Panasonic WV-CW864A Alarm Input/Output Alarm IN/OUT, Patrol Play with the Auto PAN Key

Page 31

3.Open the SET UP menu to stop learning.

Notes:

•It is recommended to set PAN LIMIT to ON for patrol-learn. Otherwise PAN LIMIT is invalid in playback.

•If the power fails in the patrol-learn mode, start the patrol-learn function again from the starting point.

•LEARN also stops 1 minute after starting if the memory is full.

•Auto refreshing may be activated in the patrol play mode or the auto mode to calibrate the lens position.

Patrol Play with a Controller Having the PATROL Key

1.Press the PATROL PLAY key. The camera turns to the starting point and reproduces the operations stored in the memory. Iris operation is valid only in the playback mode.

2.Press the PATROL STOP key and PROGRAM key simultaneously to stop playback or press any manu- al operation key (e.g., PAN/TILT/ ZOOM/FOCUS) except the iris keys.

Patrol Play with a Controller not Having the PATROL Key

1.Select patrol play in the setup menu, and then close the menu. The camera turns to the starting point and the operations stored in memory are reproduced. Iris operation is valid only in the playback mode.

2.Open the SET UP menu, or press any of manual operation keys (e.g., PAN/TILT/ ZOOM/FOCUS) except the iris keys to stop playback.

Patrol Play with the AUTO PAN Key

1.If the PATROL PLAY function is assigned to the AUTO PAN key, press the AUTO PAN key to turn the camera back to the starting point and to reproduce the operation data stored in the memory.

2.To stop playback, press the PATROL STOP key or any manual operation key (e.g., PAN/ TILT/ ZOOM/ FOCUS) except the iris keys.

Notes:

•In the patrol play mode, the camera movement may occasionally deviate from the entered routine when the routine includes a move to a preset position. If this happens, re-enter the routine of manual opera- tions for patrol-learn.

•In the patrol play mode, black and white automatic switching does not work.

•In the patrol play mode, when the power of the con- troller is turned on or off, the patrol play stops. In this case, press the PATROL PLAY key again. (If SELF RETURN is set to ON, the patrol play will start again after elapsing the setting return time.)

●Alarm Input/Output (ALARM IN/OUT)

Move the cursor to ALARM IN/OUT, and press the CAM (SET) key. The ALARM IN/OUT submenu appears.

** SPECIAL

1 **

PRIVACY ZONE

OFF

PROPO.P/T

ON

AREA TITLE

ON(USER)

PATROL

STOP

ALARM IN/OUT

 

 

CLEANING

OFF

EL-ZOOM

ON

PRESET ALM

OFF

IMAGE HOLD

OFF

TILT ANGLE

0°

RET

 

 

Note: While the camera is in the AF mode or the lens moves between WIDE and TELE, alarm input may be ignored if several alarm inputs are received in succession.

ALARM IN 1-4

Alarm input signals are supplied from external devices through the ALARM IN connector to turn the camera to a preset position.

1.Move the cursor to ALARM IN 1* and select a preset position or OFF with the joystick, then press the CAM (SET) key.

The factory default setting is OFF.

**

ALARM IN/OUT **

ALARM

IN

1

OFF

 

ALARM

IN

2

OFF

 

ALARM

IN

3

OFF

ALARM

IN

4

OFF

CNT-CLS 1

 

OFF

TIME

OUT

 

100MS

CNT-CLS 2

 

OFF

COAX ALM OUT

OFF

RET

*Set ALARM IN 2, 3 and 4 in the same way as ALARM IN 1.

1POSI, 2 POSI, 3 POSI and 4 POSI: Preset posi- tion. If an alarm input is received, the camera turns to a preset position, and sends an alarm output signal. The position number corresponds to the alarm input number (1-1,2-2,3-3 and 4-4).

B/W: Available for ALARM INPUT 4 only. The cam- era changes its mode from color to black and white if ALARM IN 4 is supplied.

OFF: The camera ignores alarm inputs.

