Samsung SCC-C7453N user manual Zone SET, You can set the north direction and the zone coverage

Page 43

ZONE SET

You can set the north direction and the zone coverage.

For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 22)

1. Select <MAIN MENU>-<ZONE SET>.

 MAIN MENU 

PROFILE

CAMERA SET

INTELLIGENCE

PRIVACY ZONE

PRESET

AUTO SET

ZONE SET

ALARM SET

CLOCK SET

OTHER SET

English

2.Set <AZIMUTH> to <ON>.

3.Set the north direction using the joystick and press [ENTER].

SET NORTH : In SET NORTH, press [ENTER] to set the north direction which will be the reference for all other directions.

4.Set <ZONE AREA SET> to <ON>.

ZONE SET 

AZIMUTH	OFF
ZONE AREA SET	OFF

5.When the <ZONE AREA MAP> screen appears, select a number.

6.When the <ZONE AREA SET> screen appears, set the <POSITION> and <ZONE ID SET>.

For entering the name, refer to “CAMERA ID”. (page 26)

POSITION : Sets the left/right boundaries of the zone.

ZONE AREA MAP

1 2 3 4

5 6 7 8

English _43

00956B-NA_SCC-C7453N-ENG.indb 43

2009-08-13 오후 10:58:

Image 43

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents What’s Included FeaturesCamera At a GlanceFrame SET Optional Accessories for Installation Installation & connectionEnglish Cable PrecautionsHousing PreparationInstallation Bush Power BNC Cable Bush 24V CableHousing Mount PIN BushHook Protective Camera Tape Cover 22P Connector Housing RackHousing Camera Screws Cover Dome Gasket Dome Frame SETSamsung Half Samsung Full Initial SetupCamera Address Setup Communication Protocol SetupFactory default is 9600 BPS Baud Rate SetupSetting RS-422A/RS-485 Termination Use pins #5, #6 of SW603 to set the baud rateSame address in the network RS-422A/RS-485 Full Duplex OrganizationCONTROLLER/DVR Power Source Connecting with Other deviceConnecting to a monitor Monitor Alarm Alarm OUTTo connect Alarm OUT To connect AlarmTo connect the controller Power Supply Connecting the adaptor cableAdaptor Board Using OSD icons How to use the keyboard controllerCamera will resume the last run operation Main Menu Profile EXT Burst DAY ModeNight Burst Location Specify the display position of the camera ID You can configure the general settings of the camera moduleCamera SET Camera IDAGC  Manual Adjust the iris level manuallyWith this, you can adjust the AGC level of a IrisSENS-UP MotionDNR ShutterDAY/NIGHT You can specify a recording mode according to the sceneFlickerless XDRNeeded Auto Switch or Auto FocusSET-AUTO SET are not available White BAL DAY/NIGHT Digital Zoom Zoom SpeedDisplay Zoom Display P/TPOSI/NEGA SyncAGC Color SUP ReverseAdvanced You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily Intelligent VideoDisplay ResolutionAlarm OUT Privacy ZonePreset Select Position and adjust PAN Select the preset numberYou can set the Auto PAN, PATTERN, and Auto Play Auto Pan SetupSettings so define them again after the operation Auto SETPosition Direction Left Endless OFF Speed Scan Setup Pattern SetupSelect the Start and move the camera using pan/tilt/zoom ~ 511 for Preset Auto Play SetupYou can set the north direction and the zone coverage Zone SETSelect Main MENU-ZONE SET Select Main MENU-ALARM SET Alarm SET Auto SET Sets the pattern and scan Other SET Clock SETProportional P/T Factory DefaultsPassword OSD ColorSelect Main MENU-SYSTEM Info CommunicationSystem Info You can check the system informationYou can set the language of the user interface LanguageFunction Key Shortcut KeysSmart Dome Camera SpecificationsINT/LINE Lock Tilt PANProduct Appearance 00956B-NASCC-C7453N-ENG.indb 2009-08-13 오후