Samsung SCC-C7453N user manual Needed, SET-AUTO SET are not available, Auto Switch or Auto Focus

Page 30

setup

-NIGHTDAY DWELL TIME : Time required to determine the filter switch.

-MASK AREA : If there exists a bright

spot light source in a night scene, you MASK AREA

can specify the size and position as	<SIZE>
needed.	<LOCATION>
This will prevent an error in switching
filter, or failure to determine the filter
switch in a night scene where a bright
spot light source exists.
Any excessively bright area in a night
scene will be MASKed.

You can specify MASK 1 and 2 simultaneously.

If <BACKLIGHT> is set to <BLC>, the MASK AREA function is not available.

EXT : The interface to an external alarm enables an automatic switch between DAY and NIGHT mode.

If you set <DAY/NIGHT> to EXT, and alarm #1 to NO/NC in ALARM SET- ALARM IN SET, the alarm can be used for an input signal in EXT mode of <DAY/NIGHT>.

If an alarm signal occurs, the mode will switch to NIGHT.

M 	If <DAY/NIGHT> is set to EXT, ALARM1 in ALARM OUT SET, and ALARM1 in ALARM
	SET-AUTO SET are not available.
	If you use an infrared light source while in AUTO mode, this may cause a failure in
	AUTO SWITCH or AUTO FOCUS.

30_ setup

00956B-NA_SCC-C7453N-ENG.indb 30

2009-08-13 오후 10:58:

Image 30

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents Features What’s IncludedAt a Glance CameraFrame SET Installation & connection Optional Accessories for InstallationEnglish Preparation PrecautionsHousing CableInstallation PIN Bush Power BNC Cable Bush 24V CableHousing Mount BushFrame SET 22P Connector Housing RackHousing Camera Screws Cover Dome Gasket Dome Hook Protective Camera Tape CoverCommunication Protocol Setup Initial SetupCamera Address Setup Samsung Half Samsung FullUse pins #5, #6 of SW603 to set the baud rate Baud Rate SetupSetting RS-422A/RS-485 Termination Factory default is 9600 BPSRS-422A/RS-485 Full Duplex Organization Same address in the networkMonitor Alarm Alarm OUT Connecting with Other deviceConnecting to a monitor CONTROLLER/DVR Power SourceTo connect Alarm To connect Alarm OUTTo connect the controller Connecting the adaptor cable Power SupplyAdaptor Board How to use the keyboard controller Using OSD iconsCamera will resume the last run operation Main Menu Profile Burst DAY ModeNight EXT BurstCamera ID You can configure the general settings of the camera moduleCamera SET  Location Specify the display position of the camera IDIris  Manual Adjust the iris level manuallyWith this, you can adjust the AGC level of a AGCShutter MotionDNR SENS-UPXDR You can specify a recording mode according to the sceneFlickerless DAY/NIGHTAuto Switch or Auto Focus NeededSET-AUTO SET are not available White BAL DAY/NIGHT Display P/T Zoom SpeedDisplay Zoom Digital ZoomReverse SyncAGC Color SUP POSI/NEGAIntelligent Video You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily AdvancedPrivacy Zone ResolutionAlarm OUT DisplayPreset Select the preset number Select Position and adjust PANAuto SET Auto Pan SetupSettings so define them again after the operation You can set the Auto PAN, PATTERN, and Auto PlayPosition Direction Left Endless OFF Speed Pattern Setup Scan SetupSelect the Start and move the camera using pan/tilt/zoom Auto Play Setup ~ 511 for PresetZone SET You can set the north direction and the zone coverageSelect Main MENU-ZONE SET Alarm SET Select Main MENU-ALARM SET Auto SET Sets the pattern and scan Clock SET Other SETOSD Color Factory DefaultsPassword Proportional P/TYou can check the system information CommunicationSystem Info Select Main MENU-SYSTEM InfoLanguage You can set the language of the user interfaceShortcut Keys Function KeySpecifications Smart Dome CameraINT/LINE Lock PAN TiltProduct Appearance 00956B-NASCC-C7453N-ENG.indb 2009-08-13 오후