JVC RX-7000RBK Crossover FRQ Crossover Frequency appears on the display, Turn Multi JOG to select

Page 18

English

Crossover Frequency Setting

Small speakers cannot reproduce the bass sound very well. So, if you have used a small speaker for any of the front, center, or rear channels, this receiver automatically reallocates the bass elements, originally assigned to the channel for which you have connected the small speaker, to another channel (for which you have connected the large speaker).

To use this function properly, you need to set the crossover frequency level according to the size of the small speaker connected.

•If you have selected “LARGE” for all speakers (see page 14), this function is set to “OFF” and can not be adjusted.

On the front panel ONLY:

1. Press SETTING repeatedly until

SETTING

“CROSSOVER FRQ” (Crossover

 

Frequency) appears on the display.

 

The display changes to show the current setting.

2. Turn MULTI JOG to select the

MULTI JOG

crossover frequency level

 

according to the size of the small

 

speaker connected.

 

•As you turn it, the display changes to show the following:

80Hz100Hz120Hz

•Use the following comments as reference when adjusting.

80Hz: Select this when the cone speaker unit built in the speaker is about 12 cm (4 3/4 inches).

100Hz: Select this when the cone speaker unit built in the

speaker is about 10 cm (3 15/16 inches).

120Hz: Select this when the cone speaker unit built in the speaker is about 8 cm (3 3/16 inches).

Note:

Crossover frequency setting is not valid for the DVD MULTI playback mode, 3D-PHONIC mode and HEADPHONE mode.

Low Frequency Effect Attenuator Setting

If the bass sound is distorted while playing back a source using Dolby Digital, DTS Digital Surround, or MPEG Multichannel, follow the procedure below.

On the front panel ONLY:

1. Press SETTING repeatedly until

SETTING

“LFE ATT” (Low Frequency

 

Effect Attenuator) appears on the

 

display.

The display changes to show the current setting.

2. Turn MULTI JOG to select the

MULTI JOG

low frequency effect attenuator

 

level.

 

•As you turn it, the display changes to show the following:

0dB 10dB

0dB: Normally select this.

10dB: Select this when the bass sound is distorted.

Note:

Low frequency effect attenuator setting is not valid for the DVD MULTI

playback mode.

Dynamic Range Compression Setting

You can compress the dynamic range (difference between maximum sound and minimum sound) of the reproduced sound. This is useful when enjoying surround sound at night.

•This function takes effect only when playing back a source using Dolby Digital.

On the front panel ONLY:

1. Press SETTING repeatedly until

SETTING

“D. RANGE COMP.” (Dynamic

 

Range Compression) appears on

 

the display.

 

The display changes to show the current setting.

2. Turn MULTI JOG to select the

MULTI JOG

appropriate item about the

 

compression level.

 

•As you turn it, the display changes to show the following:

OFF MID MAX

OFF: Select this when you want to enjoy surround with its full dynamic range. (No effect applied)

MID: Select this when you want to reduce the dynamic range a little. (Factory setting)

MAX: Select this when you want to apply the compression effect fully. (Useful at night)

Note:

Dynamic Range Compression setting is not valid for the DTS Digital Surround, MPEG Multichannel and DVD MULTI playback mode.