-31-

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Color Cctv Camera English Version English Important Safety InstructionsPage Contents Preface FeaturesDigital Flip Operation Camera Cleaning PrecautionsPreset Data Uploading or Down Loading Self-diagnosis Function Do not install this camera upside downDo not install the camera in places subject to vibrations ConsumablesConstruction Setup Menu SetupAUTO/ON/OFF P WV-RM70 WV-CU550C/CJWV-CU360C/CJ WV-CU161CSetup Menu Description Camera Important Notices Shutter Speed ShutterGain Control AGC Synchronization Sync11Self-diagnosis Function Auto Focus AF ModeRS485 Communication 10Special 2 Menu SPECIAL2Submenu Display Setting ProceduresSetup Menu Display Menu DisplayTo Set Panning/Tilting Positions Preset MenuPreset Menu Display Position Setting Position SETTo Set the Lens Zoom and Focus Positions Pan OffsetPreset Identification Setting Preset ID Dwell Time Dwell Time Light Control Setting ALC/MANUALScene File Setting Scene File To Return to the Preset Setting MenuTo Return to the Setup Menu Deleting Preset PositionsPreset Speed Setting Preset Speed To Return to the Preset Number Set MenuOFF SEQ Sort Auto PAN Patrol Home Position Setting HomeSelf Return Setting Self Auto Mode Selection AutoZoom →PUSH SET RET Digital Flip Setting Digital Flip Auto Pan Key Setting Auto PAN KEYSEQ Sort Patrol Password Verification New PasswordPrivacy Zone Privacy Zone Special 1 Menu Setting SpecialZoom ratio Settings for on NeswProportional Pan/Tilt PROPO. P/T Area Title Area TitleArea Title Editing Setting for on UserPAN/TILT/ZOOM/FOCUS Iris Shutter AGC Sens UP White Balance Patrol-learn and Patrol Play PatrolTo Quit Editing Patrol Learn with a Controller Having Patrol KeyPatrol Play with the Auto PAN Key Alarm Input/Output Alarm IN/OUTPatrol Play with a Controller Having the Patrol Key Patrol Play with a Controller not Having the Patrol KeyElectronic Zoom EL-ZOOM Cleaning CleaningCNT-CLS 1, 2 Output Image Hold Image Hold Preset Alarm Preset ALMTilt Angle Tilt Angle 0 /5 To Display the Camera Setting Menu Camera SettingCamera Identification Camera ID ALC Mode with SUPER-D2 on Gain Control AGC on LOW/ MID/ HIGH/OFF Shutter Speed Setting ShutterElectronic Sensitivity Enhancement Sens UP Synchronization Sync Line-lock Sync Mode LLAutomatic White Balance Control Mode AWC Auto-Tracing White Balance Mode ATW1/ ATW2White Balance White BAL Motion Detector Motion DET Auto S Auto M Auto L Manual L Manual M Manual S Auto Focus Setting AF ModeResolution Resolution Special 2 Menu SPECIAL2Burst BW Setting Black and White Mode BW ModeBW Setting PIX Sens UP SettingTo Close the SPECIAL2 Menu PIX OFF Setting PIX OFFTo Restore the Camera Default Position Refresh Camera Resetting Camera ResetInitial Camera Communication Parameters RS485 SetupChanging the Camera Communication Parameters CNT-CLS OFF Coax ALM OUT Factory Default SettingMenu Setting Preset Menu Preset ID ALC/MANUAL SUPER-D2 OFF Dwell TimeCeiling mount InstallationPrecautions Mounting the CameraDisassembling the Camera PreparationsMounting the Bracket RS485 Parameter Setup Setting the SwitchesUnit Number For Panasonic’s ProtocolSW1 Number Mounting the camera RS485 SettingSW2 Connect this to 24V AC Class 2 Power SUP- PLY only AC Power Supply ConnectionAccessory Connector Information How to Assemble the Cable with the Accessory ConnectorOUT Alarm in ConnectionsAlarm OUT Connections RS485 ConnectionSystem Connections Prevention of Blooming and Smear SpecificationsAGC On LOW/ON MID/ON HIGH/OFF Optional Accessories AccessoriesShortcuts AppendixVersion Française Pareil Préface Caractéristiques Dominantes Mesures DE Précaution Construction