Samsung SCC-C7453N user manual How to use the keyboard controller, Using OSD icons

Page 22

setup

Connect the camera to the keyboard controller or DVR, with which you can manipulate and change the settings of the camera.

How to use the keyboard controller

Follow the steps below to set the camera menu using the controller.

1.Open the Camera Setup screen.

2.Use the joystick to navigate through the menus.

3.Press [ENTER] to select a menu item.

4.Use the joystick to change the value of the selected item.

5.Press [ENTER] to apply your changes.

Using OSD icons

_+: If these icons appear in the left and right corner of a menu item, you can use the joystick to move to the previous or next menu.

(EXIT): Exits the menu setup screen.

Before exiting the setup screen, select <SAVE> to save your settings to the whole menus, or <QUIT> to cancel them.

(RET): Saves your settings and returns to the previous screen.

(HOME): Returns to the main menu.

(SAVE): Use this icon if you want to save your settings after you specified the mask area and privacy area, etc.

Once you saved your settings, the changes remain intact even if you select <QUIT> on exit.

(DEL): Use this icon if you want to delete a mask, or privacy area, etc.

Once you deleted your settings, the deletions remain valid even if you select <QUIT> on exit.

: This icon appears in the right of a menu containing sub menu items.

M

While any operation of PRESET, AUTO PAN, SCAN, and PATTERN is running, and if

 

the camera is turned off and back on without any particular manipulation, the

 

camera will resume the last run operation.

 

You can set the menu item only if the tilt angle is within 90°.

 

If you enter the menu setup screen with the camera positioned out of a tilt of 90°,

 

the camera will rotate by 180° to fall into the opposite position within a tilt of 90°.

22_ setup

00956B-NA_SCC-C7453N-ENG.indb 22

2009-08-13 오후 10:58:

Image 22
Contents Smart Dome Camera Overview English  Overview FCC Statement Important safety instructions Contents Features What’s IncludedCamera At a GlanceFrame SET Installation & connection Optional Accessories for InstallationEnglish Preparation PrecautionsHousing CableInstallation PIN Bush Power BNC Cable Bush 24V CableHousing Mount BushFrame SET 22P Connector Housing RackHousing Camera Screws Cover Dome Gasket Dome Hook Protective Camera Tape CoverCommunication Protocol Setup Initial SetupCamera Address Setup Samsung Half Samsung FullUse pins #5, #6 of SW603 to set the baud rate Baud Rate SetupSetting RS-422A/RS-485 Termination Factory default is 9600 BPSRS-422A/RS-485 Full Duplex Organization Same address in the networkMonitor Alarm Alarm OUT Connecting with Other deviceConnecting to a monitor CONTROLLER/DVR Power SourceTo connect Alarm OUT To connect AlarmTo connect the controller Power Supply Connecting the adaptor cableAdaptor Board Using OSD icons How to use the keyboard controllerCamera will resume the last run operation Main Menu Profile Burst DAY ModeNight EXT BurstCamera ID You can configure the general settings of the camera moduleCamera SET  Location Specify the display position of the camera IDIris  Manual Adjust the iris level manuallyWith this, you can adjust the AGC level of a AGCShutter MotionDNR SENS-UPXDR You can specify a recording mode according to the sceneFlickerless DAY/NIGHTNeeded Auto Switch or Auto FocusSET-AUTO SET are not available White BAL DAY/NIGHT Display P/T Zoom SpeedDisplay Zoom Digital ZoomReverse SyncAGC Color SUP POSI/NEGAIntelligent Video You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily AdvancedPrivacy Zone ResolutionAlarm OUT DisplayPreset Select the preset number Select Position and adjust PANAuto SET Auto Pan SetupSettings so define them again after the operation You can set the Auto PAN, PATTERN, and Auto PlayPosition Direction Left Endless OFF Speed Scan Setup Pattern SetupSelect the Start and move the camera using pan/tilt/zoom Auto Play Setup ~ 511 for PresetYou can set the north direction and the zone coverage Zone SETSelect Main MENU-ZONE SET Alarm SET Select Main MENU-ALARM SET Auto SET Sets the pattern and scan Clock SET Other SETOSD Color Factory DefaultsPassword Proportional P/TYou can check the system information CommunicationSystem Info Select Main MENU-SYSTEM InfoLanguage You can set the language of the user interfaceShortcut Keys Function KeySmart Dome Camera SpecificationsINT/LINE Lock PAN TiltProduct Appearance 00956B-NASCC-C7453N-ENG.indb 2009-08-13 오후