Ericsson R290 manual Personalizing Your Phone, Busy Numbers

Page 38

R290 User’s Guide

If using a Phase 1 SIM, any attempt to access the Cost results in the message ‘ Request Rejected’ being displayed.

If you enter the SUPER PIN incorrectly three times, the SUPER PIN will be blocked and you will be unable to use the SUPER PIN protected features.

NOTE:

The call charge indications provided by the phone are only an approximation of the true cost of your calls as determined by your service provider. These will be accurate if you have subscribed to Advice of Charge, as the phone will calculate call charges using the cost entered and time units supplied by the Advice of Charge Information (AOCI) and/or Advice of Charge Charging (AOCC).

Personalizing Your Phone

Busy Numbers

This menu allows you to select the action the phone will take if you dial a number that is busy or unobtainable. The auto-redial feature permits a telephone number to be redialled if the call does not connect at the first attempt. If your subscription supports the GSM Completion of Calls to Busy Subscribers (CCBS) service a network request can be sent.

1.Press SOFT LEFT, 1, 1 to enter Call Setup menu.

2.Press 1 or YES to show Busy Numbers menu.

3. Select required function:

•To enable the auto redial, press 1.

•To enable the CCBS, press 2.

•To disable both the auto-redial and CCBS, press 3.

A confirmation message will be displayed for 2 seconds.

30

Image 38

Contents Ericsson R290 Satellite Innovatron Patents Guidelines for Safe and Efficient Use Safety InstructionsProduct Care and Maintenance Aircraft DrivingElectronic Devices Blasting AreasBattery Information Recycling Your Battery Please noteContents Warranty Introduction Operators & Subscriptions About Your PhoneGlobalstar/GSM SIM CardPhone Inserting the SIM Card Preparing Your Phone for UseOperating Without a SIM Card Battery Charging the BatteryR290 User’s Guide Low Battery Alarm Disconnecting the ChargerWhen to Charge the Battery AntennaTurning On the Phone Use with Portable Hands Free Globalstar ModeUse with Mobile Office Globalstar Mode Turning Off the PhoneTerms Used Display Text and SymbolsNavigating the Menu System Indicators in the Display Icon FunctionInitial Phone Settings Searching for a Network Selecting a NetworkStand-by display Making and Receiving Calls Rejecting a Call Receiving a CallAnswering a Call Calling Line Identification CLIHandling Two Calls Useful Information while Talking Using Auto-Redial To Change the Ring VolumeTo Change Key Tone Volume To Redial the Last Dialled NumberNotification that a Call has been Diverted Missed CallsMaking/Answering a Call with Call Bar Active To dial the last 10 numbers dialled, received or missedInternational Numbers Using the Phone BookAbout the Phone Book Speed DiallingUpper Case Mode To Store a Name and a Number into a Selected Memory StoreLower Case Mode To Store Your Own Telephone Number To Edit a Number from Memory StoreDialled Store To Display your Own Telephone NumberLast Number Stores Received Store Last Number RedialPause Dialling Missed StoreCall Duration and Cost Sending Dtmf Tones During a CallOne-Touch Dialling Last CallAll Calls To Reset the Call Time/Cost CountersCall Cost Setup To Setup the Unit Time for Calls To set the maximum cost ‘ Cost Limit Approaching’ being displayedPersonalizing Your Phone Busy NumbersTo Complete a Ccbs Call Ring VolumeRing Tone Connect ID Escalating Ring VolumeCaller ID Greetings Automatic Display of Call TimeAuto Answer ClockSet Time Clock ModeDate Mode Set DateLanguage Satellite Synchronisation ModeLanguage Mode To Choose a LanguageBacklight Operation Power SaveVisual Indicator Usage Voice Mail Handsfree Automatic Shutdown TimerFixed Dialled Number Store About Locks Setting the Keypad LockProtecting Your Phone To unlock the keypad To Enable the Phone PINPhone Lock PIN To Change the Phone PIN To Disable the Phone PINUnblocking with Personal Unblocking Key PUK To change the SIM PIN To Enable the SIM PIN LockCard Lock SIM PIN Call Divert To Disable the SIM PIN LockControlling Your Calls To Review the Call Divert StatusTo Setup Call Divert To Remove Call Diversion Call WaitingNotification that a Call has been Diverted To Set Call Waiting To Cancel Call WaitingTo Check the Call Wait Status Call Waiting In-Call Menu Switching between Active Call and Call on HoldDealing with Multiple Calls Placing a Second Call and holding the Current CallCall Termination by Calling Party with another Call Held Placing a Call when the Called Party is EngagedConference Calls To Create a Conference CallTo Review the Participants in a Conference Call Call Hold and Call Termination by a Remote Party Call Control Public MMI Commands SummaryTo Disconnect a Remote Party from a Conference Call Remote Party NotificationCall Barring To Check the Call Bar StatusTo Set Outgoing Call Barring To Set Incoming Call BarringTo Cancel Outgoing Call Barring To Cancel Incoming Call BarringTo Change the Network Password for Call Barring Receiving a Message Quick access to unread messagesSending And Receiving Text Messages Checking SubscriptionSaving and Dialling a Number Received in a Message To Read a MessageDeleting a Message To Select Message Tones Clearing Messages AutomaticallyTo Originate a New Message Displaying Priority Messages ImmediatelySending a Message To Enter the Destination Address To Enter the Service Centre NumberTo Enter Message Text To Review Your Newly Created Message To Enter the Validity PeriodTo Select the Message Type To Create a Message from an Existing MessageTo Return to the Current Message and complete it To Send the Completed MessageTo Save a Message To Delete a MessageTo Set the Message Parameter Defaults To Check on the Status of the Last Message SentWhat We Will Do WarrantyOur Warranty ConditionsPatents R290 User’s Guide Index PIN