JVC UX-J99DVD manual Operating Other Manufacturers’ TV, Changing the Preset Signal Codes

Page 86

English

Operating Other Manufacturers’ TV

Changing the Preset Signal Codes

To operate JVC or other manufacturers’ TV using this remote control:

•Aim the remote control directly at the remote sensor on each equipment.

•Refer also to the manuals supplied with your equipment.

To change the transmittable signals for operating other manufacturers’ TV

1 Set the AUDIO-TV switch to “TV.”

2 Press and hold TV.

• You need to keep pressing until finishing step 5.

3 Press ENTER.

4 Enter the manufacturer’s code using the number buttons (0 – 9).

See the table on the right to find the code.

5 Release TV.

6 Press TV to operate your TV.

If your TV turns on or off, you have entered the correct code.

You can always perform the following operations with buttons listed below:

TV	Turns on or off the TV.
TV VOL +/–	Adjusts the TV volume.

TV CHANNEL +/– Changes the TV channels.

TV/VIDEO	Sets the input mode (either TV or
	VIDEO).

After setting the AUDIO-TV switch to “TV,” you can perform the following operations on a TV with buttons below:

1 – 9, 0, 100+	Selects the TV channels.
	For channel number 5, press 5.

For channel number 10, press 1, then 0. For channel number 23, press 2, then 3. For channel number 135, press 100+, 3, then 5.

•TV RETURN will function as the ENTER button if your equipment requires pressing ENTER after selecting a channel number.

•Refer also to the manual supplied for your TV.

•Not all of the functions listed on the left may be assigned to specific buttons for some TVs.

•If you cannot change the channels of some TVs by pressing the number buttons, press CHANNEL + or – for changing the channels.

If there is more than one code listed for your brand of TV

Try each one of the manufacturer’s code until the correct one is entered.

Manufacturer’s code

Manufacturer	Codes

JVC	01*

Hitachi	10

Magnavox	02

Mitsubishi	03

Panasonic	04, 11

RCA	05

Samsung	12

Sanyo	13

Sharp	06

Sony	07

Toshiba	08

Zenith	09

* “01” is the initial code.

•Manufacturers’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.

