Ericsson R290 manual Call Barring, To Check the Call Bar Status

Page 58

R290 User’s Guide

2 YES This accepts the waiting call and puts the active call on hold.

2X YES This puts all active calls on hold except call X with which communication shall be supported (used in conference calls).

3 YES Adds a held call to the conversation (i.e. merges the active and held calls to form or add to a conference call).

4 YES This merges the active and held calls to perform a call transfer.

5 YES Activate a CCBS request for the last dialled number. This must be done before 15s have elapsed after the end of the call.

NO This ends all active and held calls, but not those that are waiting.

Tel No. YES This places the active call on hold and sets up a new call to the telephone number dialled.

Call Barring

The call barring service lets you control which kind of calls can be made to or from your phone. This feature is convenient if you lend your phone to somebody else. This feature is service dependent.

To Check the Call Bar Status

1.Press SOFT LEFT, 5 to enter Advanced menu.

2.Press 3 for Call Bar menu.

3. Press 1 for Status.

4.Press 1 to review the Outgoing Call Bar Status. The network will respond with one of the following messages:

No Outgoing Call Restrictions

All Services Barred Emergency Calls Only Voice Calls Barred Emergency Calls Only Messages Barred

Data Calls Barred Fax Calls Barred Internat’l Services Barred Internat’l Voice Calls Barred Internat’l Messages Barred Internat’l Data Calls Barred Internat’l Fax Calls Barred

Internat’l Services Barred Except (Home Country) Internat’l Voice Calls Barred Except (Home Country) Internat’l Messages Barred Except (Home Country) Internat’l Data Calls Barred Except (Home Country) Internat’l Fax Calls Barred Except (Home Country)

If more than one restriction is set, you can scroll through the messages one by one using the SOFT keys. Alternatively, the network may respond with a notification message for an unsupported service.

5. If you had pressed 2 the following messages would display:

No Incoming Call Restrictions

All Incoming Services Barred

All Incoming Services Barred When Roaming

50

Image 58
Contents Ericsson R290 Satellite Innovatron Patents Product Care and Maintenance Safety InstructionsGuidelines for Safe and Efficient Use Aircraft DrivingElectronic Devices Blasting AreasBattery Information Recycling Your Battery Please noteContents Warranty Introduction Operators & Subscriptions About Your PhoneGlobalstar/GSM SIM CardPhone Operating Without a SIM Card Preparing Your Phone for UseInserting the SIM Card Battery Charging the BatteryR290 User’s Guide Low Battery Alarm Disconnecting the ChargerWhen to Charge the Battery AntennaTurning On the Phone Use with Portable Hands Free Globalstar ModeUse with Mobile Office Globalstar Mode Turning Off the PhoneNavigating the Menu System Display Text and SymbolsTerms Used Indicators in the Display Icon FunctionInitial Phone Settings Searching for a Network Selecting a NetworkStand-by display Making and Receiving Calls Rejecting a Call Receiving a CallAnswering a Call Calling Line Identification CLIHandling Two Calls Useful Information while Talking Using Auto-Redial To Change the Ring VolumeTo Change Key Tone Volume To Redial the Last Dialled NumberNotification that a Call has been Diverted Missed CallsMaking/Answering a Call with Call Bar Active To dial the last 10 numbers dialled, received or missedInternational Numbers Using the Phone BookAbout the Phone Book Speed DiallingUpper Case Mode To Store a Name and a Number into a Selected Memory StoreLower Case Mode To Store Your Own Telephone Number To Edit a Number from Memory StoreLast Number Stores To Display your Own Telephone NumberDialled Store Received Store Last Number RedialPause Dialling Missed StoreCall Duration and Cost Sending Dtmf Tones During a CallOne-Touch Dialling Last CallCall Cost Setup To Reset the Call Time/Cost CountersAll Calls To Setup the Unit Time for Calls To set the maximum cost ‘ Cost Limit Approaching’ being displayedPersonalizing Your Phone Busy NumbersRing Tone Ring VolumeTo Complete a Ccbs Call Caller ID Escalating Ring VolumeConnect ID Greetings Automatic Display of Call TimeAuto Answer ClockSet Time Clock ModeDate Mode Set DateLanguage Satellite Synchronisation ModeLanguage Mode To Choose a LanguageVisual Indicator Usage Power SaveBacklight Operation Fixed Dialled Number Store Handsfree Automatic Shutdown TimerVoice Mail Protecting Your Phone Setting the Keypad LockAbout Locks Phone Lock PIN To Enable the Phone PINTo unlock the keypad Unblocking with Personal Unblocking Key PUK To Disable the Phone PINTo Change the Phone PIN Card Lock SIM PIN To Enable the SIM PIN LockTo change the SIM PIN Call Divert To Disable the SIM PIN LockControlling Your Calls To Review the Call Divert StatusTo Setup Call Divert Notification that a Call has been Diverted Call WaitingTo Remove Call Diversion To Check the Call Wait Status To Cancel Call WaitingTo Set Call Waiting Call Waiting In-Call Menu Switching between Active Call and Call on HoldDealing with Multiple Calls Placing a Second Call and holding the Current CallCall Termination by Calling Party with another Call Held Placing a Call when the Called Party is EngagedConference Calls To Create a Conference CallTo Review the Participants in a Conference Call Call Hold and Call Termination by a Remote Party Call Control Public MMI Commands SummaryTo Disconnect a Remote Party from a Conference Call Remote Party NotificationCall Barring To Check the Call Bar StatusTo Set Outgoing Call Barring To Set Incoming Call BarringTo Cancel Outgoing Call Barring To Cancel Incoming Call BarringTo Change the Network Password for Call Barring Receiving a Message Quick access to unread messagesSending And Receiving Text Messages Checking SubscriptionDeleting a Message To Read a MessageSaving and Dialling a Number Received in a Message To Select Message Tones Clearing Messages AutomaticallySending a Message Displaying Priority Messages ImmediatelyTo Originate a New Message To Enter Message Text To Enter the Service Centre NumberTo Enter the Destination Address To Review Your Newly Created Message To Enter the Validity PeriodTo Select the Message Type To Create a Message from an Existing MessageTo Return to the Current Message and complete it To Send the Completed MessageTo Save a Message To Delete a MessageTo Set the Message Parameter Defaults To Check on the Status of the Last Message SentWhat We Will Do WarrantyOur Warranty ConditionsPatents R290 User’s Guide Index PIN