Precor M 9.1, M 9.2s Checking the Alignment of the Running Belt, See Aligning the Running Belt

Page 15

CAUTION: Do not remove the 3-prong plug or otherwise bypass it with an adapter in order to use a non-grounded outlet.

Note: After extensive use, vibrations from the treadmill may cause the clamp to loosen. You may need to periodically inspect the screws and, if necessary, tighten the handrail clamp screws using the hex key (G) provided.

e.Proceed to the other side of the treadmill and follow steps a through d to complete the installation of the lower handrails.

24.Return to the upper handrail clamp, look underneath the clamp to be sure that the handrail ends meet in the middle of the clamp, readjust the handrails if necessary, and tighten the screws securely using the hex key (F) provided.

25.If you need to move the treadmill, ask for additional assistance. Check to be sure the treadmill is turned OFF and the power cord is unplugged from the power outlet. Roll the treadmill on its front wheels to the new location by lifting the rear end of the unit.

26.Plug the treadmill into a standard 120v household outlet. Make sure that no other appliances use the same circuit as the treadmill.

27.Continue on to Checking the Alignment of the Running Belt on the following page to complete the installation of the treadmill.

CAUTION: Do not walk on the running belt during this procedure.

CAUTION: If you hear or notice any chafing or the running belt appears to be getting damaged, stop the running belt immediately by pressing the STOP key. Contact a Precor Service Representative.

Checking the Alignment of the Running Belt

The belt is aligned at the factory before shipment. However, during shipment or by using the treadmill on an uneven surface, the belt might move off center. Proper belt alignment is important because it allows the belt to remain centered and assures smooth operation. Follow these steps to check the alignment:

1.On the electronic console, move the magnetic safety key to the ACTIVATE position. Locate the ON/OFF switch at the front of the treadmill and turn ON the treadmill.

2.Stand beside the treadmill and answer the standard start-up questions as instructed below:

a.At the “ENTER WEIGHT” prompt, specify a weight and press the SCAN/ENTER key.

b.At the “SELECT COURSE” prompt, use the arrow keys to select “MANL” (Manual) mode and press SCAN/ENTER.

3.Continue standing next to the treadmill and bring the running belt up to a speed of 2 miles per hour by pressing the SPEED key.

4.Walk to the back of the treadmill and observe the belt as it moves (watch for a couple of minutes).

 

If the running belt,…

Then,...

 

 

 

 

tracks within the green portion

the belt is functioning correctly

 

of the label

and no adjustment is necessary.

 

 

 

 

runs or drifts into the red portion

you need to adjust the belt;

 

of the label

see Aligning the Running Belt in

 

 

Chapter 6.

Important: If you notice that the belt needs alignment, make the adjustments at once. Failure to do so might cause the belt to tear or fray which is not covered by the Precor limited warranty.

5.Press STOP or SPEED until the running belt stops.

If the belt is functioning correctly, the treadmill is ready to use.

page 9

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Precision Electronic Treadmill Important Safety Instructions Precor Smart Weights-Safety Guidelines Personal SafetyFCC Communications Commission, part Information Regarding International UseGrounding Instructions Diagram aTable of Contents Before You Begin Unpacking the M9.1 or M9.2s TreadmillOptional Equipment BCD Setting Up the M9.1 or M9.2s Treadmill Installation RequirementsAssembly Instructions Column Install liftHandrail PlugBoard Flanged nuts a Base plate Motor chassis Cross beamHandrail clamp not shown Attach electronic console toHandrail clamp Overtighten Attach trim strip toLift column Handrails See Aligning the Running Belt Checking the Alignment of the Running BeltUsing the M9.1 or M9.2s Treadmill Locating the on and OFF SwitchUsing the Magnetic Safety Key Displays on the Electronic Console Understanding the Electronic ConsoleScan Keys on the Electronic ConsoleSelecting the Time or Distance Prompt on the M9.2s Changing the Display to U.S. Standard or MetricTreadmill Working Out on Your TreadmillQuick Steps to Working Out Cooling Down After a Workout Pausing Your WorkoutChanging Incline on the M9.1 Retrieving the Previous Workout ProgramChanging the Interval Course Profile Using the Manual Course ModeUsing the M9.2s Preprogrammed Courses Page Erector Spinae Gluteals Hip Flexors Getting the Most Out of Your WorkoutHow Hard Should I Exercise? Heart Rate Training ZoneHow Often Should I Exercise? How Long Should I Exercise?Cleaning the Equipment Maintaining Your TreadmillAligning the Running Belt Adjusting the Tension of the Belt Running beltSide platform Running bed Rear roller M9.1 or M9.2s Long Term Storage Power Cord MaintenanceObtaining Service Servicing the TreadmillSpecifications Electronic SpecificationsElectronic Displays

M 9.2s, M 9.1 specifications

The Precor M 9.1 and M 9.2s are sophisticated fitness machines designed to elevate workout experiences for users seeking effective cardiovascular training. Both models showcase Precor's commitment to quality, innovation, and performance, making them ideal choices for both home gyms and commercial fitness centers.

One of the standout features of the Precor M 9.1 is its ergonomic design that promotes comfort during use. The unit is equipped with a broad, cushioned footbed that reduces the impact on joints while still providing a robust workout. This design not only enhances user comfort but also encourages longer workout sessions, allowing fitness enthusiasts to push their limits without the risk of discomfort or injury.

The M 9.2s model takes comfort a step further, featuring an upgraded display console that offers intuitive controls and personalized workout programs. Users can easily navigate through various exercise modalities, including steady-state training, interval workouts, and heart-rate-based sessions. This versatility enables individuals to tailor their workouts to suit their fitness levels or specific goals.

Both models utilize Precor's renowned resistance technology, providing a smooth and consistent experience during workouts. The resistance levels can be easily adjusted, catering to users of all fitness levels, from beginners to advanced athletes. This adaptability is particularly beneficial in a shared gym environment where multiple users have different fitness backgrounds and goals.

An essential characteristic of the M 9.1 and M 9.2s is the integration of advanced monitoring systems. These consoles feature in-depth tracking capabilities, allowing users to monitor metrics such as heart rate, calories burned, and workout duration. Such data not only keeps users motivated but also empowers them to assess their progress and make informed adjustments to their fitness regimens.

Additionally, both models are designed with durability in mind. Constructed from high-quality materials, they are built to withstand the rigors of daily use, making them perfect for high-traffic gym environments. This durability is complemented by a low-maintenance design, with parts that are easy to access and replace if necessary.

In summary, the Precor M 9.1 and M 9.2s are impressive fitness machines that combine comfort, durability, and advanced technology. With a focus on user experience, personalized workouts, and performance tracking, they are excellent choices for anyone looking to enhance their cardio routines, whether at home or in a commercial setting. As fitness continues to evolve, these models remain at the forefront of innovative exercise solutions.
Top Page Image Contents