JVC UX-J99DVD manual Basic and Common Operations, Setting the Clock

Page 13

Basic and Common Operations

English

Setting the Clock

Before operating the unit any further, first set the built-in clock. When you plug in the power cord, “0:00” starts flashing on the display.

You can set the clock when the unit is either turned on or on standby (off). You cannot set the clock if the unit is on Power Save mode (see the right column).

On the remote control ONLY:

1 Press CLOCK/TIMER.

The hour digit starts flashing on the display.

2 Press cursor 3 or 2 repeatedly to adjust the hour, then press SET.

The minute digits start flashing on the display.

• Each time you press 3 or 2, the hour digit(s) change(s) continuously.

•If you want to correct the hour again, press CANCEL. The hour digit(s) start(s) flashing again.

3 Press cursor 3 or 2 to adjust the minute, then press SET.

The built-in clock starts.

• Each time you press cursor 3 or 2, the minute digits change continuously.

•When you unplug the power cord or if a power failure occurs

The clock is reset to “0:00” right away. If this happens, set the clock again.

•The clock may gain or lose 1 to 2 minutes per month If this happens, reset the clock.

To change the clock again

On the remote control ONLY:

Press CLOCK/TIMER repeatedly until the clock setting screen appears on the display.

The hour digit starts flashing. Then, perform steps 2 and

3in “Setting the Clock” again.

To turn off the clock indication (Power Save)

On the remote control ONLY:

Press DISP/CHARA while the unit is on standby (off).

“DISPLAY OFF” appears on the display for a while, then the clock indication goes off.

To turn on the clock indication, press DISP/CHARA again while the unit is on standby (off).

“DISPLAY ON” appears on the display for a while.

Turning On the Power and Starting Playback

To turn on the unit, press AUDIO or on the unit. The STANDBY/ON lamp on the unit lights green.

 

STANDBY/ON

(On the remote control)

(On the unit)

When you press one of the source selection buttons, the unit automatically turns on (and starts playback if the source is ready).

(On the remote control)

DISC

0

0

AUX

SELECT

 

 

‹/8

‹/8

¤ ‹

FM/AM

DVD

MD

TAPE

 

(On the unit)

•Pressing one of the disc eject buttons on the unit—DISC10to DISC50, 0 (MD eject) and 0 (TAPE eject)—also turns on the unit if the disc trays, MD, and cassette are unlocked.

•Press FM/AM/AUX repeatedly (or AUX on the unit) to select “AUX” or “AUX-DIGITAL” to operate the external equipment, see page 44 and the manuals supplied with it.

To turn off the unit (on standby), press AUDIO or on the

unit again.

The STANDBY/ON lamp on the unit lights red.

•The clock time appears on the display if you have set the built-in clock.

“0:00” will flash on the display if you have not set the built-in clock.

To set the built-in clock, see “Setting the Clock” on the left column.

•A little power is always consumed even while the unit is on standby (off).

To switch off the power supply completely, unplug the AC power

cord from the AC outlet.

When you unplug the AC power cord or if a power failure occurs

The clock is reset to “0:00” right away, while the tuner preset stations will be erased in a few days.

