Samsung SCC-C7453N user manual Specifications, Smart Dome Camera, INT/LINE Lock

Page 51

Specifications

Item		Description

Product Type	SMART DOME CAMERA

Power Source	AC 24 V (60 Hz)

Power Consumption	16.3W(Camera, Fan) / 47W(Heater ON)

TV Standard	NTSC STANDARD COLOR SYSTEM

Image Sensor	Super-HAD IT CCD

Effective Pixels	768(H) × 494(V)

TV line frequency	Horizontal : 15, 734 Hz (INT) / 15, 750 Hz (L/L)
TV line frequency	Vertical : 59.94 Hz (INT) / 60 Hz (L/L)
	Vertical : 59.94 Hz (INT) / 60 Hz (L/L)

Synchronization	INT/LINE LOCK

Resolution	Horizontal : 600 TV LINES
Resolution	Vertical : 350 TV LINES
	Vertical : 350 TV LINES

S/N Ratio	Approximately 52 dB

	SENS-UP	Illumination	Color	B/W

	Off	50IRE	2	0.2

	Off	30IRE	1.2	0.12
Minimum subject
Minimum subject	Off	15IRE	0.6	0.06
illumination	Off	15IRE	0.6	0.06
illumination
	x512	50IRE	0.004	0.0004

	x512	30IRE	0.002	0.0002

	x512	15IRE	0.001	0.0001

Signal Output	COMPOSITE VIDEO OUT : 1.0 Vp-p 75 ohms/BNC

	x43 Zoom Lens Integrated
Lens	Focal length : 3.2 ~ 138.5mm
Lens	Aperture : F1.65(Wide) F3.7(Tale)
	Aperture : F1.65(Wide) F3.7(Tale)
	- MOD(Minimum Object Distance) : 100mm

English

English _51

00956B-NA_SCC-C7453N-ENG.indb 51

2009-08-13 오후 10:58:

Image 51

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents What’s Included FeaturesAt a Glance CameraFrame SET Optional Accessories for Installation Installation & connectionEnglish Cable PrecautionsHousing PreparationInstallation Bush Power BNC Cable Bush 24V CableHousing Mount PIN BushHook Protective Camera Tape Cover 22P Connector Housing RackHousing Camera Screws Cover Dome Gasket Dome Frame SETSamsung Half Samsung Full Initial SetupCamera Address Setup Communication Protocol SetupFactory default is 9600 BPS Baud Rate SetupSetting RS-422A/RS-485 Termination Use pins #5, #6 of SW603 to set the baud rateSame address in the network RS-422A/RS-485 Full Duplex OrganizationCONTROLLER/DVR Power Source Connecting with Other deviceConnecting to a monitor Monitor Alarm Alarm OUTTo connect Alarm To connect Alarm OUTTo connect the controller Connecting the adaptor cable Power SupplyAdaptor Board How to use the keyboard controller Using OSD iconsCamera will resume the last run operation Main Menu Profile EXT Burst DAY ModeNight Burst Location Specify the display position of the camera ID You can configure the general settings of the camera moduleCamera SET Camera IDAGC  Manual Adjust the iris level manuallyWith this, you can adjust the AGC level of a IrisSENS-UP MotionDNR ShutterDAY/NIGHT You can specify a recording mode according to the sceneFlickerless XDRAuto Switch or Auto Focus NeededSET-AUTO SET are not available White BAL DAY/NIGHT Digital Zoom Zoom SpeedDisplay Zoom Display P/TPOSI/NEGA SyncAGC Color SUP ReverseAdvanced You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily Intelligent VideoDisplay ResolutionAlarm OUT Privacy ZonePreset Select Position and adjust PAN Select the preset numberYou can set the Auto PAN, PATTERN, and Auto Play Auto Pan SetupSettings so define them again after the operation Auto SETPosition Direction Left Endless OFF Speed Pattern Setup Scan SetupSelect the Start and move the camera using pan/tilt/zoom ~ 511 for Preset Auto Play SetupZone SET You can set the north direction and the zone coverageSelect Main MENU-ZONE SET Select Main MENU-ALARM SET Alarm SET Auto SET Sets the pattern and scan Other SET Clock SETProportional P/T Factory DefaultsPassword OSD ColorSelect Main MENU-SYSTEM Info CommunicationSystem Info You can check the system informationYou can set the language of the user interface LanguageFunction Key Shortcut KeysSpecifications Smart Dome CameraINT/LINE Lock Tilt PANProduct Appearance 00956B-NASCC-C7453N-ENG.indb 2009-08-13 오후

Specifications

SMART DOME CAMERA

INT/LINE LOCK

English _51