Samsung SCC-C7453N 22P Connector Housing Rack, Frame SET, Hook Protective Camera Tape Cover

Page 15

3.Tie up the SAFETY WIRE of the CAMERA on the BRACKET WIRE of the FRAME SET.

Arrange the 22P CONNECTOR of the CAMERA in line with that of the ADAPTOR, push the HOOKs on either end of the CAMERA in the RACK direction of the FRAME SET to secure the two.

Then, ensure that all of the two HOOKs clicks to fix to the RACK properly.

22P CONNECTOR

HOUSING

 

RACK

RACK

BRACKET WIRE

 

FRAME SET

 

SAFETY WIRE

 

HOOK

PROTECTIVE

CAMERA

TAPE

 

PROTECTIVE

 

COVER

 

HOOK

M

When the installation is completed, remove the PROTECTIVE COVER and

 

PRETOECTIVE TAPE from the lens.

4.Align each of the 3 SCREWS of COVER DOME and 3 SCREW HOLEs of the HOUSING respectively, and assemble the COVER DOME and HOUSING. During the assembling, note on the followings.

Insert and arrange SAFETY WIRE into the HOUSING while not disturbing the camera operation.

Ensure that the GASKET DOME component does not separate from the COVER DOME. (If the GASKET DOME is not properly assembled, it damages the waterproofness.)

English

 

SAFETY WIRE

HOUSING

HOUSING

 

CAMERA

SCREWS

 

COVER DOME

GASKET DOME

COVER DOME

 

English _15

00956B-NA_SCC-C7453N-ENG.indb 15

2009-08-13 오후 10:58:

Image 15
Contents Smart Dome Camera Overview English  Overview FCC Statement Important safety instructions Contents What’s Included FeaturesAt a Glance CameraFrame SET Optional Accessories for Installation Installation & connectionEnglish Cable PrecautionsHousing PreparationInstallation Bush Power BNC Cable Bush 24V CableHousing Mount PIN BushHook Protective Camera Tape Cover 22P Connector Housing RackHousing Camera Screws Cover Dome Gasket Dome Frame SETSamsung Half Samsung Full Initial SetupCamera Address Setup Communication Protocol SetupFactory default is 9600 BPS Baud Rate SetupSetting RS-422A/RS-485 Termination Use pins #5, #6 of SW603 to set the baud rateSame address in the network RS-422A/RS-485 Full Duplex OrganizationCONTROLLER/DVR Power Source Connecting with Other deviceConnecting to a monitor Monitor Alarm Alarm OUTTo connect Alarm To connect Alarm OUTTo connect the controller Connecting the adaptor cable Power SupplyAdaptor Board How to use the keyboard controller Using OSD iconsCamera will resume the last run operation Main Menu Profile EXT Burst DAY ModeNight Burst Location Specify the display position of the camera ID You can configure the general settings of the camera moduleCamera SET Camera IDAGC  Manual Adjust the iris level manuallyWith this, you can adjust the AGC level of a IrisSENS-UP MotionDNR ShutterDAY/NIGHT You can specify a recording mode according to the sceneFlickerless XDRAuto Switch or Auto Focus NeededSET-AUTO SET are not available White BAL DAY/NIGHT Digital Zoom Zoom SpeedDisplay Zoom Display P/TPOSI/NEGA SyncAGC Color SUP ReverseAdvanced You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily Intelligent VideoDisplay ResolutionAlarm OUT Privacy ZonePreset Select Position and adjust PAN Select the preset numberYou can set the Auto PAN, PATTERN, and Auto Play Auto Pan SetupSettings so define them again after the operation Auto SETPosition Direction Left Endless OFF Speed Pattern Setup Scan SetupSelect the Start and move the camera using pan/tilt/zoom ~ 511 for Preset Auto Play SetupZone SET You can set the north direction and the zone coverageSelect Main MENU-ZONE SET Select Main MENU-ALARM SET Alarm SET Auto SET Sets the pattern and scan Other SET Clock SETProportional P/T Factory DefaultsPassword OSD ColorSelect Main MENU-SYSTEM Info CommunicationSystem Info You can check the system informationYou can set the language of the user interface LanguageFunction Key Shortcut KeysSpecifications Smart Dome CameraINT/LINE Lock Tilt PANProduct Appearance 00956B-NASCC-C7453N-ENG.indb 2009-08-13 오후