Precor C966 Setting Up the Treadmill, Installation Requirements, Additional Tools Needed

Page 10

C O M M E R C I A L P R O D U C T S D I V I S I O N

Setting Up the Treadmill

You do not need any special knowledge or experience to set up the treadmill. However, because of its size and weight, you will need to obtain assistance.

INSTALLATION REQUIREMENTS

Follow these installation requirements when installing the treadmill. If you do not install the treadmill according to the following guidelines, you could void the Precor limited warranty.

•Set up the treadmill on a solid, flat surface. Unpack and assemble the treadmill close to where you plan to use it. Make sure that the flat surface under the unit is smooth and level.A level unit is required for the user’s safety and proper operation.

•Provide ample space around the unit. Open space around the unit makes for a safer mount and dismount.

•Fill out and mail the limited warranty card. The serial number can be found on the shipping container or on the label near the power receptacle. Write the serial number onto the Precor limited warranty card found on the back cover of this manual and in the Obtaining Service section on page 7.

•Use the appropriate voltage, dedicated circuit, and grounding as speci- fied on the treadmill. The treadmill is available in both 120-volt and 240-volt models. Refer to the treadmill’s identification label to determine the voltage that your treadmill requires. Both the 120-volt and 240-volt models require a dedicated circuit. A 20 amp circuit is recommended.

CAUTION: Do not use a non-grounded outlet or transformer. Do not remove or otherwise bypass the plug with an adapter. Electrical damage can occur and void the Precor limited warranty if the treadmill is connected to an improper power source. Refer to Grounding Instructions on page 3.

ADDITIONAL TOOLS NEEDED

Obtain the following tools before assembling the treadmill.

❑

Wire cutter

❑

Medium weight string

❑

Bubble level

❑

¹⁄₂-inch box end wrench

❑SAE standard socket set with a ratchet or 8-inch crescent wrench

ASSEMBLY INSTRUCTIONS

Take the following steps to assemble the treadmill.

CAUTION:To avoid injury and ensure your safety, get assistance before moving the treadmill off the pallet. Do not drop the unit.

1.Think about the site and location. Have your assistants help place the shipping carton close to the location where you plan to use the treadmill. Break down the side walls of the shipping carton so that they lie flat. Remove the loose contents.

2.Make sure that the power switch is OFF. Check the ON/OFF power switch on the front of the treadmill. Place the switch in the O (OFF) position. Make sure that the treadmill is not plugged into a power source.

page 10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents M M E R C I a L P R O D U C T S D I V I S I O N Important Safety Instructions Safety Approval Grounding InstructionsTable of Contents Courses MaintenanceExercising on the Treadmill Back coverRadio Frequency Interference RFI European ApplicationsObtaining Service About this ManualStandard Equipment Unpacking the TreadmillOther Equipment Hardware KIT Assembly Instructions Setting Up the TreadmillInstallation Requirements Additional Tools NeededDiagram Remove Attach Connect M M E R C I a L O D U C T S V I S I O N Diagram 13 Handrail alignment and installation Diagram M M E R C I a L O D U C T S V I S I O N Power cord to Checking the Alignment of the Running Belt Turning the Unit on and OFFIf the running belt Then Changing the Club Settings Club InformationKeypad key functions within the Club Custom Mode To access the Club settings, the following must occurSpeed , Speed , Speed , Reset, Speed , Speed , Speed Selecting the LanguageSetting a Cool Down Time Limit Setting a Workout Time LimitSetting a Pause Time Limit Determining the Club Speed LimitChanging the Custom Courses Speed or Incline or Enter Stop or ResetRemoving or Providing a Fitness Test Press Enter to confirm your selectionSpeed , Speed Or, you can opt to use the number keys 6 Using Csafe Standard EquipmentReset User ID Entry Program KeysFeatures on the Display Console C966 DisplayUpper Display TOP Display WindowsCenter Display M M E R C I a L P R O D U C T S D I V I S I O N Keys on the Display Console Keypad TipsM M E R C I a L P R O D U C T S D I V I S I O N If QuickStart is pressed after an Age is entered, then Quickstart Default ValuesPrompts DefaultValue Chest strap. If no Age entry occurs, the SmartRate displayPress QuickStart at Following occurs Exercising on the Treadmill Using the Security ClipPAUSE, Cool DOWN, Summary and Exit Features A course You press This is what happensCool down You press This is what happens Pause mode You press This is what happensSpeed At theWorkout Summary banner You press This is what happensFor your Heart Rate to appear on the display, you need to Quick Steps to Working OUTWorkout Tips Grips on the handrailCooling Down After a Workout Using the Smartrate Feature Heart Rate FeatureCourses Weight RateManual Mode and the Quickstart KEY Track CourseInterval Course 5K CoursePreprogrammed Courses To use the interval course, take the following stepsFitness Test Custom CoursesFitness Test Guidelines Fitness Test ends if any one of the following occurs Random CourseHeart Rate Course You press the Stop keyWeight Loss Course GOAL-BASED Courses Inspection MaintenanceCleaning the Equipment Perform a daily inspection of the treadmillAligning the Running Belt AlignStoring the Polar Chest Strap Servicing the TreadmillLong Term Storage Exploded Views View Exploded Views Exploded Views Exploded Views Thank You and Welcome to Precor Please indicate the type and number of products purchased Date of PurchaseProduct Serial Numbers How many members do you have?Conditions and Restrictions Limited WarrantyWarranty Periods and Coverage Complete this portion and keep for your recordsProduct Specifications Electronic Specifications
Top Page Image Contents