Precor C966 owner manual Removing or Providing a Fitness Test, Changing the Custom Courses

Page 24

C O M M E R C I A L P R O D U C T S D I V I S I O N

REMOVING OR PROVIDING A FITNESS TEST

The Fitness Test is “enabled” at the factory (course number 16), so if you wish to remove the option from the user’s choice of programs on the C966, you need to “disable” the Fitness Test.

Important: If you “disable” the Fitness Test, it is no longer available to the user. Custom Course 2 takes its place as course number 16.

After displaying a cool down time limit and entering your selection, the Fitness Test prompt appears on the display. Use the ▼▲ keys to select “enabled” or “disabled”.

Press Enter to confirm your selection.

CHANGING THE CUSTOM COURSES

Two custom course programs (Course 1 and Course 2) exist in the C966 treadmill. After you modify Course 1 (or opt to bypass it), Course 2 appears on the display. The keys on the console keypad have a different function than explained in the box on page 21. In the Custom Course programs, the keys function as follows:

Custom Course Program Keys

Speed ▼ or ▲

Incline ▲ or ▼

Enter

Stop or Reset

moves the blinking LED from column to column.

affects the incline of the selected column.

accepts any changes and stores the course in memory.

exits the course (leaving it unchanged) and resets the display to the Precor banner.

If you decide to select a custom course, you have the ability to create a new, or “draw over” an existing, course profile.The entire course appears on the display. A blinking LED appears at the top of the far left column and indicates the starting position. Any incline changes that you make occur only in that column. The treadmill’s speed is determined by the user.

Begin modifying the course profile using any Incline ▲ or ▼ key. The available incline range is a negative 3% to a positive 15%. To move onto the next column, press any Speed ▼ or ▲ key. (Refer to the chart above.)

When you have finished making changes, press Enter to save the course profile. The display moves to the next Custom Course (#2) or returns to the Precor banner (depending on which Custom Course you were modifying).

Note: To exit the custom course mode without saving any of the changes, press Stop or Reset.The custom course that existed prior to your changes is reinstated and the display returns to the Precor banner.

VIEWING THE ODOMETER, HOURS OF USE, SOFTWARE VERSION, ERROR LOG AND SERIAL NUMBER

The treadmill stores the cumulative miles or kilometers, the number of hours that the unit has been in use, the software version and software type (which is valuable when calling customer support), and an error log (useful when troubleshooting).

page 24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents M M E R C I a L P R O D U C T S D I V I S I O N Important Safety Instructions Safety Approval Grounding InstructionsTable of Contents Maintenance Exercising on the TreadmillCourses Back coverRadio Frequency Interference RFI European ApplicationsObtaining Service About this ManualUnpacking the Treadmill Standard EquipmentOther Equipment Hardware KIT Setting Up the Treadmill Installation RequirementsAssembly Instructions Additional Tools NeededDiagram Remove Attach Connect M M E R C I a L O D U C T S V I S I O N Diagram 13 Handrail alignment and installation Diagram M M E R C I a L O D U C T S V I S I O N Power cord to Turning the Unit on and OFF Checking the Alignment of the Running BeltIf the running belt Then Changing the Club Settings Club InformationTo access the Club settings, the following must occur Speed , Speed , Speed , Reset, Speed , Speed , SpeedKeypad key functions within the Club Custom Mode Selecting the LanguageSetting a Workout Time Limit Setting a Pause Time LimitSetting a Cool Down Time Limit Determining the Club Speed LimitSpeed or Incline or Enter Stop or Reset Removing or Providing a Fitness TestChanging the Custom Courses Press Enter to confirm your selectionUsing Csafe Standard Equipment ResetSpeed , Speed Or, you can opt to use the number keys 6 User ID Entry Program KeysFeatures on the Display Console C966 DisplayTOP Display Windows Upper DisplayCenter Display M M E R C I a L P R O D U C T S D I V I S I O N Keys on the Display Console Keypad TipsM M E R C I a L P R O D U C T S D I V I S I O N Quickstart Default Values Prompts DefaultValueIf QuickStart is pressed after an Age is entered, then Chest strap. If no Age entry occurs, the SmartRate displayPress QuickStart at Following occurs Using the Security Clip PAUSE, Cool DOWN, Summary and Exit FeaturesExercising on the Treadmill A course You press This is what happensPause mode You press This is what happens SpeedCool down You press This is what happens At theWorkout Summary banner You press This is what happensQuick Steps to Working OUT Workout TipsFor your Heart Rate to appear on the display, you need to Grips on the handrailCooling Down After a Workout Heart Rate Feature Using the Smartrate FeatureCourses Weight RateManual Mode and the Quickstart KEY Track Course5K Course Preprogrammed CoursesInterval Course To use the interval course, take the following stepsCustom Courses Fitness TestFitness Test Guidelines Random Course Heart Rate CourseFitness Test ends if any one of the following occurs You press the Stop keyWeight Loss Course GOAL-BASED Courses Maintenance Cleaning the EquipmentInspection Perform a daily inspection of the treadmillAligning the Running Belt AlignServicing the Treadmill Storing the Polar Chest StrapLong Term Storage Exploded Views View Exploded Views Exploded Views Exploded Views Thank You and Welcome to Precor Date of Purchase Product Serial NumbersPlease indicate the type and number of products purchased How many members do you have?Limited Warranty Warranty Periods and CoverageConditions and Restrictions Complete this portion and keep for your recordsProduct Specifications Electronic Specifications
Top Page Image Contents