JVC UX-J99DVD manual Listening to FM and AM Broadcasts, Setting the AM Tuner Interval Spacing

Page 16

English

Listening to FM and AM Broadcasts

Setting the AM Tuner Interval Spacing

Some countries AM channel intervals are set to 9 kHz apart, and some countries use 10 kHz apart.

When shipped, the built-in AM tuner is set to 9 kHz spacing. You can change the channel interval to 9 kHz or 10 kHz spacing.

•The last selected source must be “AM” in order to perform the following operation.

Be sure that the unit is turned off (on standby), but is plugged into a wall outlet.

On the unit ONLY:

1 Select the AM channel intervals.

•To set the AM tuner to the 10 kHz spacing, press (standby/on) while holding ¢ UP.

¢UP+

•To set the AM tuner to the 9 kHz spacing, press (standby/on) while holding 4 DOWN.

4DOWN +

2 Press .

The unit tunes in to 530 kHz (or 531 kHz).

When you change the AM channel interval spacing

The preset stations you have set (both FM and AM) will be erased. In this case, preset stations again. See “Presetting Stations” on page 14.

2 Press and hold UP ¢ or DOWN 4 for more than 1 second.

4DOWN ¢UP

(On the remote control)

(On the unit)

•UP ¢: Increases the frequencies.

•DOWN 4: Decreases the frequencies.

The unit starts searching for stations and stops when a station of sufficient signal strength is tuned in.

•If an FM program is broadcast in stereo, the STEREO indicator lights up on the display (only when the reception is good).

To stop during searching, press UP ¢ or DOWN 4.

When you press UP ¢ or DOWN 4 repeatedly

The frequency changes step by step.

To change the FM reception mode

When an FM stereo broadcast is noisy or hard to receive, you can change the FM reception mode to improve the reception.

On the remote control ONLY:

Press PLAY/FM MODE.

The MONO indicator lights up on the display.

To restore the stereo effect, press PLAY/FM MODE again so that the MONO indicator goes off. In stereo mode, you can hear stereo

sound when a stereo program is broadcast.

Tuning in to a Station• The STEREO indicator lights up only when the reception is sufficient.

1 Press FM/AM/AUX (or FM/AM on the unit) to select either “FM” or “AM.”

AUX

FM/AM

(On the remote control)

(On the unit)

The unit automatically turns on and tunes in to the previously received station—either FM or AM.

•Each time you press the button, the band changes as follows:

On the remote control:

FM AM

AUX–DIGITAL* AUX*

*For operating the external equipment, see page 44 and the manuals supplied with it.

On the unit:

