3M Comprehensive Guide to the Touch System for MicroTouch Software MT 7

Page 17

3M™ MicroTouch™ Software MT 7 User Guide

17

Controller Type

This field displays the type of controller currently attached to your system. This data may be useful for Technical Support issues. The touch controllers supported with this release are as follows:

EX USB, HID, and Serial capacitive and resistive controllers

DX Dual mode (USB and Serial) controllers

PX Dual mode (USB and Serial) controllers

RX USB and Serial resistive controllers

SX Serial pen controllers

Firmware Version

These digits represent the version number and revision level of the touch controller firmware.

Sensor Status

Sensor Status refers to whether or not the sensor has been found and is operational.

Some of the possible messages include:

OK – Sensor found and operational.

BLK Error – Hardware error such as a checksum error in controller EEPROM.

∙ CBL Error – Cable NOVRAM missing – this is only an error in systems requiring cable NOVRAM.

HDW Error – Hardware error.

LIN Error – Linearity data error.

NOV Error – Checksum error in NOVRAM, using default s.

PWM Error – Hardware error.

ROM Error – Checksum error in ROM.

SET Error – Unable to establish operating range at power-up.

Any other condition indicates a hardware failure. Contact Technical Support for more information.

3M Touch Systems, Inc. Proprietary Information – 25695M

Image 17
Contents 3M MicroTouch Software MT User Guide 3M MicroTouch Software MT 7 User Guide Contents Appendix a Multiple Monitor Setup Windows Only Introduction Sensor Care and CleaningAbout This Manual Contact 3M Touch Systems 3M Touch Systems Support ServicesMT 7 Software Overview Installing MT 7 SoftwareTouch Drivers MT 7 Control PanelOnline Help MT 7 Windows Software Uninstall Utility Installing MT 7 SoftwareCalibration Tool Multiple Display ManagerDriver Selection User Interface Utilities and Tools Performing a Silent InstallUninstalling MT 7 Software Customizing Your SettingsOpening the MT 7 Control Panel MT 7 Software Control PanelOverview Calibration Main TabCalibrating the Sensor Controller ID Testing the CalibrationSupport Information Sensor Status Controller TypeFirmware Version Touch Modes Touch Settings TabDrawing Mode Default Value Liftoff Mode Touchdown ModeRight-Click Tool not available on Linux Touch SoundDouble-Click Area not available on Windows CE or Linux Edge Adjustment TabDouble-Click Speed not available on Windows CE or Linux Edge Adjustment Setting 3M MicroTouch Software MT 7 User Guide Component Versions Tools TabDraw Test Restore Factory SettingsSoftware ControllerAdvanced Touch Options Reset ControllerController Tab Linearization Process LinearizationPen Modes Pen Overview Pen Controller OnlyPen and Finger Calibration Sensor Frequency Sensor Frequency ProcedureTesting the Newly Selected Frequency Controller ID Windows CE Overview Installation InstructionsLicense Agreement WelcomeSelect Installation Folder Installation Complete Confirm Installation3M MicroTouch Software MT 7 User Guide 3M MicroTouch Software MT 7 User Guide Slow Draw Anomalies Page MT 7 Component Selection In Target Designer Windows XP Embedded OverviewLoading MT 7 Into The Components Database Manager MT 7 Components System Requirements MT 7 for Linux OverviewHardware Prerequisites Software PrerequisitesPreparation Before Driver InstallationGeneral Instructions Other Options Normal InstallationInstalling on Write-Protected Systems HotplugDir XinitDir and XinitSuffix Error Messages During InstallationCannot find needed libstdc++.so in /usr/lib Removing MT 7 For Linux Troubleshooting The Init ScriptRunning Touch Applications Troubleshooting Touch BehaviorCalibration Messages Are Unreadable Known IssuesPage Changing the Controller ID Multiple Monitor Setup Windows OnlySetting Up Multiple Monitors 3M MicroTouch Software MT 7 User Guide 3M MicroTouch Software MT 7 User Guide Page Other Serial Devices Do Not Work Troubleshooting the Touch SystemCursor Does Not Reach Edges of Display Multiple Display SupportCursor is Jittery Cursor Jumps or Bounces Suddenly Across the DisplayTouch Is Not Working Drawing Lines Are Not Straight and SmoothFind Sensor for Serial Plug & Play Controllers Right-click Tool Buttons Are Swapped Touch Driver Did Not LoadPrevious Version of TouchWare Software Was Detected