8 Select the desired channel by pressing 
or 
, then press MODE.
When L+R is selected :
FRONT 1 
FRONT 2 
REAR 
CENTER 
SUBWOOFER 
FRONT 1
When L/R is selected :
FRONT 1L 
FRONT 1R 
FRONT 2L 
FRONT 2R 
REAR L 
REAR R 
CENTER 
SUBWOOFER 
FRONT 1L
•The speakers display differs, depending on the connected speakers.
9 Adjust the calculated time correction value (0.00 to 20.00ms) by turning the Rotary encoder, then press MODE.
Switching the Phase
10 Switch the phase (PHASE 0° or 180°) by turning the Rotary encoder, then press MODE.
11 To adjust other channels, repeat steps 8 to 10.
12 When the setting is complete, press and hold TA for at least 2 seconds.
The unit returns to the normal mode.
•When the speaker is set to the “OFF” mode, the TCR for that speaker cannot be set. Refer to “Setting the Speakers” (page 37).
•The adjustment value for FRONT2 (Speakers) which is adjusted in time correction, is also applied to the front speakers in “Setting Bass Focus” (page 41).
•The adjustment (AUTO TCR) cannot be automatically set on this unit.
•When the setting is complete, it is recommended to store the setting contents. For storing, refer to page 44.
Graphic Equalizer Adjustments
The graphic equalizer allows you to modify the sound using 31 bands each for the front (left and right), rear (left and right) and centre speakers. An additional 10 bands are available for the subwoofer. This allows you to customize the sound to suit your taste.
1 Check that Defeat mode is off (page 25). 2 Press and hold TA for at least 2 seconds.
The audio processor control mode is activated.
3 Select the
4 Select L+R or L/R by pressing and holding BAND for at least 2 seconds.
L+R: Sets the same adjustment values for the left and right channels.
L/R: Different adjustment values can be set for the left and right channels.
When parametric EQ is adjusted, this setting will be turned off.
5 Select the desired channel by pressing 
or 
, then press MODE.
When L+R is selected :
FRONT 
REAR 
CENTER 
SUBWOOFER 
FRONT
When L/R is selected :
FRONT L 
FRONT R 
REAR L 
REAR R 
CENTER 
SUBWOOFER 
FRONT L
•The speakers display differs, depending on the connected speakers.
6 Select the frequency by turning the Rotary
encoder, then press MODE.
Adjustable frequency:
FRONT/REAR/CENTER: 20Hz - 20kHz (in 1/3 octave steps)
SUBWOOFER: 20Hz - 160Hz (in 1/3 octave steps)
7 Adjust the level (LEVEL) (±9dB 1dB step) by turning the Rotary encoder, then press MODE.
8 To adjust other frequencies, repeat steps 6 and 7.
9 To adjust other channels, repeat steps 5 to 8.
10 When the setting is complete, press and hold TA for at least 2 seconds.
The unit returns to the normal mode.
•When the speaker is set to the “OFF” mode, the level of the graphic equalizer for that speaker cannot be adjusted. Refer to “Setting the Speakers” (page 37).
•Check the playable frequency ranges of the connected speakers before making the equalizer adjustments. If the speaker’s playable frequency range is 55 Hz to 30 kHz, for example, adjusting the 40 Hz or 20 Hz band has no effect. Additionally, you may overload and damage the speakers.
•When graphic EQ is adjusted, the adjustment for parametric EQ becomes ineffective.
•When the setting is complete, it is recommended to store the setting contents. For storing, refer to page 44.