FM AM

13

Page 15 Page 17
Image 16
Page 15 Page 17
Contents UX-J99DVD Page Important for Laser Products Introduction PrecautionsAbout This Manual Contents Remote Control Remote ControlLocation of the Buttons and Controls Become familiar with the buttons and controls on your unitFront panel Front PanelDisc trays compartment-5-DVD changer Group indicator Reverse mode indicatorDisplay window on the front panel Display windowConnecting Antennas Getting StartedUnpacking Attach the FM antenna to the FM 75 Ω Coaxial terminalConnecting Speakers To connect an outdoor FM antennaAM antenna To connect an outdoor AM antennaRelease your finger from the clamp Connecting a TVTo remove the speaker grilles Connecting Other Equipment Color system of TV Color system settingTo select the color system To connect analog audio equipmentTurning On the Power and Starting Playback Setting the ClockBasic and Common Operations Adjusting the Volume Level To turn down the volume level temporarilyReinforcing the Bass Sound Press Fade MutingAdjusting the Tone Changing the Scanning ModeChanging the Display Brightness Press Dimmer while the unit is turned onSetting the AM Tuner Interval Spacing Listening to FM and AM BroadcastsPresetting Stations Tuning in to a Preset StationPlaying Back Discs on the 5-DVD Changer Disc InformationPlayable disc types About copy protectionDisc structure Playback Control function PBC-SVCD and VCD onlyPlaying Back All the Discs-Continuous Play Loading DiscsLoad discs into the 5-DVD changer Press GROUP/TITLE I or GROUP/TITLE I during playback Basic Disc OperationsPress ¢ or 4 during playback Using the number buttons Press ¡ orPress ¢ or 4 repeatedly Press DISP/CHARAPlaying Back by Using the Disc Menu When playing a DVDWhen playing a Svcd or VCD Press TOP Menu or MenuPrograming the Track Playing Order Program Play Press the number buttons to select a disc trayProgram other tracks you want Press DVDTo check the programed contents Playing at Random-Random PlayTo exit from Program Play To modify the programRepeating Playback-Repeat Play Prohibiting Disc Ejection-Disc LockPress Repeat To exit from Random PlayAdvanced Disc Operations About the On-screen BarPress on Screen Indication Meanings Available discsOperation through the On-screen Bar Press on Screen twicePress Enter On-screen guide iconsRepeating Playback Press cursor ∞/5 repeatedly to select Repeat Play modeTo repeat a current title, group, chapter, or all tracks Press cursor ∞/5 repeatedly to select A-B To repeat a desired portion-A-B RepeatLocating a desired position-Time Search While playing back a DVDEx. When playing a DVD Audio Locating a desired chapter/trackTo correct a misentry Unit starts playback from the specified timeSelecting the Audio Language Selecting the Subtitle LanguagePress Audio Press Audio repeatedly to select the desired audio languageSelecting a View Angle Selecting Browsable Still Pictures recorded onPress Angle Press Angle repeatedly to select the desired view anglePress Virtual Surround Press Audio repeatedly to select the desired audio channelEx. ST 1 ST 2 L 1 R 1 L 2 R ST 1/STSpecial Picture Playback Press 8 oncePress 8 repeatedly Press Slow 9 ¡ orChanging the VFP Setting Press cursor 3/2 repeatedly to select the VFP modeRepeat steps 2 to 4 to adjust other parameters Press VFPPlaying Back a Bonus Group Select a bonus groupWhile the key number entry indication appears On the display On the TV screenPress DVD 8 or #¥8 DVD on the unit MP3/JPEG Disc PlaybackPress ¢ / 4 repeatedly as many times as required Operations through the MP3/JPEG Control Screens Press cursor ∞/5 repeatedly to select a groupPress DVD 3 or Enter Press Repeat during or before playPlaying Back the Entire MD Normal Play Playing Back an MDBasic MD Operations To go to another track directly using the number buttons While playing or pausingRecording length mode To change the information shown on the displayTo check the program contents Load an MDPress the number buttons to select the tracks Repeat to program other tracks you wantLoad an MD including groups Playing Tracks in a Group-Group PlayPress GROUP/TITLE I or GROUP/TITLE I to select a group Press Title Search Press Repeat repeatedly during or before playEnter the characters to search for the track title MD Repeat ALLTo prohibit MD ejection-MD Lock Playing Back a Tape Playing Back a TapePress REV.MODE Press Tape 2Turn down the volume level to Volume MIN Listening to External EquipmentListening to External Equipment Press AUXRecording on an MD Before You Start Recording on an MDAbout the track marks To avoid erasing important recordingsPress LP Setting MD Recording ModesPress Group