NordicTrack NTL13007.0 user manual Pull on the sleeve to make sure that it is locked into place

Page 9

5.Identify the Latch Assembly (76). Remove the tie from the end of the tube. Make sure that the sleeve has been slid over the indicated hole and that the Latch Knob (50) is locked into the hole.

Pull on the sleeve to make sure that it is locked into place.

6.Raise the Frame (55) to the position shown.

Have a second person hold the Frame until this step is completed.

Orient the Latch Assembly (76) so that the large barrel and the Latch Knob (50) are in the posi- tions shown.

Attach the Latch Assembly (76) to the Uprights

(85)with a 3/8" x 2" Bolt (109) and a 3/8" Nut

Attach the upper end of the Latch Assembly (76) to the bracket on the Frame (55) with a 3/8" x 2" Bolt (109) and a 3/8" Nut (20). Note: It may be necessary to move the Frame back and forth to align the Latch Assembly with the bracket.

Lower the Frame (55) (see HOW TO LOWER THE TREADMILL FOR USE on page 28).

7.Identify the Left Base Cover (88), which has cutouts in the locations shown. Slide the Left Base Cover onto the left Upright (85). Then, slide the Right Base Cover (86) onto the right Upright.

Identify the Left Upright Sleeve (77) and the Right Upright Sleeve (9). Slide the Upright Sleeves onto the Uprights (85) as shown.

5

 

 

 

 

 

50

 

Tube

 

Hole

 

 

Sleeve

 

 

 

 

76

6

 

 

 

 

 

55

 

 

20

109

 

 

 

 

 

 

76

 

 

50

 

 

 

 

Large

 

 

 

Barrel

 

 

 

85

 

 

20

 

 

 

109

 

7

 

85

 

 

 

 

 

 

77

 

Cutouts

 

88

9

 

 

86

 

9

 

 

 

Image 9
Contents Please do not Contact QUESTIONS?Call TOLL-FREE On the WEBTable of Contents Important Precautions Page Power Lines Service Before YOU Begin Assembly Make sure that the power cord is unpluggedLeg Bolts As shown. Firmly tighten the Extension Leg Bolts Pull on the sleeve to make sure that it is locked into place Start all four Console Bolts and then tighten Them Not shown. Make sure that no wires are PinchedPage Wire Receiver 105 Cylinder HOW to Connect AN External Source Using a Catv Cable HOW to Connect a 75 OHM Catv CableOperation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Press the Start button to start the program HOW to USE a Preset ProgramHOW to USE a Pulse Program See on HOW to Create a Custom Program HOW to USE a Custom Program Measure your heart rate if desired HOW to USE AN Ifit CardPress the Volume buttons to adjust the volume HOW to Operate the Personal TelevisionHOW to USE the Stereo Sound System Press the Channel buttons to select the desired channelPress the Power button again and add or re- move channels Information ModeOptional Chest Pulse Sensor HOW to Adjust the Cushioning SystemHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked onProblem Television reception is poor Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Qty Description R1107AQty NTL13007 Exploded Drawing B-Model No. NTL13007.0 Exploded Drawing C-Model No. NTL13007.0 Exploded Drawing D-Model No. NTL13007.0 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT