Ericsson R290 manual Sending Dtmf Tones During a Call, One-Touch Dialling, Call Duration and Cost

Page 34

R290 User’s Guide

character space. The digits that you add after the PAUSE will be transmitted as DTMF tones across the network. For example:

You can send the number in the usual manner, or store, dial or edit it, or clear the number from the display. You can also recall the number from the phone book stores.

If you dial the number, when the DTMF tones are signalled over the network they are echoed through the earpiece so that you can hear what is happening. You can terminate the call as normal.

You may enter any number of PAUSES into a number. The number must not exceed 61 characters including the international prefix.

Sending DTMF Tones During a Call

You can generate DTMF tones manually while a call is in progress. This facility can be enabled/disabled from the Call Set-up Menu by selecting

5 followed by YES. The display will be:

To enable the DTMF tones press 1 or YES. To disable them, press 2. A confirmation message will be displayed before the phone returns to the Call Setup Menu.

If the DTMF tones have been disabled and you need to send DTMF tones during a call, you can enable them using the In-call Menu.

When enabled, any numerical key press, including <* and #>, will cause DTMF tones to be signalled across the network.

One-Touch Dialling

You can use the one-touch dialling function by pressing and holding the digit keys 1 to 9 for at least half a second. The number contained in the phone book store is recalled and is dialled automatically.

Call Duration and Cost

The Call Time Menu sets the phone to record approximate call time and cost.

Last Call

1. Press SOFT LEFT, 2, to enter the Call Time Menu.

2.Press 1 or YES to display the duration and cost of the last call made. The time is displayed in hours, minutes and seconds. The cost is displayed in the chosen currency.

NOTE:

The cost is only displayed if the call rate charges (unit cost) have been entered into the phone, see “Call Cost Setup” on page 27. If you have set the call charging parameters to zero, only the duration of the call will be displayed.

26

Image 34

Contents Ericsson R290 Satellite Innovatron Patents Product Care and Maintenance Safety InstructionsGuidelines for Safe and Efficient Use Aircraft DrivingElectronic Devices Blasting AreasBattery Information Recycling Your Battery Please noteContents Warranty Introduction Operators & Subscriptions About Your PhoneGlobalstar/GSM SIM CardPhone Operating Without a SIM Card Preparing Your Phone for UseInserting the SIM Card Battery Charging the BatteryR290 User’s Guide Low Battery Alarm Disconnecting the ChargerWhen to Charge the Battery AntennaTurning On the Phone Use with Portable Hands Free Globalstar ModeUse with Mobile Office Globalstar Mode Turning Off the PhoneNavigating the Menu System Display Text and SymbolsTerms Used Indicators in the Display Icon FunctionInitial Phone Settings Searching for a Network Selecting a NetworkStand-by display Making and Receiving Calls Rejecting a Call Receiving a CallAnswering a Call Calling Line Identification CLIHandling Two Calls Useful Information while Talking Using Auto-Redial To Change the Ring VolumeTo Change Key Tone Volume To Redial the Last Dialled NumberNotification that a Call has been Diverted Missed CallsMaking/Answering a Call with Call Bar Active To dial the last 10 numbers dialled, received or missedInternational Numbers Using the Phone BookAbout the Phone Book Speed DiallingUpper Case Mode To Store a Name and a Number into a Selected Memory StoreLower Case Mode To Store Your Own Telephone Number To Edit a Number from Memory StoreLast Number Stores To Display your Own Telephone NumberDialled Store Received Store Last Number RedialPause Dialling Missed StoreCall Duration and Cost Sending Dtmf Tones During a CallOne-Touch Dialling Last CallCall Cost Setup To Reset the Call Time/Cost CountersAll Calls To Setup the Unit Time for Calls To set the maximum cost ‘ Cost Limit Approaching’ being displayedPersonalizing Your Phone Busy NumbersRing Tone Ring VolumeTo Complete a Ccbs Call Caller ID Escalating Ring VolumeConnect ID Greetings Automatic Display of Call TimeAuto Answer ClockSet Time Clock ModeDate Mode Set DateLanguage Satellite Synchronisation ModeLanguage Mode To Choose a LanguageVisual Indicator Usage Power SaveBacklight Operation Fixed Dialled Number Store Handsfree Automatic Shutdown TimerVoice Mail Protecting Your Phone Setting the Keypad LockAbout Locks Phone Lock PIN To Enable the Phone PINTo unlock the keypad Unblocking with Personal Unblocking Key PUK To Disable the Phone PINTo Change the Phone PIN Card Lock SIM PIN To Enable the SIM PIN LockTo change the SIM PIN Call Divert To Disable the SIM PIN LockControlling Your Calls To Review the Call Divert StatusTo Setup Call Divert Notification that a Call has been Diverted Call WaitingTo Remove Call Diversion To Check the Call Wait Status To Cancel Call WaitingTo Set Call Waiting Call Waiting In-Call Menu Switching between Active Call and Call on HoldDealing with Multiple Calls Placing a Second Call and holding the Current CallCall Termination by Calling Party with another Call Held Placing a Call when the Called Party is EngagedConference Calls To Create a Conference CallTo Review the Participants in a Conference Call Call Hold and Call Termination by a Remote Party Call Control Public MMI Commands SummaryTo Disconnect a Remote Party from a Conference Call Remote Party NotificationCall Barring To Check the Call Bar StatusTo Set Outgoing Call Barring To Set Incoming Call BarringTo Cancel Outgoing Call Barring To Cancel Incoming Call BarringTo Change the Network Password for Call Barring Receiving a Message Quick access to unread messagesSending And Receiving Text Messages Checking SubscriptionDeleting a Message To Read a MessageSaving and Dialling a Number Received in a Message To Select Message Tones Clearing Messages AutomaticallySending a Message Displaying Priority Messages ImmediatelyTo Originate a New Message To Enter Message Text To Enter the Service Centre NumberTo Enter the Destination Address To Review Your Newly Created Message To Enter the Validity PeriodTo Select the Message Type To Create a Message from an Existing MessageTo Return to the Current Message and complete it To Send the Completed MessageTo Save a Message To Delete a MessageTo Set the Message Parameter Defaults To Check on the Status of the Last Message SentWhat We Will Do WarrantyOur Warranty ConditionsPatents R290 User’s Guide Index PIN