Ericsson LBI-38965B installation manual Hardware Installation

Page 20

LBI-38965

INSTALLATION

4. INSTALLATION

4.1. HARDWARE INSTALLATION

CAUTION

Turn off the power before removing or installing VMEbus boards. Removing or reinstalling the boards while the power is on will damage the boards.

This section describes the physical installation of the BCU/CAL. Other configuration is performed during manufacture, and the information necessary is provided in Appendix B.

Follow these steps to connect a BCU/CAL to an IMC for the first time (except where indicated otherwise, these steps apply to all configurations; BCU only, CAL only, or BCU and CAL):

Using the LAPB cable provided, connect the BCU/CAL's CAM control port 0, a female DB-25 connector located on the rear of the BCU enclosure, to the lower connector on the IMC backplane which corresponds to the slot in which the CAM resides. The cable is keyed so that it fits properly only when it is correctly oriented.

BCU/CAL Equipment Rack

A6 2203710G1			19C852327G1
BCU/CAL
				J1



CAM Control				J14
Port 0				J14
Port 0

Data Concentrator at

BCU/CAL Equipment Rack

IMC Equipment Rack

	19D903531P1			19D903628P71
	19D903531P1					P72
		P2		P1		P73
	J1	P2		P1		P73
						CAM Control


	J9			This will be plugged into
				PA2XX on the backplane
				and will correspond with
				the slot in which the CAM
	Audio Concentrator			the slot in which the CAM
	Audio Concentrator			control card is located.

at IMC

19D903880P120-129

Figure 5 - BCU/CAL to IMC

Next, connect the console terminal to the female DB-25 connector labeled "SERIAL PORT 1/CONSOLE" on the TVME-712/M transition module located in the rear of the BCU/CAL enclosure. (For reference, the BCU/CAL is delivered preconfigured from the factory in a 19-inch rack.) Connect the other end of this cable to the console terminal's "host" port, or equivalent. If a PC is used as the console terminal, then a DB-9 adapter may be needed. In either case, the serial cable for the console is wired straight-through.

Configure the console terminal for the communications parameters below.

∙9600 Baud

∙No Parity

∙8 Data Bits

∙1 Stop Bit

20

Image 20

Contents Ericssonz LBI-38965 Table of Contents Table of Contents Introduction BCU/CAL ArchitectureCall Types Supported BCU Functional DescriptionCAL Functional Description Introduction Physical Specifications Physical Description and CompatibilityBCU/CAL Architecture TVME147 CPUCPU Compatibility Backwards CompatibilityBCU Operational Specifications SpecificationsCommon BCU and CAL Operational Specifications Billing Architecture Billing Architecture BCU Operation OverviewGroup Billing Mode RF Channel Usage Air TimeConversations Grouping CallsContents File NameDefault Data Operator FunctionsDatabase Elements Unit DataCDR Processing Errors Call ProcessingCDR Processing Call Processing CDR OutputProtocol Supported CAL Operational SpecificationsSystem Manager Interface Additional Product Features Network File System CAL Operation OverviewInstallation Hardware InstallationSoftware Installation Distribution MediaInstallation Diskette UsageROUTES.DAT Configuration File ParameterIP.DAT File Parameters MeaningEXPORTS.DAT Configuration File Directory clientip EXPORTS.DAT File ParametersCAL.DAT Configuration File CAL.DAT File ParametersInitial Installation PrerequisitesInstallation Installation User Information Default System Accounts LoginPassword Access LevelPrerequisite User Information Entering bcs invokes the BCS programSystem Disk Booting User Information Invoke the BCS program Software UpgradesProper System Shutdown CAL Terminal Server Configuration # accessConfiguration Tips ExampleThis page intentionally left blank Appendix a Edacs Billing CDR Format Overview Billing by ConversationBilling for Multiple Sites Record EncodingRecord Layout SINGLE-SITE CallsMULTIPLE-SITE Calls CDR Radix-64 DigitMOBILE-TO-LAND Telephone Interconnect Calls Table A.1 Call Detail Record Field DescriptionsCall Type Definitions Call Type Hex DecimalTable A.2 Call Types DescriptionDescription Valid with Rec. Type A0-FF Call Type Bit Fields Table A.3 Call Type Bit Field DefinitionsCDR File Topics Page Appendix B Physical Configuration Details Jumper Settings Figure B.1 Tvme 147SA1 Single-Board Computer Figure B.2 Tvme 712/M Transition Module Figure B.4 fv5310 Main Board Figure B.5 fv5310 Mezzanine Card Scsi Connector Pwr Connector DB-25F Signal Name Cable PinoutsTable B.1 WANServer Port FunctionTable B.2 WANServer Port Table B.3 WANServer Port Table B.4 WANServer Port Table B.5 BCU/CAL Hdlc Loopback Cable Specification DB-25M Connector M/W BCU/CAL Port Signal NameFigure B.9 CAL Terminal Server to Distribution Panel Cable Figure B.10 CAL 32-Port Configuration Computer Terminal Appendix C Fault Tolerance Figure C.1 Edacs Billing Fault Tolerant Architecture Redundant Operation