Axis Communications 463001 user manual Power Connector, Function Pin Specifications

Page 63

AXIS Q1604-E Network Camera

Technical Specifications

Note

The I/O connector is connected to the housing (fan/heater) on delivery. In the case of a fan or heater error, an input signal will be triggered in the camera. Set up an action rule in the camera to configure which action the signal shall trigger. For information about events and action rules, see Events, on page 37.

Function

Pin

Notes

Specifications

0 V DC (-)

1

0 V DC

DC output

2

Can be used to power auxiliary equipment.

3.3 V DC

Note: This pin can only be used as power out.

Max load = 50 mA

Digital Input

3

Connect to pin 1 to activate, or leave floating (unconnected)

0 to max 40 V DC

to deactivate

Digital Output

4

Connected to pin 1 when activated, floating (unconnected)

0 to max 40 V DC, open drain,

when deactivated. If used with an inductive load, e.g. a relay,

100 mA

a diode must be connected in parallel with the load, for

protection against voltage transients.

Power Connector

2-pin terminal block for power input.	DC power input
Use a Safety Extra Low Voltage (SELV)
compliant limited power source (LPS)
with either a rated output power
limited to ≤100 W or a rated output
current limited to ≤5 A.

63

Image 63

Contents Axis Q1604-E Network Camera Intellectual Property Rights About this documentLegal Considerations LiabilityLearn More SupportAxis Q1604-E Network Camera Table of ContentsTechnical Specifications Hardware Overview Hardware OverviewAxis Q1604-E Network Camera Axis Q1604-E Network Camera Connectors and Buttons Cold Startup Delay SwitchControl Button LED IndicatorsLED indicators in camera SD Card SlotReplacing the lens Hardware Overview Status LED Behavior for Focus AssistantAccessing the Product Accessing the ProductAccess from a Browser Accessing the Product Access from the Internet Set the Root PasswordClick Use Https Manual Trigger Configure Capture ModeLive View Controls on the Live ViewGo to Setup Events Axis Media Control viewer toolbarAMC Audio Controls Axis Media Control AMC How to Stream H.264Media Streams Media StreamsAlternative Methods of Accessing the Video Stream Accessing Audio Streams Adjust Focus Setting Up the ProductSetting Up the Product Basic SetupSetting Up the Product Focus Assistant Pixel Counter Video and AudioVideo and Audio Video Stream264 ImageStream Profiles Camera SettingsCapture Mode Go to Setup Video & Audio Camera SettingsWide Dynamic Range Exposure SettingsImage Appearance White BalanceIR cut filter OverlayShutter & Gain Set Shutter toPrivacy Mask Overlay ImageGo to Video & Audio Overlay Image Video and Audio Audio Settings Audio ModesAudio Input Audio Output Audio ClipsLive View Config Live View ConfigDefault Viewer for Browsers Output Buttons Viewer SettingsGo to Setup Live View Config User Defined LinksFor more information about I/O ports, see I/O Ports, on Motion Detection DetectorsDetectors Camera TamperingMotion Detection Parameters Set Up Motion Detection WindowsRecommended values Default valuesAudio Detection Low level 0%Application Licenses Install ApplicationApplications ApplicationsAxis Q1604-E Network Camera Events EventsGo to Events Action Rules and click Add Setting Up an Action RuleGo to Events Recipients and click Add Setting Up an Email RecipientEvents Recipients Recipient Use with actionGo to Events Recurrences and click Add SchedulesRecurrences Go to Events Schedules and click AddContinuous Recording RecordingsRecordings Recording ListLanguages LanguagesUsers System OptionsSystem Options SecurityIeee CertificatesGo to System Options Security Ieee Go to Setup System Options Security Certificates Date & TimeAudio Support System Options Network Basic TCP/IP SettingsAxis Video Hosting System Avhs Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationNAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Go to System Options Storage and click SD Card System Options StorageSD Card Network SharePort Status MaintenancePorts & Devices PortsAdvanced System Options SupportReset to Factory Default Settings Plain ConfigFile Upload Checking the Firmware TroubleshootingTroubleshooting Emergency Recovery ProcedureSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externally Problems with streaming H.264Basic Settings Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Setup Video & Audio Camera SettingsStorage disruption Storage and disk management problemsTechnical Specifications Technical SpecificationsInput/output Audio input Function/group Specifications Audio Audio streamingAlarm actions Installation aidsConnectors Function Pin Specifications Audio Input Audio Output Performance ConsiderationsM5.3