Ericsson R290 manual Making and Receiving Calls

Page 22

R290 User’s Guide

Making and Receiving Calls

This chapter describes how to make and receive calls, in both Globalstar and GSM mode, how to make international and emergency calls, how to show or hide your phone number when calling, and how to handle two calls simultaneously.

Making a Call

1.Enter the area code and phone number. The phone number is shown in the display. If there are more than 12 digits entered, the number will wrap around to the line above. If more than 24 digits, the 1st digit onwards will be represented by a diamond symbol at the left of the screen. To erase a digit, press CLR. To erase the entire phone number, press and hold down CLR for a couple of seconds.

2.Press YES to make the call. The display shows ‘Calling’, followed by ‘Connected’ and the phone icon is lit.

Holding the Phone

Put the earpiece to your ear for optimum speech and reception quality. If the phone is operating in satellite mode, the satellite antenna must be deployed in the correct position for making a call, see “Deploying the Antenna” on page 7. Ensure the satellite antenna is kept vertical when in use. It is adjustable for left or right handed operation, and has a third position for use on a flat surface outdoors. This position is for use with a hands free kit or mobile office.

It is not necessary to deploy the antenna when making a GSM call. The GSM antenna is located inside the phone.

Ending a Call

Press NO to end a call.

Making an International Call

1.Press and hold the zero key until the international + prefix is displayed.

2.Enter the country code, area code (without any leading zero) and the phone number.

3.Press YES to make the call.

Making an Emergency Call

Enter 112 (The international emergency number) and press YES.

The 112 emergency number can be used in most countries with or without a SIM Card, provided a cellular network is within range. In Globalstar mode a SIM must be fitted.

Redial Function

If the call connection fails, press SOFT RIGHT to redial the number. Press NO to end the call. See “To Redial the Last Dialled Number” on page 18 and “Busy Numbers” on page 30 for more details on this option.

14

Image 22
Contents Ericsson R290 Satellite Innovatron Patents Product Care and Maintenance Safety InstructionsGuidelines for Safe and Efficient Use Aircraft DrivingElectronic Devices Blasting AreasBattery Information Recycling Your Battery Please noteContents Warranty Introduction Operators & Subscriptions About Your PhoneGlobalstar/GSM SIM CardPhone Operating Without a SIM Card Preparing Your Phone for UseInserting the SIM Card Battery Charging the BatteryR290 User’s Guide Low Battery Alarm Disconnecting the ChargerWhen to Charge the Battery AntennaTurning On the Phone Use with Portable Hands Free Globalstar ModeUse with Mobile Office Globalstar Mode Turning Off the PhoneNavigating the Menu System Display Text and SymbolsTerms Used Indicators in the Display Icon FunctionInitial Phone Settings Searching for a Network Selecting a NetworkStand-by display Making and Receiving Calls Rejecting a Call Receiving a CallAnswering a Call Calling Line Identification CLIHandling Two Calls Useful Information while Talking Using Auto-Redial To Change the Ring VolumeTo Change Key Tone Volume To Redial the Last Dialled NumberNotification that a Call has been Diverted Missed CallsMaking/Answering a Call with Call Bar Active To dial the last 10 numbers dialled, received or missedInternational Numbers Using the Phone BookAbout the Phone Book Speed DiallingUpper Case Mode To Store a Name and a Number into a Selected Memory StoreLower Case Mode To Store Your Own Telephone Number To Edit a Number from Memory StoreLast Number Stores To Display your Own Telephone NumberDialled Store Received Store Last Number RedialPause Dialling Missed StoreCall Duration and Cost Sending Dtmf Tones During a CallOne-Touch Dialling Last CallCall Cost Setup To Reset the Call Time/Cost CountersAll Calls To Setup the Unit Time for Calls To set the maximum cost ‘ Cost Limit Approaching’ being displayedPersonalizing Your Phone Busy NumbersRing Tone Ring VolumeTo Complete a Ccbs Call Caller ID Escalating Ring VolumeConnect ID Greetings Automatic Display of Call TimeAuto Answer ClockSet Time Clock ModeDate Mode Set DateLanguage Satellite Synchronisation ModeLanguage Mode To Choose a LanguageVisual Indicator Usage Power SaveBacklight Operation Fixed Dialled Number Store Handsfree Automatic Shutdown TimerVoice Mail Protecting Your Phone Setting the Keypad LockAbout Locks Phone Lock PIN To Enable the Phone PINTo unlock the keypad Unblocking with Personal Unblocking Key PUK To Disable the Phone PINTo Change the Phone PIN Card Lock SIM PIN To Enable the SIM PIN LockTo change the SIM PIN Call Divert To Disable the SIM PIN LockControlling Your Calls To Review the Call Divert StatusTo Setup Call Divert Notification that a Call has been Diverted Call WaitingTo Remove Call Diversion To Check the Call Wait Status To Cancel Call WaitingTo Set Call Waiting Call Waiting In-Call Menu Switching between Active Call and Call on HoldDealing with Multiple Calls Placing a Second Call and holding the Current CallCall Termination by Calling Party with another Call Held Placing a Call when the Called Party is EngagedConference Calls To Create a Conference CallTo Review the Participants in a Conference Call Call Hold and Call Termination by a Remote Party Call Control Public MMI Commands SummaryTo Disconnect a Remote Party from a Conference Call Remote Party NotificationCall Barring To Check the Call Bar StatusTo Set Outgoing Call Barring To Set Incoming Call BarringTo Cancel Outgoing Call Barring To Cancel Incoming Call BarringTo Change the Network Password for Call Barring Receiving a Message Quick access to unread messagesSending And Receiving Text Messages Checking SubscriptionDeleting a Message To Read a MessageSaving and Dialling a Number Received in a Message To Select Message Tones Clearing Messages AutomaticallySending a Message Displaying Priority Messages ImmediatelyTo Originate a New Message To Enter Message Text To Enter the Service Centre NumberTo Enter the Destination Address To Review Your Newly Created Message To Enter the Validity PeriodTo Select the Message Type To Create a Message from an Existing MessageTo Return to the Current Message and complete it To Send the Completed MessageTo Save a Message To Delete a MessageTo Set the Message Parameter Defaults To Check on the Status of the Last Message SentWhat We Will Do WarrantyOur Warranty ConditionsPatents R290 User’s Guide Index PIN