Ericsson R290 manual Charging the Battery

Page 13

Operating with a GSM Standard SIM Card

Your phone will operate in GSM mode with a standard GSM SIM card. You can change parameters to override the default satellite parameters. This allows you to set your personal preferences for use in GSM networks.

Enhanced SIM

Your phone will operate with an enhanced SIM but many of the addition features of the SIM will not be available.

The Battery

Your mobile phone comes with a Lithium Ion (Li-ion) battery. The battery is not fully charged when purchased, but there may be enough power to turn on the phone.

Attaching the Battery to the Phone:

1. Place the battery on the back of the phone as shown.

R290 User’s Guide

2.Press the battery forward and press down on the rear of battery until you hear a click.

Removing the Battery

Make sure that the phone is turned off before removing the battery, then:

1.Press the battery release button.

2.Lift the battery up and away from the phone.

Low battery indication

When the battery is running low, the message Battery Low will flash on the display and the LOW BATTERY WARNING TONE will be played. When the battery is nearly empty, the phone will shut down.

Charging the Battery

Follow these steps to connect the charger to the power socket and to the phone;

5

Image 13

Contents Ericsson R290 Satellite Innovatron Patents Product Care and Maintenance Safety InstructionsGuidelines for Safe and Efficient Use Electronic Devices DrivingAircraft Blasting AreasBattery Information Please note Recycling Your BatteryContents Warranty Introduction Globalstar/GSM About Your PhoneOperators & Subscriptions SIM CardPhone Operating Without a SIM Card Preparing Your Phone for UseInserting the SIM Card Charging the Battery BatteryR290 User’s Guide When to Charge the Battery Disconnecting the ChargerLow Battery Alarm AntennaUse with Mobile Office Globalstar Mode Use with Portable Hands Free Globalstar ModeTurning On the Phone Turning Off the PhoneNavigating the Menu System Display Text and SymbolsTerms Used Icon Function Indicators in the DisplayInitial Phone Settings Selecting a Network Searching for a NetworkStand-by display Making and Receiving Calls Answering a Call Receiving a CallRejecting a Call Calling Line Identification CLIHandling Two Calls Useful Information while Talking To Change Key Tone Volume To Change the Ring VolumeUsing Auto-Redial To Redial the Last Dialled NumberMaking/Answering a Call with Call Bar Active Missed CallsNotification that a Call has been Diverted To dial the last 10 numbers dialled, received or missedAbout the Phone Book Using the Phone BookInternational Numbers Speed DiallingTo Store a Name and a Number into a Selected Memory Store Upper Case ModeLower Case Mode To Edit a Number from Memory Store To Store Your Own Telephone NumberLast Number Stores To Display your Own Telephone NumberDialled Store Pause Dialling Last Number RedialReceived Store Missed StoreOne-Touch Dialling Sending Dtmf Tones During a CallCall Duration and Cost Last CallCall Cost Setup To Reset the Call Time/Cost CountersAll Calls To Setup the Unit Time for Calls ‘ Cost Limit Approaching’ being displayed To set the maximum costBusy Numbers Personalizing Your PhoneRing Tone Ring VolumeTo Complete a Ccbs Call Caller ID Escalating Ring VolumeConnect ID Auto Answer Automatic Display of Call TimeGreetings ClockDate Mode Clock ModeSet Time Set DateLanguage Mode Satellite Synchronisation ModeLanguage To Choose a LanguageVisual Indicator Usage Power SaveBacklight Operation Fixed Dialled Number Store Handsfree Automatic Shutdown TimerVoice Mail Protecting Your Phone Setting the Keypad LockAbout Locks Phone Lock PIN To Enable the Phone PINTo unlock the keypad Unblocking with Personal Unblocking Key PUK To Disable the Phone PINTo Change the Phone PIN Card Lock SIM PIN To Enable the SIM PIN LockTo change the SIM PIN Controlling Your Calls To Disable the SIM PIN LockCall Divert To Review the Call Divert StatusTo Setup Call Divert Notification that a Call has been Diverted Call WaitingTo Remove Call Diversion To Check the Call Wait Status To Cancel Call WaitingTo Set Call Waiting Dealing with Multiple Calls Switching between Active Call and Call on HoldCall Waiting In-Call Menu Placing a Second Call and holding the Current CallConference Calls Placing a Call when the Called Party is EngagedCall Termination by Calling Party with another Call Held To Create a Conference CallTo Review the Participants in a Conference Call To Disconnect a Remote Party from a Conference Call Call Control Public MMI Commands SummaryCall Hold and Call Termination by a Remote Party Remote Party NotificationTo Check the Call Bar Status Call BarringTo Set Incoming Call Barring To Set Outgoing Call BarringTo Cancel Incoming Call Barring To Cancel Outgoing Call BarringTo Change the Network Password for Call Barring Sending And Receiving Text Messages Quick access to unread messagesReceiving a Message Checking SubscriptionDeleting a Message To Read a MessageSaving and Dialling a Number Received in a Message Clearing Messages Automatically To Select Message TonesSending a Message Displaying Priority Messages ImmediatelyTo Originate a New Message To Enter Message Text To Enter the Service Centre NumberTo Enter the Destination Address To Select the Message Type To Enter the Validity PeriodTo Review Your Newly Created Message To Create a Message from an Existing MessageTo Save a Message To Send the Completed MessageTo Return to the Current Message and complete it To Delete a MessageTo Check on the Status of the Last Message Sent To Set the Message Parameter DefaultsOur Warranty WarrantyWhat We Will Do ConditionsPatents R290 User’s Guide Index PIN