm OUT Connections Alarm in ConnectionsRS485 Connection OUTSystem Connections Prevention of Blooming and Smear SpecificationsAGC On LOW/ON MID/ON HIGH/OFF Optional Accessories AccessoriesShortcuts AppendixVersion Française Pareil Accessoires Mesures DE Précaution Construction ConfigurationAccessoires Optionnels Préface Caractéristiques DominantesCaractéristiques Dominantes PréfaceFonctionnement de la bascule numérique Nettoyage de caméra vidéo Mesures DE PrécautionNe jamais essayer de démonter cette caméra vidéo Manipuler la caméra vidéo délicatement13. Pièces de remplacement Cette caméra vidéo ne doit pas être installée à l’enversFonction dauto diagnostic Mesure préventive contre lhyperluminosité et le traînageConstruction Menu de configuration ConfigurationRéglage de position p Remarques SW SETDescription du menu de configuration Verrouillage de mot de passe Password LockMenu spécial Caméra vidéoMode ALC avec la fonction SUPER-D2 paramétrée sur OFF Commande d’éclairage ALC/MANUALVitesse d’obturation Shutter Contrôle automatique de gain AGCCommunication RS485 Setup Menu Affichage du menu de configurationProcédure DE Réglage Affichage de menuAffichage du menu de préréglage Menu de préréglageParamétrage de positionnement Position SETZOOM/FOCUS Décalage de balayage panoramiqueComment saisir une nouvelle identification préréglée Préréglage d’identification PresetComment effacer une identification préréglée sauvegardée Réglage de contrôle de lumière Durée de temporisation Dwell TimeALC/MANUAL Paramétrage de fichier de scèneComment retourner au menu de Configuration Preset SpeedSuppression des positions Préréglées Paramétrage de la vitesse prérégléeRéglage de position d’origine Sélection de mode automatiqueRetour automatique Position Réglage de retournement Numérique Digital Flip Nouveau mot de passe Vérification du mot de passeZone de confidentialité Privacy Paramétrage de menu spécial 1 SpecialZone Zone Number Titre de zone Area TitleRapport zoom Réglage par on NeswÉdition de titre de zone Réglage pour on UserComment quitter l’édition Mémorisation de patrouille et lecture de patrouille PatrolIN/OUT Entrée-sortie dalarme AlarmLecture de patrouille avec la touche Auto PAN Zoom électronique EL-ZOOM Nettoyage CleaningCNT-CLS 1, 2 Sortie Maintien dimage Image Hold Préréglage d’alarme Preset ALMAngle dinclinaison Tilt Angle Identification de caméra vidéo Réglage de la caméra vidéoCamera ID Mode ALC avec la fonction SUPER-D2 OFF Mode ALC avec la fonction SUPER-D2 activéeShutter Réglage de la vitesse d’obturationContrôle automatique de gain AGC on LOW/MID/HIGH/OFFRéglage de synchronisation Sync Mode de synchronisation de fréquence trame et réseau LLBalance des blancs White BAL Mode de contrôle automatique de balance des blancs AWCMotion DET Détecteur de mouvementMotion Detect Réglage de mise au point automatique AF ModeMenu spécial 2 SPECIAL2 Mode noir et blanc BW Mode Résolution ResolutionRéduction de bruit numérique DNR Réglage BWRéglage PIX OFF PIX OFF Réglage Burst BWComment fermer le menu SPECIAL2 Paramètres de communication initiaux De la caméra vidéo Configuration de RS485Menu Rubrique Réglage Réglages par défaut dusineFixation au plafond Installation de la caméra vidéoVisière pare-soleil Mesures de précautionPréparatifs Installation de la platine de fixationDémontage de la caméra vidéo Positionnement des interrupteurs Configuration de paramètre RS485Cas du protocole de Panasonic Position de Numéro ’interrupteur ’unité 103 Réglage RS485 Installation de la caméra vidéoComment assembler le câble au connecteur accessoire Informations relatives aux connecteurs accessoiresBranchements Connexion dalimentation à courant alternatif de 24Branchements Alarm OUT Branchements AlarmBranchement RS485 RemarqueBranchement DE Système Caractéristiques Techniques Mesure Préventive Contre L’HYPERLUMINOSITÉ LE TraînageAccessoires Optionnels AccessoiresRaccourcis Annexe111 N0803-0 3TR001811BAA