NordicTrack NTL13007.0 user manual Troubleshooting, Problem The power turns off during use

Page 29

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 14). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 14. IMPORTANT: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch pro- trudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch to the reset position.

PROBLEM: The power turns off during use

c

Tripped

Reset

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch to the reset position.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key into the console.

d. If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE INFORMATION MODE on page 25 to turn off the demo mode.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Next, carefully lower the Uprights (85). Remove the two indicated Belly Pan Screws

(32). Note: A Phillips screwdriver with a shaft at least 8 in. (20 cm) long is needed.

a

 

85

32

29

Image 29
Contents Please do not Contact QUESTIONS?Call TOLL-FREE On the WEBTable of Contents Important Precautions Page Power Lines Service Before YOU Begin Leg Bolts AssemblyMake sure that the power cord is unplugged As shown. Firmly tighten the Extension Leg Bolts Pull on the sleeve to make sure that it is locked into place Start all four Console Bolts and then tighten Them Not shown. Make sure that no wires are PinchedPage Wire Receiver 105 Cylinder HOW to Connect AN External Source Using a Catv Cable HOW to Connect a 75 OHM Catv CablePRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Press the Start button to start the program HOW to USE a Preset ProgramHOW to USE a Pulse Program See on HOW to Create a Custom Program HOW to USE a Custom Program Measure your heart rate if desired HOW to USE AN Ifit CardPress the Volume buttons to adjust the volume HOW to Operate the Personal TelevisionHOW to USE the Stereo Sound System Press the Channel buttons to select the desired channelPress the Power button again and add or re- move channels Information ModeOptional Chest Pulse Sensor HOW to Adjust the Cushioning SystemHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked onProblem Television reception is poor Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Qty Description R1107AQty NTL13007 Exploded Drawing B-Model No. NTL13007.0 Exploded Drawing C-Model No. NTL13007.0 Exploded Drawing D-Model No. NTL13007.0 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty