Samsung SCC-C7453N user manual Installation

Page 13

Installation

1.Press the SNAP FIT of the ADAPTOR in the HOUSING to open the ADAPTOR part, and then insert all external cables into the HOUSING. Secure the HOUSING on the PIPE or MOUNT by turning it clockwise.

(Secure two components tightly, to avoid loosened HOUSING.)

PIPE OR	PIPE OR
MOUNT	MOUNT
HOUSING	HOUSING

EXTERNAL

CABLE

ADAPTOR

SNAP-FIT

2.Connect external cables to the CONNECTORS(ALARM IN, POWER, RS-485, ALARM OUT) and connect the CONNECTOR to the ADAPTOR.

Insert the cable into the FRAME SET, and close the ADAPTOR.

English

	BNC JACK
	HOUSING
	INSULATION
POWER INPUT ALARM OUT	TUBE
POWER INPUT ALARM OUT

ALARM IN

M 

RS-485 EXTERNAL

CABLE

ADAPTOR

Then, wrap the BNC JACK with the INSULATION TUBE, and use an insulation tape to seal up the end of the INSULATION TUBE so that the BNC JACK does not protrude outside of the INSULATION TUBE coating.

For more information about cable connection, refer to Connecting the adaptor cable. (page 21)

English _13

00956B-NA_SCC-C7453N-ENG.indb 13

2009-08-13 오후 10:58:

Image 13

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents What’s Included FeaturesCamera At a GlanceFrame SET Optional Accessories for Installation Installation & connectionEnglish Housing PrecautionsPreparation CableInstallation Housing Mount Power BNC Cable Bush 24V CablePIN Bush BushHousing Camera Screws Cover Dome Gasket Dome 22P Connector Housing RackFrame SET Hook Protective Camera Tape CoverCamera Address Setup Initial SetupCommunication Protocol Setup Samsung Half Samsung FullSetting RS-422A/RS-485 Termination Baud Rate SetupUse pins #5, #6 of SW603 to set the baud rate Factory default is 9600 BPSSame address in the network RS-422A/RS-485 Full Duplex OrganizationConnecting to a monitor Connecting with Other deviceMonitor Alarm Alarm OUT CONTROLLER/DVR Power SourceTo connect Alarm OUT To connect AlarmTo connect the controller Power Supply Connecting the adaptor cableAdaptor Board Using OSD icons How to use the keyboard controllerCamera will resume the last run operation Main Menu Profile Night DAY ModeBurst EXT BurstCamera SET You can configure the general settings of the camera moduleCamera ID  Location Specify the display position of the camera IDWith this, you can adjust the AGC level of a  Manual Adjust the iris level manuallyIris AGCDNR MotionShutter SENS-UPFlickerless You can specify a recording mode according to the sceneXDR DAY/NIGHTNeeded Auto Switch or Auto FocusSET-AUTO SET are not available White BAL DAY/NIGHT Display Zoom Zoom SpeedDisplay P/T Digital ZoomAGC Color SUP SyncReverse POSI/NEGAWhen multiple motions continue arbitrarily You can enable the motion detection and tracking functionsIntelligent Video AdvancedAlarm OUT ResolutionPrivacy Zone DisplayPreset Select Position and adjust PAN Select the preset numberSettings so define them again after the operation Auto Pan SetupAuto SET You can set the Auto PAN, PATTERN, and Auto PlayPosition Direction Left Endless OFF Speed Scan Setup Pattern SetupSelect the Start and move the camera using pan/tilt/zoom ~ 511 for Preset Auto Play SetupYou can set the north direction and the zone coverage Zone SETSelect Main MENU-ZONE SET Select Main MENU-ALARM SET Alarm SET Auto SET Sets the pattern and scan Other SET Clock SETPassword Factory DefaultsOSD Color Proportional P/TSystem Info CommunicationYou can check the system information Select Main MENU-SYSTEM InfoYou can set the language of the user interface LanguageFunction Key Shortcut KeysSmart Dome Camera SpecificationsINT/LINE Lock Tilt PANProduct Appearance 00956B-NASCC-C7453N-ENG.indb 2009-08-13 오후