ConfigurationAccessoires Accessoires OptionnelsCaractéristiques Dominantes PréfaceFonctionnement de la bascule numérique Manipuler la caméra vidéo délicatement Mesures DE PrécautionNettoyage de caméra vidéo Ne jamais essayer de démonter cette caméra vidéoMesure préventive contre lhyperluminosité et le traînage Cette caméra vidéo ne doit pas être installée à l’envers13. Pièces de remplacement Fonction dauto diagnosticConstruction Menu de configuration ConfigurationRéglage de position p Remarques SW SETDescription du menu de configuration Caméra vidéo Password LockVerrouillage de mot de passe Menu spécialContrôle automatique de gain AGC Commande d’éclairage ALC/MANUALMode ALC avec la fonction SUPER-D2 paramétrée sur OFF Vitesse d’obturation ShutterCommunication RS485 Affichage de menu Affichage du menu de configurationSetup Menu Procédure DE RéglagePosition SET Menu de préréglageAffichage du menu de préréglage Paramétrage de positionnementZOOM/FOCUS Décalage de balayage panoramiqueComment saisir une nouvelle identification préréglée Préréglage d’identification PresetComment effacer une identification préréglée sauvegardée Paramétrage de fichier de scène Durée de temporisation Dwell TimeRéglage de contrôle de lumière ALC/MANUALParamétrage de la vitesse préréglée Preset SpeedComment retourner au menu de Configuration Suppression des positions PrérégléesRéglage de position d’origine Sélection de mode automatiqueRetour automatique Position Réglage de retournement Numérique Digital Flip Nouveau mot de passe Vérification du mot de passeZone de confidentialité Privacy Paramétrage de menu spécial 1 SpecialZone Réglage par on Nesw Titre de zone Area TitleZone Number Rapport zoomÉdition de titre de zone Réglage pour on UserComment quitter l’édition Mémorisation de patrouille et lecture de patrouille PatrolIN/OUT Entrée-sortie dalarme AlarmLecture de patrouille avec la touche Auto PAN Zoom électronique EL-ZOOM Nettoyage CleaningCNT-CLS 1, 2 Sortie Maintien dimage Image Hold Préréglage d’alarme Preset ALMAngle dinclinaison Tilt Angle Identification de caméra vidéo Réglage de la caméra vidéoCamera ID Mode ALC avec la fonction SUPER-D2 OFF Mode ALC avec la fonction SUPER-D2 activéeAGC on LOW/MID/HIGH/OFF Réglage de la vitesse d’obturationShutter Contrôle automatique de gainRéglage de synchronisation Sync Mode de synchronisation de fréquence trame et réseau LLBalance des blancs White BAL Mode de contrôle automatique de balance des blancs AWCMotion DET Détecteur de mouvementMotion Detect Réglage de mise au point automatique AF ModeMenu spécial 2 SPECIAL2 Réglage BW Résolution ResolutionMode noir et blanc BW Mode Réduction de bruit numérique DNRRéglage PIX OFF PIX OFF Réglage Burst BWComment fermer le menu SPECIAL2 Paramètres de communication initiaux De la caméra vidéo Configuration de RS485Menu Rubrique Réglage Réglages par défaut dusineMesures de précaution Installation de la caméra vidéoFixation au plafond Visière pare-soleilPréparatifs Installation de la platine de fixationDémontage de la caméra vidéo Positionnement des interrupteurs Configuration de paramètre RS485Cas du protocole de Panasonic Position de Numéro ’interrupteur ’unité 103 Réglage RS485 Installation de la caméra vidéoConnexion dalimentation à courant alternatif de 24 Informations relatives aux connecteurs accessoiresComment assembler le câble au connecteur accessoire BranchementsRemarque Branchements AlarmBranchements Alarm OUT Branchement RS485Branchement DE Système Caractéristiques Techniques Mesure Préventive Contre L’HYPERLUMINOSITÉ LE TraînageAccessoires Optionnels AccessoiresRaccourcis Annexe111 N0803-0 3TR001811BAA
Top Page Image Contents