Samsung SCC-C7453N user manual Communication, System Info, You can check the system information

Page 48

setup

COMMUNICATION

You can set the RS-485 communications setting in regard of the camera.

For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 22)

1.Select <MAIN MENU>-<COMMUNICATION>.

2.Select each item and set appropriately.

PRIORITY : Set the priority by selecting <HW> or <SW>.

When selected <HW>, the protocol, baud rate and address settings will follow those settings of the adaptor switch.

PROTOCOL, BAUD RATE, ADDRESS : When selected <SW>, you can manually set the protocol, baud rate and address.

COMMUNICATION 

RS485
PRIORITY	HW
PROTOCOL	SAMSUNG
	HALF
BAUD RATE	9600
ADDRESS	0

SYSTEM INFO

You can check the system information.

For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 22)

1.Select <MAIN MENU>-<SYSTEM INFO>.

2.The current system information is displayed.

SYSTEM INFO 

TYPE	4_PTZ_NOR_N
PROTOCOL	SAMSUNG
ADDRESS	0
COMM. TYPE	HW, RS485, HALF
BAUD RATE	9600
SERIAL NO.	000000000000000
CAMERA VER.	v1.00_00000
ALARM VER.	v1.00_00000

48_ setup

00956B-NA_SCC-C7453N-ENG.indb 48

2009-08-13 오후 10:58:

Image 48

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents Features What’s IncludedAt a Glance CameraFrame SET Installation & connection Optional Accessories for InstallationEnglish Precautions HousingPreparation CableInstallation Power BNC Cable Bush 24V Cable Housing MountPIN Bush Bush22P Connector Housing Rack Housing Camera Screws Cover Dome Gasket DomeFrame SET Hook Protective Camera Tape CoverInitial Setup Camera Address SetupCommunication Protocol Setup Samsung Half Samsung FullBaud Rate Setup Setting RS-422A/RS-485 TerminationUse pins #5, #6 of SW603 to set the baud rate Factory default is 9600 BPSRS-422A/RS-485 Full Duplex Organization Same address in the networkConnecting with Other device Connecting to a monitorMonitor Alarm Alarm OUT CONTROLLER/DVR Power SourceTo connect Alarm To connect Alarm OUTTo connect the controller Connecting the adaptor cable Power SupplyAdaptor Board How to use the keyboard controller Using OSD iconsCamera will resume the last run operation Main Menu Profile DAY Mode NightBurst EXT BurstYou can configure the general settings of the camera module Camera SETCamera ID  Location Specify the display position of the camera ID Manual Adjust the iris level manually With this, you can adjust the AGC level of aIris AGCMotion DNRShutter SENS-UPYou can specify a recording mode according to the scene FlickerlessXDR DAY/NIGHTAuto Switch or Auto Focus NeededSET-AUTO SET are not available White BAL DAY/NIGHT Zoom Speed Display ZoomDisplay P/T Digital ZoomSync AGC Color SUPReverse POSI/NEGAYou can enable the motion detection and tracking functions When multiple motions continue arbitrarilyIntelligent Video AdvancedResolution Alarm OUTPrivacy Zone DisplayPreset Select the preset number Select Position and adjust PANAuto Pan Setup Settings so define them again after the operationAuto SET You can set the Auto PAN, PATTERN, and Auto PlayPosition Direction Left Endless OFF Speed Pattern Setup Scan SetupSelect the Start and move the camera using pan/tilt/zoom Auto Play Setup ~ 511 for PresetZone SET You can set the north direction and the zone coverageSelect Main MENU-ZONE SET Alarm SET Select Main MENU-ALARM SET Auto SET Sets the pattern and scan Clock SET Other SETFactory Defaults PasswordOSD Color Proportional P/TCommunication System InfoYou can check the system information Select Main MENU-SYSTEM InfoLanguage You can set the language of the user interfaceShortcut Keys Function KeySpecifications Smart Dome CameraINT/LINE Lock PAN TiltProduct Appearance 00956B-NASCC-C7453N-ENG.indb 2009-08-13 오후