REC ON/OFF Press CD REC Mode to select the recording mode When recording from a CD-R/RWRecording discs onto an MD Disc-MD Synchronized Recording Press REC Speed to select the recording speed you wantPrepare the source to record from Recording Other Sources onto an MDTo record a single track during play or pause REC MD recording indicator starts flashing On the display Press TR. Mark Select to select track mark entry modeManual Mark Time Auto Mark Recording on a Tape Before You Start Recording on a TapeTo protect your recordings To keep the best recording and playback sound qualityRecording onto a Tape Press Tape RECPress REV.MODE to select a reverse mode When recording a disc or an MDRecording Disc onto a Tape Disc-Tape Synchronized Recording To record from the desired trackMD and tape Elapsed Recording indicators When recording on an MD and a tape at the same timeRecording Discs onto an MD and a Tape Disc Synchronized RecordingUsing MD Groups as a separate item How to make up GroupsEditing an MD Guidance-MD Group FunctionsGroup Introducing Group Editing Functions13 14 When Cannot FORM! appears on the display in step Forming a Group-FORM GRInsert an MD you want to edit into the MD loading slot During playbackWhen Cannot ENTRY! appears on the display in step Adding a Track to a Group-ENTRY GRPress UP ¢ or Down 4 to select the track Press GROUP/TITLE I or GROUP/TITLE I to select the groupEx. When track 18 is selected Dividing a Group-DIVIDE GREx. When groups 7 and 8 are selected When Cannot Join appears on the display in stepJoining Two Groups-JOIN GR Ex. When group 3 is moved to group Ex. When group 3 is selectedMoving a Group-MOVE GR Ungrouping Tracks-UNGROUP Dissolving All Groups-UNGR ALLInsert an MD you want to edit into the MD Loading slotEx. When group 6 is selected Erasing Tracks in a Group-ERASE GRIntroducing Track Editing Functions Ex. When adjusting the point by Ex. When track 12 is selectedDividing a Track-DIVIDE Press UP ¢ or Down 4 to select the track you want to divideEx. When tracks 2 and 3 are selected Joining Two Tracks-JOINMoving a Track-MOVE Ex. When track 3 is moved to trackPress UP ¢ or Down 4 to select the track you want to move Erasing Tracks-ERASE Erasing All Tracks-ALL EraseYou can select up to 15 tracks Appears on the display Track marked with Will be erasedEnter the unit into the title entry mode Press UP ¢ or Down 4 to change the title entry modeAssigning Titles to an MD Press Title EditPress Cancel to exit from the title entry mode Enter charactersPress Enter to finish the current title entry Press 0 MD eject on the unit to ejectTo Change the Title You can assign titles during play or recordingYou can make a correction or change the title Make sure that the character you want to change is flashingUsing the Timers Using Recording TimerSet the shut-off time Set the start timeTo turn off the Recording Timer after its setting is done To turn on the Recording Timer againSelect the device to record onto MD REC Tape RECHow Daily Timer actually works Using Daily TimerSelect the source to play back Adjust the volume level Select the fade settingUsing Sleep Timer Timer PriorityHow Sleep Timer actually works Press Sleep repeatedlyInitial Setting Using Choice Menu Configuration of the choice menusIntroducing the Choice Menus Operation buttonsOperating Procedure Press Enter to finish the settingPress Choice Press cursor 3/2 repeatedly to display the Picture menuPicture setting menu-PICTURE Language selection menu-LANGUAGEOther setting menu-OTHERS Dynamic Range CompressionSetting Parental Lock Restricting the Access Level-Parental LockRemember your password or make a note of it Changing the Parental Lock setting When you enter wrong password three timesReleasing Parental Lock temporarily To return to Others menuCountry/Area codes list for Parental Lock Changing the Preset Signal Codes Set the AUDIO-TV switch to TV Press and hold TVOperating Other Manufacturers’ TV Release TV Press TV to operate your TVUsing AV Compu Link Control System Connection diagramAV Compu Link connection Available operationsGlossary Maintenance Cleaning the unitGeneral Notes Handling discsUtoc User Table Of Contents Additional InformationMD Disc Types Atrac Adaptive TRansform Acoustic Coding/ATRAC3Language Code List Scms Serial Copy Management System1st Generation MD limitationsOutput Signals through the DVD Optical Digital OUT Terminal CD with DTS Digital Surround MP3 disc Output SignalsDisc/MD Messages For DiscFor MD X1 onlyTroubleshooting SymptomSupplied accessories Tuner SectionCassette deck Section GeneralEN, CS Victor Company of JAPAN, Limited 1203AIMMDWJEM
Top Page Image Contents