3M MT7 manual Touch Driver Did Not Load, Right-click Tool Buttons Are Swapped

Page 58

58

3M™ MicroTouch™ Software MT 7 User Guide

Check the following items:

1.Make sure the touch controller is connected to the correct port.

2.Review the installation procedures and verify all hardware is properly connected. Check the serial port and sensor cable connections. Check that the sensor and controller cables do not have any kinks and that connector pins are not bent.

3.Reset the sensor and its controller. Turn off both the computer and the display, wait a few minutes, and then turn on each device again.

Touch Driver Did Not Load

Check Windows® device manager under mice and pointing devices to see if the MicroTouch drive is loaded and running without errors (under system devices for the MicroTouch bus driver (used only for EX serial sensors)).

If these are missing, run Installdriver.bat inside WINNT\Program Files\

MicroTouch\MT7 to reload the driver.

If this does not work then run Removedriver.bat, reboot then rerun Installdriver.bat.

Right-click Tool Buttons Are Swapped

Using the control panel, it is possible to change which button on a mouse generates the "left" and "right" clicks. This feature allows left-handed people to use their index finger to produce a left click. This setting causes the touch driver to also reverse the meaning of a touch. Normally, a touch produces a left click. With the changed setting above, a touch starts producing a right-click.

To address this, edit the file "TwFactory.cfg" in the MT 7 for Windows™ software directory. If this file is empty, add in the text:

<Touch>

</Touch>

Between these two lines, add a new line:

SwapMouseButtons=1

Save the file.

Open a command line window and set your working directory to the MT 7 for

Windows™ directory. Issue the command: TwCfgUtil / u TwFactory.cfg

At this point, your touches start producing the desired left-clicks.

If your system supports multiple users, you may need to create separate files, such as TwLeft.cfg and TwRight.cfg. In TwLeft.cfg, set SwapMouseButtons to 1 and in TwRight.cfg, set SwapMouseButtons to 0.

Add the above TwCfgUtil to each user's Startup menu or login script, using TwLeft.cfg or TwRight.cfg as appropriate.

3M Touch Systems, Inc. Proprietary Information – 25695M

Image 58
Contents 3M MicroTouch Software MT User Guide 3M MicroTouch Software MT 7 User Guide Contents Appendix a Multiple Monitor Setup Windows Only About This Manual Sensor Care and CleaningIntroduction 3M Touch Systems Support Services Contact 3M Touch SystemsTouch Drivers Installing MT 7 SoftwareMT 7 Software Overview MT 7 Control PanelCalibration Tool Installing MT 7 SoftwareOnline Help MT 7 Windows Software Uninstall Utility Multiple Display ManagerDriver Selection User Interface Performing a Silent Install Utilities and ToolsCustomizing Your Settings Uninstalling MT 7 SoftwareOverview MT 7 Software Control PanelOpening the MT 7 Control Panel Main Tab CalibrationCalibrating the Sensor Support Information Testing the CalibrationController ID Firmware Version Controller TypeSensor Status Drawing Mode Default Value Touch Settings TabTouch Modes Right-Click Tool not available on Linux Touchdown ModeLiftoff Mode Touch SoundDouble-Click Speed not available on Windows CE or Linux Edge Adjustment TabDouble-Click Area not available on Windows CE or Linux Edge Adjustment Setting 3M MicroTouch Software MT 7 User Guide Tools Tab Component VersionsSoftware Restore Factory SettingsDraw Test ControllerReset Controller Advanced Touch OptionsController Tab Linearization Linearization ProcessPen and Finger Calibration Pen Overview Pen Controller OnlyPen Modes Testing the Newly Selected Frequency Sensor Frequency ProcedureSensor Frequency Controller ID Installation Instructions Windows CE OverviewWelcome License AgreementSelect Installation Folder Confirm Installation Installation Complete3M MicroTouch Software MT 7 User Guide 3M MicroTouch Software MT 7 User Guide Slow Draw Anomalies Page Loading MT 7 Into The Components Database Manager Windows XP Embedded OverviewMT 7 Component Selection In Target Designer MT 7 Components Hardware Prerequisites MT 7 for Linux OverviewSystem Requirements Software PrerequisitesGeneral Instructions Before Driver InstallationPreparation Installing on Write-Protected Systems Normal InstallationOther Options HotplugDir Error Messages During Installation XinitDir and XinitSuffixCannot find needed libstdc++.so in /usr/lib Troubleshooting The Init Script Removing MT 7 For LinuxTroubleshooting Touch Behavior Running Touch ApplicationsKnown Issues Calibration Messages Are UnreadablePage Setting Up Multiple Monitors Multiple Monitor Setup Windows OnlyChanging the Controller ID 3M MicroTouch Software MT 7 User Guide 3M MicroTouch Software MT 7 User Guide Page Troubleshooting the Touch System Other Serial Devices Do Not WorkCursor is Jittery Multiple Display SupportCursor Does Not Reach Edges of Display Cursor Jumps or Bounces Suddenly Across the DisplayFind Sensor for Serial Plug & Play Controllers Drawing Lines Are Not Straight and SmoothTouch Is Not Working Touch Driver Did Not Load Right-click Tool Buttons Are SwappedPrevious Version of TouchWare Software Was Detected