Precor C966 owner manual Remove

Page 12

C O M M E R C I A L P R O D U C T S D I V I S I O N

Diagram 5

Remove the

 

shipping

 

fasteners from

 

the left side front

 

panel.

Shipping fasteners found on left and right sides of the front panel.

Left side mounting bracket

5.Attach the left side upright support. Diagram 5. Take the following steps.

a.Remove the shipping fasteners from the front panel. With the supplied hex key and a 1/2-inch box end wrench, loosen and remove the two bolts and nuts on the left side of the front panel.These fasteners hold the front panel in place during shipping. (The front panel will drop slightly when you remove the fasteners.) Discard the nuts, but keep the bolts.

Diagram 6

Secure the left

1

2

 

upright support.

 

Screws (D),

 

 

 

washers (E),

 

 

 

and barrel

 

 

 

spacers (F)

 

 

 

Left upright

 

 

 

support

 

 

 

Shipping

 

 

 

fasteners with

 

 

 

washers (B)

 

3

b.Attach the left upright support by placing it inside the base mount and align- ing the mounting holes. Obtain two long sockethead screws (D), washers (E) and barrel spacers (F) from the Hardware kit. Place a washer and barrel sleeve on each screw and insert the fasteners through the side of the upright support and into the base mounts. Use the 1/4-inch hex key to secure the screws, but leave room for adjustments. See Diagram 6, #1 and #2.

c.Remove two stainless steel washers (B) from the Hardware kit and place a washer on each of the two shipping fasteners. Reinsert the two shipping fasteners removed in step 5a, and finger tighten. See Diagram 6, #3.

page 12

Image 12
Contents M M E R C I a L P R O D U C T S D I V I S I O N Important Safety Instructions Safety Approval Grounding InstructionsTable of Contents Maintenance Exercising on the TreadmillCourses Back coverRadio Frequency Interference RFI European ApplicationsObtaining Service About this ManualUnpacking the Treadmill Standard EquipmentOther Equipment Hardware KIT Setting Up the Treadmill Installation RequirementsAssembly Instructions Additional Tools NeededDiagram Remove Attach Connect M M E R C I a L O D U C T S V I S I O N Diagram 13 Handrail alignment and installation Diagram M M E R C I a L O D U C T S V I S I O N Power cord to Turning the Unit on and OFF Checking the Alignment of the Running BeltIf the running belt Then Changing the Club Settings Club InformationTo access the Club settings, the following must occur Speed , Speed , Speed , Reset, Speed , Speed , SpeedKeypad key functions within the Club Custom Mode Selecting the LanguageSetting a Workout Time Limit Setting a Pause Time LimitSetting a Cool Down Time Limit Determining the Club Speed LimitSpeed or Incline or Enter Stop or Reset Removing or Providing a Fitness TestChanging the Custom Courses Press Enter to confirm your selectionUsing Csafe Standard Equipment ResetSpeed , Speed Or, you can opt to use the number keys 6 User ID Entry Program KeysFeatures on the Display Console C966 DisplayTOP Display Windows Upper DisplayCenter Display M M E R C I a L P R O D U C T S D I V I S I O N Keys on the Display Console Keypad TipsM M E R C I a L P R O D U C T S D I V I S I O N Quickstart Default Values Prompts DefaultValueIf QuickStart is pressed after an Age is entered, then Chest strap. If no Age entry occurs, the SmartRate displayPress QuickStart at Following occurs Using the Security Clip PAUSE, Cool DOWN, Summary and Exit FeaturesExercising on the Treadmill A course You press This is what happensPause mode You press This is what happens SpeedCool down You press This is what happens At theWorkout Summary banner You press This is what happensQuick Steps to Working OUT Workout TipsFor your Heart Rate to appear on the display, you need to Grips on the handrailCooling Down After a Workout Heart Rate Feature Using the Smartrate FeatureCourses Weight RateManual Mode and the Quickstart KEY Track Course5K Course Preprogrammed CoursesInterval Course To use the interval course, take the following stepsCustom Courses Fitness TestFitness Test Guidelines Random Course Heart Rate CourseFitness Test ends if any one of the following occurs You press the Stop keyWeight Loss Course GOAL-BASED Courses Maintenance Cleaning the EquipmentInspection Perform a daily inspection of the treadmillAligning the Running Belt AlignServicing the Treadmill Storing the Polar Chest StrapLong Term Storage Exploded Views View Exploded Views Exploded Views Exploded Views Thank You and Welcome to Precor Date of Purchase Product Serial NumbersPlease indicate the type and number of products purchased How many members do you have?Limited Warranty Warranty Periods and CoverageConditions and Restrictions Complete this portion and keep for your recordsProduct Specifications Electronic Specifications