10

Page 12 Page 14
Image 13
Page 12 Page 14
Contents UX-J99DVD Page Important for Laser Products Introduction PrecautionsAbout This Manual Contents Remote Control Remote ControlLocation of the Buttons and Controls Become familiar with the buttons and controls on your unitFront panel Front PanelDisc trays compartment-5-DVD changer Reverse mode indicator Group indicatorDisplay window on the front panel Display windowGetting Started Connecting AntennasUnpacking Attach the FM antenna to the FM 75 Ω Coaxial terminalTo connect an outdoor FM antenna Connecting SpeakersAM antenna To connect an outdoor AM antennaRelease your finger from the clamp Connecting a TVTo remove the speaker grilles Color system of TV Color system setting Connecting Other EquipmentTo select the color system To connect analog audio equipmentTurning On the Power and Starting Playback Setting the ClockBasic and Common Operations To turn down the volume level temporarily Adjusting the Volume LevelReinforcing the Bass Sound Press Fade MutingChanging the Scanning Mode Adjusting the ToneChanging the Display Brightness Press Dimmer while the unit is turned onListening to FM and AM Broadcasts Setting the AM Tuner Interval SpacingTuning in to a Preset Station Presetting StationsDisc Information Playing Back Discs on the 5-DVD ChangerPlayable disc types About copy protectionPlayback Control function PBC-SVCD and VCD only Disc structurePlaying Back All the Discs-Continuous Play Loading DiscsLoad discs into the 5-DVD changer Press GROUP/TITLE I or GROUP/TITLE I during playback Basic Disc OperationsPress ¢ or 4 during playback Press ¡ or Using the number buttonsPress ¢ or 4 repeatedly Press DISP/CHARAWhen playing a DVD Playing Back by Using the Disc MenuWhen playing a Svcd or VCD Press TOP Menu or MenuPress the number buttons to select a disc tray Programing the Track Playing Order Program PlayProgram other tracks you want Press DVDPlaying at Random-Random Play To check the programed contentsTo exit from Program Play To modify the programProhibiting Disc Ejection-Disc Lock Repeating Playback-Repeat PlayPress Repeat To exit from Random PlayAbout the On-screen Bar Advanced Disc OperationsPress on Screen Indication Meanings Available discsPress on Screen twice Operation through the On-screen BarPress Enter On-screen guide iconsRepeating Playback Press cursor ∞/5 repeatedly to select Repeat Play modeTo repeat a current title, group, chapter, or all tracks To repeat a desired portion-A-B Repeat Press cursor ∞/5 repeatedly to select A-BLocating a desired position-Time Search While playing back a DVDLocating a desired chapter/track Ex. When playing a DVD AudioTo correct a misentry Unit starts playback from the specified timeSelecting the Subtitle Language Selecting the Audio LanguagePress Audio Press Audio repeatedly to select the desired audio languageSelecting Browsable Still Pictures recorded on Selecting a View AnglePress Angle Press Angle repeatedly to select the desired view anglePress Audio repeatedly to select the desired audio channel Press Virtual SurroundEx. ST 1 ST 2 L 1 R 1 L 2 R ST 1/STPress 8 once Special Picture PlaybackPress 8 repeatedly Press Slow 9 ¡ orPress cursor 3/2 repeatedly to select the VFP mode Changing the VFP SettingRepeat steps 2 to 4 to adjust other parameters Press VFPSelect a bonus group Playing Back a Bonus GroupWhile the key number entry indication appears On the display On the TV screenPress DVD 8 or #¥8 DVD on the unit MP3/JPEG Disc PlaybackPress ¢ / 4 repeatedly as many times as required Press cursor ∞/5 repeatedly to select a group Operations through the MP3/JPEG Control ScreensPress DVD 3 or Enter Press Repeat during or before playPlaying Back the Entire MD Normal Play Playing Back an MDBasic MD Operations While playing or pausing To go to another track directly using the number buttonsRecording length mode To change the information shown on the displayLoad an MD To check the program contentsPress the number buttons to select the tracks Repeat to program other tracks you wantLoad an MD including groups Playing Tracks in a Group-Group PlayPress GROUP/TITLE I or GROUP/TITLE I to select a group Press Repeat repeatedly during or before play Press Title SearchEnter the characters to search for the track title MD Repeat ALLTo prohibit MD ejection-MD Lock Playing Back a Tape Playing Back a TapePress REV.MODE Press Tape 2Listening to External Equipment Turn down the volume level to Volume MINListening to External Equipment Press AUXBefore You Start Recording on an MD Recording on an MDAbout the track marks To avoid erasing important recordingsPress LP Setting MD Recording ModesPress Group REC