ProForm PFB48030 user manual Locate the Lat Cable 81. Route the Cable up

Page 16

35. Locate the Lat Cable (81). Route the Cable up

35

 

81

through the Rear Top Frame (39) and over a

 

 

 

 

 

 

90mm Pulley (90). Attach the Pulley inside the

 

 

39

Rear Top Frame with an M10 x 78mm Bolt (110),

 

 

 

 

90

two M10 Washers (99), two 17mm Spacers (86),

 

 

 

 

 

and an M10 Nylon Locknut (97).

97

 

 

 

 

 

 

99 86

 

 

 

 

86

 

 

 

99

 

 

 

110

36. Route the Lat Cable (81) over a 90mm Pulley

36

 

 

(90) and down through the Rear Top Frame (39).

 

 

97

 

 

Attach the Pulley inside the Rear Top Frame with

 

 

86

81

 

an M10 x 78mm Bolt (110), two M10 Washers

90

 

 

(99), two 17mm Spacers (86), and an M10 Nylon

99

 

39

Locknut (97).

 

 

 

 

 

 

 

86

 

 

 

99

 

 

 

110

37. Wrap the Lat Cable (81) under a 90mm Pulley

37

 

 

(90). Attach the Pulley and a Small Cable Trap

 

 

 

 

 

(125) to the indicated hole in the two Pulley

 

 

81

Plates (72) with an M10 x 45mm Bolt (112) and

97

 

 

 

an M10 Nylon Locknut (97). Make sure the

 

125

 

 

Cable Trap is turned to hold the Cable in the

72

 

 

groove of the Pulley.

 

112

 

 

 

 

 

90

 

 

 

72

38. Wrap the Lat Cable (81) over a 90mm Pulley

38

 

39

(90). Attach the Pulley inside the Rear Top Frame

 

 

 

(39) with an M10 x 78mm Bolt (110) and an M10

 

 

 

Nylon Locknut (97).

 

 

90

 

 

 

 

 

97

110

 

 

 

 

 

 

81

39. Attach the Lat Cable (81) to the M10 x 19mm Hex

39

 

 

Head Bolt (132) in the Weight Carriage (71) with

 

 

 

 

81

an M10 Nylon Locknut (97). Do not overtighten

 

 

the Locknut; the Cable must be able to pivot.

 

 

 

 

 

 

71

 

97

 

 

 

132

 

 

16

 

 

Image 16
Contents Model No. PFB48030 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Right Side Before YOU BeginLeft Side Make Things Easier for Yourself AssemblyLocknuts yet Lubricate Flat Head Screw 27 is under a notch in the Backrest Bracket Tighten the six M10 Nylon Locknuts 97 used in steps 1Into the Pad Tube. Repeat with the other Do not tighten the Locknuts yet Do not tighten the Locknuts yet Locknuts 97. Do not tighten the Locknuts yet Not tighten the Screw yetNylon Locknut 97. Do not tighten the Locknut Yet Holes in the Rear Upright. Do not tighten Locknuts yet Attach the Left Fly Arm 44 in the same MannerPage Cable Trap is turned to hold the Cable Groove of the Pulley Locate the Lat Cable 81. Route the Cable upLocknut the Cable must be able to pivot 127 Locknut the Cable must be able to pivot easily Adjusting the Backrest AdjustmentsAttaching the Curl Post Adding Weights to the LEG Lever Using the Olympic Weight AdapterAttaching the Accessories Using the Locking BAR Adding Weights to the Barbell or the Weight CarriageMoving the Safety Spotters Cable Diagrams Butterfly CableLat Cable Low CableTroubleshooting Tightening the CablesExercise Guidelines Cooling Down Staying MotivatedExercise Weight Sets Reps DateAerobic Exercise Thursday Aerobic Exercise DateMonday Part Identification CHART-Model No. PFB48030 R1103APage Page Part LIST-Model No. PFB48030 Key Qty DescriptionExploded DRAWING-Model No. PFB48030 Exploded DRAWING-Model No Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT