Samsung SCC-C7453N user manual Camera SET, Camera ID

Page 26

setup

CAMERA SET

You can configure the general settings of the camera module.

For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 22)

1.Select <MAIN MENU> - <CAMERA SET>. The Camera Setup menu appears.

2.Change the settings as necessary, or select an item to check.

CAMERA SET 

CAMERA ID	OFF
IRIS	ALC
MOTION	(F.FAST) ---
DNR	MID
SHUTTER	(OFF) ---
SENS-UP	AUTO X4
FLICKERLESS	OFF
XDR	MID

CAMERA ID

Provide the ID and location for a camera that displays on the screen.

For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 22)

1.Select <CAMERA SET> - <CAMERA ID>.

2.Use the joystick to select a desired character, then press [ENTER].

In the lower input box of the screen, the selected character will be entered.

You can enter up to 54 characters including alphabets, numbers and special characters.

LOCATION : Specify the display position of the camera ID.

CAMERA ID

ABCDEFGHIJKLMNOPQRSTUVWXYZO 123456789 : ?_+()/

SP SP LOCATION

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

3.When done, press [ENTER].

The camera ID will be displayed in the specified position.

26_ setup

00956B-NA_SCC-C7453N-ENG.indb 26

2009-08-13 오후 10:58:

Image 26

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents Features What’s IncludedFrame SET At a GlanceCamera Installation & connection Optional Accessories for InstallationEnglish Preparation PrecautionsHousing CableInstallation PIN Bush Power BNC Cable Bush 24V CableHousing Mount BushFrame SET 22P Connector Housing RackHousing Camera Screws Cover Dome Gasket Dome Hook Protective Camera Tape CoverCommunication Protocol Setup Initial SetupCamera Address Setup Samsung Half Samsung FullUse pins #5, #6 of SW603 to set the baud rate Baud Rate SetupSetting RS-422A/RS-485 Termination Factory default is 9600 BPSRS-422A/RS-485 Full Duplex Organization Same address in the networkMonitor Alarm Alarm OUT Connecting with Other deviceConnecting to a monitor CONTROLLER/DVR Power SourceTo connect the controller To connect AlarmTo connect Alarm OUT Adaptor Board Connecting the adaptor cablePower Supply Camera will resume the last run operation How to use the keyboard controllerUsing OSD icons Main Menu Profile Burst DAY ModeNight EXT BurstCamera ID You can configure the general settings of the camera moduleCamera SET  Location Specify the display position of the camera IDIris  Manual Adjust the iris level manuallyWith this, you can adjust the AGC level of a AGCShutter MotionDNR SENS-UPXDR You can specify a recording mode according to the sceneFlickerless DAY/NIGHTSET-AUTO SET are not available Auto Switch or Auto FocusNeeded White BAL DAY/NIGHT Display P/T Zoom SpeedDisplay Zoom Digital ZoomReverse SyncAGC Color SUP POSI/NEGAIntelligent Video You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily AdvancedPrivacy Zone ResolutionAlarm OUT DisplayPreset Select the preset number Select Position and adjust PANAuto SET Auto Pan SetupSettings so define them again after the operation You can set the Auto PAN, PATTERN, and Auto PlayPosition Direction Left Endless OFF Speed Select the Start and move the camera using pan/tilt/zoom Pattern SetupScan Setup Auto Play Setup ~ 511 for PresetSelect Main MENU-ZONE SET Zone SETYou can set the north direction and the zone coverage Alarm SET Select Main MENU-ALARM SET Auto SET Sets the pattern and scan Clock SET Other SETOSD Color Factory DefaultsPassword Proportional P/TYou can check the system information CommunicationSystem Info Select Main MENU-SYSTEM InfoLanguage You can set the language of the user interfaceShortcut Keys Function KeyINT/LINE Lock SpecificationsSmart Dome Camera PAN TiltProduct Appearance 00956B-NASCC-C7453N-ENG.indb 2009-08-13 오후