3M MT7 Drawing Lines Are Not Straight and Smooth, Find Sensor for Serial Plug & Play Controllers

Page 57

3M™ MicroTouch™ Software MT 7 User Guide

57

The double-click area defines the space in which you must touch the sensor for the system to interpret your actions as a double-click. Set the double-click area in the medium to high range for optimum performance with a sensor.

Click on the globe to test the double-click speed and area settings. If globe begins to spin, the sensor recognized your touch as a double-click.

Note: Changing this setting will affect the double-click setting of the mouse.

Drawing Lines Are Not Straight and Smooth

Contact 3M Touch Systems, Inc. Technical Support for assistance performing a manual linearization.

Find Sensor (for Serial Plug & Play Controllers)

Note: This option applies to Windows® only.

1.Do a Find New Hardware from Windows® control panel.

2.Reinstall MT 7 using the Custom installation option and make sure you are choosing the correct controller support.

3.Reboot your system and try again. If the problem persists, call 3M Touch Systems, Inc. Technical Support.

Note: Verify that any previously loaded hardware and/or software installed in the same serial port as your sensor has been uninstalled. Even though the hardware has been disconnected, the software can still claim the port. Ensure that all components are completely removed from the system files.

Touch Is Not Working

If the controller information box on the Main Tab is grayed out and contains no information, the sensor is not communicating with the controller. If MT 7 does not find the sensor, check that the sensor is connected properly.

If you are experiencing problems with the sensor, check that all cables are connected properly and restart your system.

To correct the communication settings in a Windows® system, use the Windows® Hardware Conflict Troubleshooter from Windows® Help .

Note: Verify that any previously loaded hardware and/or software installed in the same serial port as your sensor has been uninstalled. Even though the hardware has been disconnected, the software can still claim the port. Ensure that all components are completely removed from the system files.

3M Touch Systems, Inc. Proprietary Information – 25695M

Image 57

Contents 3M MicroTouch Software MT User Guide 3M MicroTouch Software MT 7 User Guide Contents Appendix a Multiple Monitor Setup Windows Only Sensor Care and Cleaning About This ManualIntroduction Contact 3M Touch Systems 3M Touch Systems Support ServicesMT 7 Software Overview Installing MT 7 SoftwareTouch Drivers MT 7 Control PanelOnline Help MT 7 Windows Software Uninstall Utility Installing MT 7 SoftwareCalibration Tool Multiple Display ManagerDriver Selection User Interface Utilities and Tools Performing a Silent InstallUninstalling MT 7 Software Customizing Your SettingsMT 7 Software Control Panel OverviewOpening the MT 7 Control Panel Calibration Main TabCalibrating the Sensor Testing the Calibration Support InformationController ID Controller Type Firmware VersionSensor Status Touch Settings Tab Drawing Mode Default ValueTouch Modes Liftoff Mode Touchdown ModeRight-Click Tool not available on Linux Touch SoundEdge Adjustment Tab Double-Click Speed not available on Windows CE or LinuxDouble-Click Area not available on Windows CE or Linux Edge Adjustment Setting 3M MicroTouch Software MT 7 User Guide Component Versions Tools TabDraw Test Restore Factory SettingsSoftware ControllerAdvanced Touch Options Reset ControllerController Tab Linearization Process LinearizationPen Overview Pen Controller Only Pen and Finger CalibrationPen Modes Sensor Frequency Procedure Testing the Newly Selected FrequencySensor Frequency Controller ID Windows CE Overview Installation InstructionsLicense Agreement WelcomeSelect Installation Folder Installation Complete Confirm Installation3M MicroTouch Software MT 7 User Guide 3M MicroTouch Software MT 7 User Guide Slow Draw Anomalies Page Windows XP Embedded Overview Loading MT 7 Into The Components Database ManagerMT 7 Component Selection In Target Designer MT 7 Components System Requirements MT 7 for Linux OverviewHardware Prerequisites Software PrerequisitesBefore Driver Installation General InstructionsPreparation Normal Installation Installing on Write-Protected SystemsOther Options HotplugDir XinitDir and XinitSuffix Error Messages During InstallationCannot find needed libstdc++.so in /usr/lib Removing MT 7 For Linux Troubleshooting The Init ScriptRunning Touch Applications Troubleshooting Touch BehaviorCalibration Messages Are Unreadable Known IssuesPage Multiple Monitor Setup Windows Only Setting Up Multiple MonitorsChanging the Controller ID 3M MicroTouch Software MT 7 User Guide 3M MicroTouch Software MT 7 User Guide Page Other Serial Devices Do Not Work Troubleshooting the Touch SystemCursor Does Not Reach Edges of Display Multiple Display SupportCursor is Jittery Cursor Jumps or Bounces Suddenly Across the DisplayDrawing Lines Are Not Straight and Smooth Find Sensor for Serial Plug & Play ControllersTouch Is Not Working Right-click Tool Buttons Are Swapped Touch Driver Did Not LoadPrevious Version of TouchWare Software Was Detected