Ericsson R290 manual To Check the Call Wait Status, To Set Call Waiting, To Cancel Call Waiting

Page 53

R290 User’s Guide

Only a voice call or voice calls may be placed on hold.

3. Press 2 for Set.

To Check the Call Wait Status

1.Press SOFT LEFT, 5 to enter Advanced menu.

2.Press 2 for Call Wait menu.

3.Press 1 for Status.

One of the following messages will appear:

All Call Wait Services Activated

Data Call Wait Activated

All Call Wait Services Inactive

Data Call Wait Not Activated

Voice Call Wait Activated

Fax Call Wait Activated

Voice Call Wait Not Activated

Fax Call Wait Not Activated

There may be a short delay before the network responds to the status request, this will be indicated by the message ‘ Please Wait’ being shown on the display.

Each response is shown for 4 seconds then the phone returns to stand-by.

To Set Call Waiting

1.Press SOFT LEFT, 5 to enter Advanced menu.

2.Press 2 for Call Wait menu.

4.Press 1 or YES to call wait all calls, 2 to call wait a call when the phone is engaged, 3 to call wait incoming calls if you are not available, 4 to call wait incoming calls when the phone is switched off.

5.Select the basic service group for which the Call Wait is to be set. The display will show:

6. Press 1 for All Calls, 2 for Voice Only, 3 for Data Only or 4 for Fax Only.

The message ‘ Please Wait’ will be shown on the display. When the network has responded, the message ‘ Request accepted’ will be shown, accompanied by the RADIO PATH ACKNOWLEDGEMENT TONE in the earpiece.

The phone will then return to the stand-by display.

To Cancel Call Waiting

1.Press SOFT LEFT, 5 to enter Advanced menu.

2.Press 2 for Call Wait menu.

3.Press 3 for Cancel.

4.Press 1 or YES to cancel call wait all calls, 2 to cancel call wait a call when the phone is engaged, 3 to cancel call wait incoming calls if

45

Image 53

Contents Ericsson R290 Satellite Innovatron Patents Guidelines for Safe and Efficient Use Safety InstructionsProduct Care and Maintenance Electronic Devices DrivingAircraft Blasting AreasBattery Information Please note Recycling Your BatteryContents Warranty Introduction Globalstar/GSM About Your PhoneOperators & Subscriptions SIM CardPhone Inserting the SIM Card Preparing Your Phone for UseOperating Without a SIM Card Charging the Battery BatteryR290 User’s Guide When to Charge the Battery Disconnecting the ChargerLow Battery Alarm AntennaUse with Mobile Office Globalstar Mode Use with Portable Hands Free Globalstar ModeTurning On the Phone Turning Off the PhoneTerms Used Display Text and SymbolsNavigating the Menu System Icon Function Indicators in the DisplayInitial Phone Settings Selecting a Network Searching for a NetworkStand-by display Making and Receiving Calls Answering a Call Receiving a CallRejecting a Call Calling Line Identification CLIHandling Two Calls Useful Information while Talking To Change Key Tone Volume To Change the Ring VolumeUsing Auto-Redial To Redial the Last Dialled NumberMaking/Answering a Call with Call Bar Active Missed CallsNotification that a Call has been Diverted To dial the last 10 numbers dialled, received or missedAbout the Phone Book Using the Phone BookInternational Numbers Speed DiallingTo Store a Name and a Number into a Selected Memory Store Upper Case ModeLower Case Mode To Edit a Number from Memory Store To Store Your Own Telephone NumberDialled Store To Display your Own Telephone NumberLast Number Stores Pause Dialling Last Number RedialReceived Store Missed StoreOne-Touch Dialling Sending Dtmf Tones During a CallCall Duration and Cost Last CallAll Calls To Reset the Call Time/Cost CountersCall Cost Setup To Setup the Unit Time for Calls ‘ Cost Limit Approaching’ being displayed To set the maximum costBusy Numbers Personalizing Your PhoneTo Complete a Ccbs Call Ring VolumeRing Tone Connect ID Escalating Ring VolumeCaller ID Auto Answer Automatic Display of Call TimeGreetings ClockDate Mode Clock ModeSet Time Set DateLanguage Mode Satellite Synchronisation ModeLanguage To Choose a LanguageBacklight Operation Power SaveVisual Indicator Usage Voice Mail Handsfree Automatic Shutdown TimerFixed Dialled Number Store About Locks Setting the Keypad LockProtecting Your Phone To unlock the keypad To Enable the Phone PINPhone Lock PIN To Change the Phone PIN To Disable the Phone PINUnblocking with Personal Unblocking Key PUK To change the SIM PIN To Enable the SIM PIN LockCard Lock SIM PIN Controlling Your Calls To Disable the SIM PIN LockCall Divert To Review the Call Divert StatusTo Setup Call Divert To Remove Call Diversion Call WaitingNotification that a Call has been Diverted To Set Call Waiting To Cancel Call WaitingTo Check the Call Wait Status Dealing with Multiple Calls Switching between Active Call and Call on HoldCall Waiting In-Call Menu Placing a Second Call and holding the Current CallConference Calls Placing a Call when the Called Party is EngagedCall Termination by Calling Party with another Call Held To Create a Conference CallTo Review the Participants in a Conference Call To Disconnect a Remote Party from a Conference Call Call Control Public MMI Commands SummaryCall Hold and Call Termination by a Remote Party Remote Party NotificationTo Check the Call Bar Status Call BarringTo Set Incoming Call Barring To Set Outgoing Call BarringTo Cancel Incoming Call Barring To Cancel Outgoing Call BarringTo Change the Network Password for Call Barring Sending And Receiving Text Messages Quick access to unread messagesReceiving a Message Checking SubscriptionSaving and Dialling a Number Received in a Message To Read a MessageDeleting a Message Clearing Messages Automatically To Select Message TonesTo Originate a New Message Displaying Priority Messages ImmediatelySending a Message To Enter the Destination Address To Enter the Service Centre NumberTo Enter Message Text To Select the Message Type To Enter the Validity PeriodTo Review Your Newly Created Message To Create a Message from an Existing MessageTo Save a Message To Send the Completed MessageTo Return to the Current Message and complete it To Delete a MessageTo Check on the Status of the Last Message Sent To Set the Message Parameter DefaultsOur Warranty WarrantyWhat We Will Do ConditionsPatents R290 User’s Guide Index PIN