Schneider Electric DS301 manual Commissioning the device

Page 53

IL•1F CANopen DS301

5 Commissioning

5 Commissioning

@ DANGER

UNINTENDED CONSEQUENCES OF EQUIPMENT OPERATION

When the system is started, the drives are usually out of the opera- tor's view and cannot be visually monitored.

•Only start the system if there are no persons in the hazardous area.

Failure to follow these instructions will result in death or serious injury.

@ WARNING

UNINTENDED OPERATION

•Do not write values to reserved parameters.

•Do not write values to parameters unless you fully understand the function. For more information see the product manual.

•Run initial tests without coupled loads.

•Verify that the system is free and ready for the movement before changing parameters.

•Verify the use of the bits with fieldbus communication: bit 0 is far right (least significant). Bit 15 is far left (most significant).

•Verify the use of the word sequence with fieldbus communication.

•Do not establish a fieldbus connection unless you have fully understood all communications principles.

Failure to follow these instructions can result in death, serious injury or equipment damage.

5.1Commissioning the device

For installation in the network, the device must first be properly installed (mechanically and electrically) and commissioned.

Commission the device as per product manual. This prepares the device for operation in the network.

0198441113586, V2.01, 11.2008

Fieldbus interface

53

Image 53

Contents IL1F CANopen DS301 Important information Table of Contents Table of Contents IL1F CANopen DS301 Object directory Table of Contents IL1F CANopen DS301 Writing conventions and symbols Writing conventions and symbols IL1F CANopen DS301 CAN-Bus IntroductionAbout this manual Fieldbus devices networked via can bus Operating modes and functions in fieldbus modeCan users and manufacturers organization Documentation and literature referencesIntroduction IL1F CANopen DS301 Before you begin safety information Before you begin safety information IL1F CANopen DS301 CANopen technology BasicsCANopen description language Communication layersIndex hex Object groups Supported By the drive ObjectsIL1F CANopen DS301 Basics CANopen reference model CANopen profilesIndex Subindex Object Meaning Communication profileObject dictionary Index range Object groups Supported Hex By the drive Communication objects Communication objectsCOB ID with function code and node address TPDO4 Master slave relationships Communication relationshipsClient-server relationship SDO data exchange Service data communicationOverview 11 SDO message, example SDO messageMessage type Data length used Bytes Reading and writing dataMessage type Data length used Byte Bytes 14 Reading a parameter value15 Response with error message error response Process data communication 16 PDO data exchange PDO data exchangeUINT32 18 Requesting a message with RTR = Dynamic and static PDO mappingStructure of RPDO4 Receive PDO RPDO4 master slaveState machine drivectrl JOG Operating modes modeCtrlTransmit PDO TPDO4 product to master @ Warning20 Structure of TPDO4 Structure of TPDO4Bit Name Description Handshake with Mode Toggle BitMaster Slave Xend 22 Mode Toggle Handshake, short movementBasics IL1F CANopen DS301 23 Error message with the Emcy object Emergency service25 Sync message Synchronization27 Cyclic and acyclic transmission NMT services for device control Network management servicesPersistent data memory NMT service Transition MeaningInitialization Node/Life guarding NMT services for connection monitoringCommand Specifier NMT service Transition 31 Acknowledgement of the NMT slave 32 Node Guarding and Life Guarding with time intervals Installation Installation IL1F CANopen DS301 Commissioning the device CommissioningCommissioning the fieldbus network Starting fieldbus modeAddress and baud rate Error Error class Cause of error Troubleshooting TroubleshootingSelecting the CANopen master SyCon CANopen configuration softwareCreating a new network Setting the bus parameters Selecting and inserting nodes Overview OperationOperation IL1F CANopen DS301 Writing parameters Using SDO commandsTransmit data Receive dataIndex Sub Data Description Synchronous errorsReading a parameter Bit no Value Meaning Operating Name Power Description State StageChanging operating states with PDO4 Example Switching the power stage on and offTriggering a Quick Stop Come to a standstill System is to resume opera Resetting faults Examples for the operating modes with PDO4 Operating mode Profile Position absolute positioning Operating mode Profile Velocity Operating mode Profile Position relative positioningMaster --- Slave Position settingOperating mode Homing Asynchronous errors Error signaling via PDO4Positioning running xerr=0 Operation IL1F CANopen DS301 Fieldbus communication error diagnostics Diagnostics and troubleshootingMessages on the device status Error diagnostics via fieldbusMessage objects Error register CANopen error messagesError code table Bit Message MeaningError code Meaning SDO error message AbortObject directory Specifications for the objectsObject code Meaning Coding Data type Value range Data lengthObjects, overview Index Subindex Designation Obj. code Data type AccessDevice type Error registerObjects of the product 1008h Bit coding, subindex 00hManufacturer device name 100ChIndex 100D h Object name Life time factor Object code Index 1018 h Object name Identity Object Object code Data type PDO Communication parameter Bit 30 RTR bit Bit assignment subindex 01hBit coding, subindex 02h Bit Acces Value Meaning1603h Receive PDO4 mapping Value description BitMeaning 1803h Transmit PDO4 communication parameterSubindex 03 h, inhibit time TPDO4 Meaning IL1F CANopen DS301 Object directory PDO4 mapping 1603h Units and conversion tables GlossaryRotation TemperatureTorque Moment of inertiaTerms and Abbreviations Default value Factory settingPower amplifier See power stage Can IndexIndex IL1F CANopen DS301 IL1F CANopen DS301 Index NMT IL1F CANopen DS301 Index 102 Fieldbus interface