83

Image 86

Contents UX-J99DVD Page Important for Laser Products About This Manual PrecautionsIntroduction Contents Location of the Buttons and Controls Remote ControlRemote Control Become familiar with the buttons and controls on your unitDisc trays compartment-5-DVD changer Front PanelFront panel Display window on the front panel Group indicatorReverse mode indicator Display windowUnpacking Connecting AntennasGetting Started Attach the FM antenna to the FM 75 Ω Coaxial terminalAM antenna Connecting SpeakersTo connect an outdoor FM antenna To connect an outdoor AM antennaTo remove the speaker grilles Connecting a TVRelease your finger from the clamp To select the color system Connecting Other EquipmentColor system of TV Color system setting To connect analog audio equipmentBasic and Common Operations Setting the ClockTurning On the Power and Starting Playback Reinforcing the Bass Sound Adjusting the Volume LevelTo turn down the volume level temporarily Press Fade MutingChanging the Display Brightness Adjusting the ToneChanging the Scanning Mode Press Dimmer while the unit is turned onSetting the AM Tuner Interval Spacing Listening to FM and AM BroadcastsPresetting Stations Tuning in to a Preset StationPlayable disc types Playing Back Discs on the 5-DVD ChangerDisc Information About copy protectionDisc structure Playback Control function PBC-SVCD and VCD onlyLoad discs into the 5-DVD changer Loading DiscsPlaying Back All the Discs-Continuous Play Press ¢ or 4 during playback Basic Disc OperationsPress GROUP/TITLE I or GROUP/TITLE I during playback Press ¢ or 4 repeatedly Using the number buttonsPress ¡ or Press DISP/CHARAWhen playing a Svcd or VCD Playing Back by Using the Disc MenuWhen playing a DVD Press TOP Menu or MenuProgram other tracks you want Programing the Track Playing Order Program PlayPress the number buttons to select a disc tray Press DVDTo exit from Program Play To check the programed contentsPlaying at Random-Random Play To modify the programPress Repeat Repeating Playback-Repeat PlayProhibiting Disc Ejection-Disc Lock To exit from Random PlayPress on Screen Advanced Disc OperationsAbout the On-screen Bar Indication Meanings Available discsPress Enter Operation through the On-screen BarPress on Screen twice On-screen guide iconsTo repeat a current title, group, chapter, or all tracks Press cursor ∞/5 repeatedly to select Repeat Play modeRepeating Playback Locating a desired position-Time Search Press cursor ∞/5 repeatedly to select A-BTo repeat a desired portion-A-B Repeat While playing back a DVDTo correct a misentry Ex. When playing a DVD AudioLocating a desired chapter/track Unit starts playback from the specified timePress Audio Selecting the Audio LanguageSelecting the Subtitle Language Press Audio repeatedly to select the desired audio languagePress Angle Selecting a View AngleSelecting Browsable Still Pictures recorded on Press Angle repeatedly to select the desired view angleEx. ST 1 ST 2 L 1 R 1 L 2 R Press Virtual SurroundPress Audio repeatedly to select the desired audio channel ST 1/STPress 8 repeatedly Special Picture PlaybackPress 8 once Press Slow 9 ¡ orRepeat steps 2 to 4 to adjust other parameters Changing the VFP SettingPress cursor 3/2 repeatedly to select the VFP mode Press VFPWhile the key number entry indication appears Playing Back a Bonus GroupSelect a bonus group On the display On the TV screenPress ¢ / 4 repeatedly as many times as required MP3/JPEG Disc PlaybackPress DVD 8 or #¥8 DVD on the unit Press DVD 3 or Enter Operations through the MP3/JPEG Control ScreensPress cursor ∞/5 repeatedly to select a group Press Repeat during or before playBasic MD Operations Playing Back an MDPlaying Back the Entire MD Normal Play Recording length mode To go to another track directly using the number buttonsWhile playing or pausing To change the information shown on the displayPress the number buttons to select the tracks To check the program contentsLoad an MD Repeat to program other tracks you wantPress GROUP/TITLE I or GROUP/TITLE I to select a group Playing Tracks in a Group-Group PlayLoad an MD including groups Enter the characters to search for the track title Press Title SearchPress Repeat repeatedly during or before play MD Repeat ALLTo prohibit MD ejection-MD Lock Press REV.MODE Playing Back a TapePlaying Back a Tape Press Tape 2Listening to External Equipment Turn down the volume level to Volume MINListening to External Equipment Press AUXAbout the track marks Recording on an MDBefore You Start Recording on an MD To avoid erasing important recordingsPress Group REC ON/OFF Setting MD Recording ModesPress LP Recording discs onto an MD Disc-MD Synchronized Recording Press CD REC Mode to select the recording modeWhen recording from a CD-R/RW Press REC Speed to select the recording speed you wantTo record a single track during play or pause Recording Other Sources onto an MDPrepare the source to record from Manual Mark Time Auto Mark Press TR. Mark Select to select track mark entry modeREC MD recording indicator starts flashing On the display To protect your recordings Recording on a TapeBefore You Start Recording on a Tape To keep the best recording and playback sound qualityRecording onto a Tape Press Tape RECRecording Disc onto a Tape Disc-Tape Synchronized Recording Press REV.MODE to select a reverse modeWhen recording a disc or an MD To record from the desired trackRecording Discs onto an MD and a Tape MD and tape Elapsed Recording indicatorsWhen recording on an MD and a tape at the same time Disc Synchronized RecordingEditing an MD Using MD Groups as a separate itemHow to make up Groups Guidance-MD Group Functions13 14 Introducing Group Editing FunctionsGroup Insert an MD you want to edit into the MD loading slot When Cannot FORM! appears on the display in stepForming a Group-FORM GR During playbackPress UP ¢ or Down 4 to select the track When Cannot ENTRY! appears on the display in stepAdding a Track to a Group-ENTRY GR Press GROUP/TITLE I or GROUP/TITLE I to select the groupEx. When track 18 is selected Dividing a Group-DIVIDE GRJoining Two Groups-JOIN GR When Cannot Join appears on the display in stepEx. When groups 7 and 8 are selected Moving a Group-MOVE GR Ex. When group 3 is selectedEx. When group 3 is moved to group Insert an MD you want to edit into the MD Ungrouping Tracks-UNGROUPDissolving All Groups-UNGR ALL Loading slotEx. When group 6 is selected Erasing Tracks in a Group-ERASE GRIntroducing Track Editing Functions Dividing a Track-DIVIDE Ex. When adjusting the point byEx. When track 12 is selected Press UP ¢ or Down 4 to select the track you want to divideEx. When tracks 2 and 3 are selected Joining Two Tracks-JOINPress UP ¢ or Down 4 to select the track you want to move Ex. When track 3 is moved to trackMoving a Track-MOVE You can select up to 15 tracks Erasing Tracks-ERASEErasing All Tracks-ALL Erase Appears on the display Track marked with Will be erasedAssigning Titles to an MD Enter the unit into the title entry modePress UP ¢ or Down 4 to change the title entry mode Press Title EditPress Enter to finish the current title entry Press Cancel to exit from the title entry modeEnter characters Press 0 MD eject on the unit to ejectYou can make a correction or change the title To Change the TitleYou can assign titles during play or recording Make sure that the character you want to change is flashingSet the shut-off time Using the TimersUsing Recording Timer Set the start timeSelect the device to record onto To turn off the Recording Timer after its setting is doneTo turn on the Recording Timer again MD REC Tape RECSelect the source to play back Using Daily TimerHow Daily Timer actually works Adjust the volume level Select the fade settingHow Sleep Timer actually works Using Sleep TimerTimer Priority Press Sleep repeatedlyIntroducing the Choice Menus Initial Setting Using Choice MenuConfiguration of the choice menus Operation buttonsPress Choice Operating ProcedurePress Enter to finish the setting Press cursor 3/2 repeatedly to display the Picture menuPicture setting menu-PICTURE Language selection menu-LANGUAGEOther setting menu-OTHERS Dynamic Range CompressionRemember your password or make a note of it Restricting the Access Level-Parental LockSetting Parental Lock Releasing Parental Lock temporarily Changing the Parental Lock settingWhen you enter wrong password three times To return to Others menuCountry/Area codes list for Parental Lock Operating Other Manufacturers’ TV Changing the Preset Signal CodesSet the AUDIO-TV switch to TV Press and hold TV Release TV Press TV to operate your TVAV Compu Link connection Using AV Compu Link Control SystemConnection diagram Available operationsGlossary General Notes MaintenanceCleaning the unit Handling discsMD Disc Types Utoc User Table Of ContentsAdditional Information Atrac Adaptive TRansform Acoustic Coding/ATRAC31st Generation Language Code ListScms Serial Copy Management System MD limitationsDisc/MD Messages Output Signals through the DVD Optical Digital OUT TerminalCD with DTS Digital Surround MP3 disc Output Signals For DiscFor MD X1 onlyTroubleshooting SymptomCassette deck Section Supplied accessoriesTuner Section GeneralEN, CS Victor Company of JAPAN, Limited 1203AIMMDWJEM