15

Page 17 Page 19
Image 18
Page 17 Page 19
Contents RX-7000RBK Per I’ltalia Achtung -- STANDBY/ON -SchalterEspañol Italiano Table of Contents Remote Control Parts IdentificationFront Panel Connecting the FM and AM MW/LW Antennas Before InstallationChecking the Supplied Accessories Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure AM MW/LW Antenna ConnectionsConnecting the subwoofer speaker Connecting Audio/Video ComponentsConnecting the rear and center speakers About the speaker impedanceCD player Cassette deck or MD recorderVideo component connections DVD player TV and/or DBS tunerDVD player DBS tunerDigital connections Digital input terminalsDigital output terminal Plug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control R6PSUM-3/AA15FBasic Operations Turning the Power On and Off StandbyFrom the remote control Selecting the Source to PlayEtc Adjusting the VolumeSelecting the Front Speakers Turn Source Selector toMuting the Sound Attenuating the Input SignalAdjusting the Subwoofer Output Level Reinforcing the BassSetting the Subwoofer Information Basic SettingsAdjusting the Front Speaker Output Balance Recording a SourceSetting the Speakers for the DSP Modes Press Setting repeatedly untilRear Delay appears on Display LFE ATT Low Frequency Effect Attenuator appears on Display Crossover FRQ Crossover Frequency appears on the displayTurn Multi JOG to select Low frequency effect attenuator LevelDigital Input Digital in Terminal Setting Selecting the Analog or Digital Input ModeShowing the Text Information on Display Adjust the sound using the functions listed above Using the Sleep TimerPress ONE Touch OPERATION. Onetouchoperation Using Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Assigning Names to Preset Stations Selecting the FM Reception ModePress PTY Search while Using the RDS Radio Data System to Receive FM StationsSearching for a Program by PTY Codes Listening to an FM stationTurn Multi JOG until the PTY Press PTY Search while listening to an FM stationPTY codes Program type appears on Display Switching to a Broadcast Program of Your Choice TemporarilyPress EON so that the last selected Press TA/NEWS/INFO untilCreating Your Own SEA Mode Using the SEA ModesSelecting Your Favorite SEA Mode Press SEA Adjust repeatedlyUsing the DSP Modes 3D-PHONIC modesDAP modes DVD Multi Playback Mode Surround modesAvailable DSP modes By pressing DSP Mode By pressing Surround ModeAvailable DSP Modes According to the Speaker Arrangement FrontAdjusting the 3D-PHONIC Modes Adjusting the DAP ModesAdjusting the Surround Modes JVC Theater Surround adjustments Press Test again to stop the test tone. TestRepeatedly until Theater Appears on the display Activating the DSP Modes To cancel the Dolby/DTS/MPEG Surround modeTheater appears on Display Select and play a sound sourceWant appears on the display Repeatedly until the DSP mode youTo cancel the DSP mode For the other DSP modesPress DVD Multi so that DVD Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Multi appears on the displayUsing the On-Screen Menus Press %/ Þto move to Sound CONTROL, then press @/ # Press @/ #to adjustInput Attenuator mode To BAL. Balance@/ # To SEA ModeTo Surround LEVEL, then press Press %/ Þto move To SEA, then pressPress %/ Þto move to SETTING, then Press @/ # Press %/ Þ/ @/ #to adjust the SEA mode as you wantPress SET to store the setting into the SEA Usermode Set or adjust, then press @/ #Press %/ Þto move to Tuner CONTROL, then press @/ # Press %/ Þto move to Preset Name Then press SETTo Preset Press %/ Þ / @/ #to Move in front of a character you wantSame time Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionDisc Search Only for CD Player Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Title InputTo exit from the Disc information screen Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen Disc Information screen appears on the TVPress %/ Þto move To Performer Then press SET Press Text Display while CD is selected as the sourcePress %/ Þto move To SEARCH, then Press SET Press SET againPress %/ Þto move To Title INPUT, then press SET Press %/ Þto move To Search Then press SETPress %/ Þto move To GENRE, then Press SET Entering the Disc InformationPress %/ Þto move to the genre you want, then press SET Press Text Display while MD is selected as the sourceEnter the disc title Referring to steps 3 Press %/ Þto move To Title Input Then press SETTuner Operating JVC’s Audio/Video ComponentsOperating Audio Components Sound control section AmplifierTurntable CD player-changer7/P Cassette deckChannel + Operating Video ComponentsDVD player 0, 100+Release TV/CATV/DBS If there are more than one code listed for your brand of TVOperating Other Manufacturers’ Video Equipment Try to operate your TV by pressing TV/CATV DBSTry to operate your VCR by pressing VCR If there are more than one code listed for your brandRelease VCR RECManufacturers’ codes for TV Manufacturers’ codes for DBS tuner Manufacturers’ codes for Catv converters Manufacturers’ codes for VCRESC ITVNEC Troubleshooting Problem Possible Cause SolutionAudio SpecificationsAmplifier VideoFM tuner IHF AM MW/LW tunerGeneral EN, GE, FR, NL, SP, IT 0400HIMMDWJEIN

RX-7000RBK specifications

The JVC RX-7000RBK is a high-quality AV receiver that combines sophisticated technology with user-friendly features, making it a popular choice among audio enthusiasts and home theater setups. This receiver is designed to deliver superior sound performance while providing a host of options to cater to diverse audio and video formats.

At the heart of the RX-7000RBK is a robust amplifier capable of producing 100 watts per channel, ensuring powerful output that can fill any room with rich, dynamic sound. The receiver supports a variety of audio channels, allowing users to experience multi-channel surround sound, enhancing the overall cinematic experience whether you’re watching movies or listening to music.

One of the standout features of the RX-7000RBK is its compatibility with various surround sound formats. It supports Dolby Digital, DTS, and other advanced audio technologies, providing an immersive listening experience. The receiver also features a built-in Digital Signal Processor (DSP) that offers numerous sound modes to optimize audio playback, allowing users to tailor the sound to their preferences and the content being played.

Connectivity is another significant attribute of the RX-7000RBK. The receiver includes multiple HDMI inputs, allowing users to connect various devices like Blu-ray players, gaming consoles, and streaming devices. This versatility ensures that users can easily switch between different sources without hassle. Additionally, it features analog inputs, optical and coaxial digital audio inputs, and a USB port for compatibility with a wide range of audio devices.

The RX-7000RBK also comes equipped with an FM/AM tuner, expanding its versatility by allowing users to enjoy their favorite radio stations. The receiver is designed with an intuitive onboard interface that makes navigation seamless, while the included remote control allows users to manage settings from a distance.

Another notable technology integrated into the RX-7000RBK is its energy-saving mode, which reduces power consumption when the receiver is not in use. This feature ensures that users can enjoy high-performance audio without worrying about excessive energy use.

Overall, the JVC RX-7000RBK is an exceptional AV receiver that combines powerful audio performance with a range of features and modern technologies. Its ability to support various audio formats, extensive connectivity options, and user-friendly design makes it a strong contender for anyone looking to enhance their home entertainment experience. Whether for film, music, or gaming, the RX-7000RBK delivers a versatile and enjoyable audio experience.
Top Page Image Contents