Samsung SCC-C7453N user manual Initial Setup, Camera Address Setup, Communication Protocol Setup

Page 16

installation & connection

INITIAL SETUP

Camera Address Setup

Use SW606, SW605, and SW604 to specify the camera address.

You can specify between 0 and 255 for the address, where the hundreds digit is with SW606, the tens digit with SW605, and the ones digit with SW604.

ex) Camera address: If the address is 1, follow the steps in the figure below.

SW606

SW605

SW604

(x100)

(x10)

(x1)

Communication Protocol Setup

Use pins #1~#4 of SW603 to specify the communication protocol.

PIN	PIN1	PIN2	PIN3	PIN4
Comp	PIN1	PIN2	PIN3	PIN4
Comp
A	OFF	OFF	OFF	OFF
B	ON	OFF	OFF	OFF
C	OFF	ON	OFF	OFF
D	ON	ON	OFF	OFF
E	OFF	OFF	ON	OFF
F	ON	OFF	ON	OFF
G	OFF	ON	ON	OFF
H	ON	ON	ON	OFF
I	OFF	OFF	OFF	ON
J	ON	OFF	OFF	ON
K	OFF	ON	OFF	ON
L	ON	ON	OFF	ON
M	OFF	OFF	ON	ON
N	ON	OFF	ON	ON
O	OFF	ON	ON	ON
P	ON	ON	ON	ON

A : SAMSUNG HALF

B : SAMSUNG FULL

1_ installation & connection

00956B-NA_SCC-C7453N-ENG.indb 16

2009-08-13 오후 10:58:

Image 16

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents Features What’s IncludedCamera At a GlanceFrame SET Installation & connection Optional Accessories for InstallationEnglish Precautions HousingPreparation CableInstallation Power BNC Cable Bush 24V Cable Housing MountPIN Bush Bush22P Connector Housing Rack Housing Camera Screws Cover Dome Gasket DomeFrame SET Hook Protective Camera Tape CoverInitial Setup Camera Address SetupCommunication Protocol Setup Samsung Half Samsung FullBaud Rate Setup Setting RS-422A/RS-485 TerminationUse pins #5, #6 of SW603 to set the baud rate Factory default is 9600 BPSRS-422A/RS-485 Full Duplex Organization Same address in the networkConnecting with Other device Connecting to a monitorMonitor Alarm Alarm OUT CONTROLLER/DVR Power SourceTo connect Alarm OUT To connect AlarmTo connect the controller Power Supply Connecting the adaptor cableAdaptor Board Using OSD icons How to use the keyboard controllerCamera will resume the last run operation Main Menu Profile DAY Mode NightBurst EXT BurstYou can configure the general settings of the camera module Camera SETCamera ID  Location Specify the display position of the camera ID Manual Adjust the iris level manually With this, you can adjust the AGC level of aIris AGCMotion DNRShutter SENS-UPYou can specify a recording mode according to the scene FlickerlessXDR DAY/NIGHTNeeded Auto Switch or Auto FocusSET-AUTO SET are not available White BAL DAY/NIGHT Zoom Speed Display ZoomDisplay P/T Digital ZoomSync AGC Color SUPReverse POSI/NEGAYou can enable the motion detection and tracking functions When multiple motions continue arbitrarilyIntelligent Video AdvancedResolution Alarm OUTPrivacy Zone DisplayPreset Select the preset number Select Position and adjust PANAuto Pan Setup Settings so define them again after the operationAuto SET You can set the Auto PAN, PATTERN, and Auto PlayPosition Direction Left Endless OFF Speed Scan Setup Pattern SetupSelect the Start and move the camera using pan/tilt/zoom Auto Play Setup ~ 511 for PresetYou can set the north direction and the zone coverage Zone SETSelect Main MENU-ZONE SET Alarm SET Select Main MENU-ALARM SET Auto SET Sets the pattern and scan Clock SET Other SETFactory Defaults PasswordOSD Color Proportional P/TCommunication System InfoYou can check the system information Select Main MENU-SYSTEM InfoLanguage You can set the language of the user interfaceShortcut Keys Function KeySmart Dome Camera SpecificationsINT/LINE Lock PAN TiltProduct Appearance 00956B-NASCC-C7453N-ENG.indb 2009-08-13 오후