JVC RX-7000RBK Basic Settings, Recording a Source, Adjusting the Front Speaker Output Balance

SOURCE SELECTOR

English

Basic Settings

Some of the following settings are required after connecting and positioning your speakers in your listening room, while others will make operations easier.

IMPORTANT:

When using the remote control, check to see if its remote control mode selector is set to the correct

AUDIO/

position:TV/VCR

To operate this receiver, set it to “AUDIO/TV/

CATV/DBS

VCR”

Recording a Source

For analog-to-analog recording

You can record any analog source through the receiver to —

•the cassette deck (or MD recorder) connected to the TAPE/MD jacks,

•and the VCR connected to the VCR jacks

— at the same time.

For digital-to-digital recording

You can record the currently selected digital input through the receiver to a digital recording device connected to the DIGITAL OUT terminal.

Notes:

•Analog-to-digital and digital-to-analog recordings are not possible.

•The output volume level, bass boost (see page 12), SEA modes (see page 24), and DSP modes (see page 25) cannot affect the recording.

•The test tone signal (see pages 29 and 30) does not come out through the DIGITAL OUT terminal.

Adjusting the Front Speaker Output

Balance

If the sounds you hear from the front right and left speakers are unequal, you can adjust the speaker output balance.

Changing the Source Name

When you have connected an MD recorder to the TAPE/MD jacks or the DBS tuner to the TV SOUND/DBS jacks on the rear panel, change the source name which will be shown on the display when you select the MD recorder or DBS tuner as the source.

On the front panel ONLY:

1. When changing the source name from “TAPE” to “MD”:

• Turn SOURCE SELECTOR until “TAPE” appears.

When changing the source name from “TV SOUND” to “DBS”:

•Turn SOURCE SELECTOR until “TV SOUND” appears.

2. Press and hold SOURCE NAME	BASS BOOST
(BASS BOOST) until “ASSGN.	SOURCENAME
MD” or “ASSGN. DBS” appears
on the display.

To change the source name to “TAPE” or “TV SOUND,” repeat

the same procedure above — in step 1, select “MD” or “DBS” then press and hold SOURCE NAME (BASS BOOST).

Note:

Without changing the source name, you can still use the connected components. However, there may be some inconvenience.

–“TAPE” or “TV SOUND” will appear on the display when you select the MD recorder or DBS tuner.

–You cannot use the digital input (see page 16) for the MD recorder.

–You cannot use the COMPU LINK remote control system (see page 39) to operate the MD recorder.

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

1. Press BALANCE (/SURROUND)	BALANCE/SURROUND
ADJUST repeatedly until “L/R		ADJUST

BALANCE” appears on the display.

Setting the Subwoofer Information

Register whether or not you have connected a subwoofer.

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

The display changes to show the current setting.

2. Turn MULTI JOG to adjust the	MULTI JOG
balance.

• Turning it clockwise decreases the left

On the front panel ONLY:

1. Press SETTING repeatedly until “SUBWOOFER” appears on the display.

SETTING

channel output.

• Turning it counterclockwise decreases the

right channel output.

The display changes to show the current setting.

MULTI JOG

2.Turn MULTI JOG to register whether you have connected a subwoofer or not.

•As you turn it, the subwoofer setting alternates between “YES” and “NO.”

YES: Select this when a subwoofer is used. SUBWFR lights up on the display (see page 11).

NO: Select this when no subwoofer is used.

13