ON/OFF When recording from a CD-R/RW Press CD REC Mode to select the recording modeRecording discs onto an MD Disc-MD Synchronized Recording Press REC Speed to select the recording speed you wantPrepare the source to record from Recording Other Sources onto an MDTo record a single track during play or pause REC MD recording indicator starts flashing On the display Press TR. Mark Select to select track mark entry modeManual Mark Time Auto Mark Before You Start Recording on a Tape Recording on a TapeTo protect your recordings To keep the best recording and playback sound qualityPress Tape REC Recording onto a TapeWhen recording a disc or an MD Press REV.MODE to select a reverse modeRecording Disc onto a Tape Disc-Tape Synchronized Recording To record from the desired trackWhen recording on an MD and a tape at the same time MD and tape Elapsed Recording indicatorsRecording Discs onto an MD and a Tape Disc Synchronized RecordingHow to make up Groups Using MD Groups as a separate itemEditing an MD Guidance-MD Group FunctionsGroup Introducing Group Editing Functions13 14 Forming a Group-FORM GR When Cannot FORM! appears on the display in stepInsert an MD you want to edit into the MD loading slot During playbackAdding a Track to a Group-ENTRY GR When Cannot ENTRY! appears on the display in stepPress UP ¢ or Down 4 to select the track Press GROUP/TITLE I or GROUP/TITLE I to select the groupDividing a Group-DIVIDE GR Ex. When track 18 is selectedEx. When groups 7 and 8 are selected When Cannot Join appears on the display in stepJoining Two Groups-JOIN GR Ex. When group 3 is moved to group Ex. When group 3 is selectedMoving a Group-MOVE GR Dissolving All Groups-UNGR ALL Ungrouping Tracks-UNGROUPInsert an MD you want to edit into the MD Loading slotErasing Tracks in a Group-ERASE GR Ex. When group 6 is selectedIntroducing Track Editing Functions Ex. When track 12 is selected Ex. When adjusting the point byDividing a Track-DIVIDE Press UP ¢ or Down 4 to select the track you want to divideJoining Two Tracks-JOIN Ex. When tracks 2 and 3 are selectedMoving a Track-MOVE Ex. When track 3 is moved to trackPress UP ¢ or Down 4 to select the track you want to move Erasing All Tracks-ALL Erase Erasing Tracks-ERASEYou can select up to 15 tracks Appears on the display Track marked with Will be erasedPress UP ¢ or Down 4 to change the title entry mode Enter the unit into the title entry modeAssigning Titles to an MD Press Title EditEnter characters Press Cancel to exit from the title entry modePress Enter to finish the current title entry Press 0 MD eject on the unit to ejectYou can assign titles during play or recording To Change the TitleYou can make a correction or change the title Make sure that the character you want to change is flashingUsing Recording Timer Using the TimersSet the shut-off time Set the start timeTo turn on the Recording Timer again To turn off the Recording Timer after its setting is doneSelect the device to record onto MD REC Tape RECHow Daily Timer actually works Using Daily TimerSelect the source to play back Select the fade setting Adjust the volume levelTimer Priority Using Sleep TimerHow Sleep Timer actually works Press Sleep repeatedlyConfiguration of the choice menus Initial Setting Using Choice MenuIntroducing the Choice Menus Operation buttonsPress Enter to finish the setting Operating ProcedurePress Choice Press cursor 3/2 repeatedly to display the Picture menuLanguage selection menu-LANGUAGE Picture setting menu-PICTUREDynamic Range Compression Other setting menu-OTHERSSetting Parental Lock Restricting the Access Level-Parental LockRemember your password or make a note of it When you enter wrong password three times Changing the Parental Lock settingReleasing Parental Lock temporarily To return to Others menuCountry/Area codes list for Parental Lock Set the AUDIO-TV switch to TV Press and hold TV Changing the Preset Signal CodesOperating Other Manufacturers’ TV Release TV Press TV to operate your TVConnection diagram Using AV Compu Link Control SystemAV Compu Link connection Available operationsGlossary Cleaning the unit MaintenanceGeneral Notes Handling discsAdditional Information Utoc User Table Of ContentsMD Disc Types Atrac Adaptive TRansform Acoustic Coding/ATRAC3Scms Serial Copy Management System Language Code List1st Generation MD limitationsCD with DTS Digital Surround MP3 disc Output Signals Output Signals through the DVD Optical Digital OUT TerminalDisc/MD Messages For DiscX1 only For MDSymptom TroubleshootingTuner Section Supplied accessoriesCassette deck Section GeneralEN, CS Victor Company of JAPAN, Limited 1203AIMMDWJEM
Top Page Image Contents