JVC RX-7000RBK manual Assigning Names to Preset Stations, Selecting the FM Reception Mode

RETURN

SEA MODE

CNTR TONE

10

1

TEST

4

EFFECT 7/P

To tune in a preset station

On the front panel:

1.Turn SOURCE SELECTOR to select the band (FM or AM —

MW/LW).

The last received station of the selected band is tuned in.

2.Press TUNER PRESET.

3.Turn MULTI JOG until you find the channel you want.

•Turning it clockwise increases the channel numbers.

•Turning it counterclockwise decreases the channel numbers.

From the remote control:

1.Press FM/AM.

•Each time you press the button, the band alternates between FM and AM (MW/LW).

2.Press the 10 keys to select a preset channel number.

•For channel number 5, press 5.

•For channel number 15, press +10 then 5.

•For channel number 20, press +10 then 10.

•For channel number 30, press +10, +10, then 10.

Note:

SOURCE SELECTOR

TUNER PRESET

MULTI JOG

FM/AM

CENTER

2 3

MENU

REAR-L

5 6

ENTER

REAR-R

8 9

SUBWOOFER

0+10

FM MODE 100+

Note:

When using the FM MODE button on the remote control, be sure that the 10 keys are activated for the tuner, not for the CD and others. (See page 45.)

Assigning Names to Preset Stations

You can assign a name of up to four characters to each preset station. When a preset station is tuned in, its assigned name will appear on the display.

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

•You can use the following characters: Space (_), A – Z, and 0 – 9.

On the front panel ONLY:

1. Tune in a preset station.

See the left.

2. Press TUNER (/SEA) MEMORY. TUNER/SEA MEMORY

The preset channel number starts flashing for about 10 seconds.

•If you turn MULTI JOG while the preset channel number is flashing, you can change the preset channel number.

3. Press TUNER PRESET, while the	TUNER PRESET
preset channel number is flashing.

English

When you use the 10 keys on the remote control, be sure that they are activated for the tuner, not for the CD and others. (See page 45.)

Selecting the FM Reception Mode

When an FM stereo broadcast is hard to receive or noisy

You can change the FM reception mode while receiving an FM broadcast.

• You can store the FM reception mode for each preset station.

Press FM MODE on the front panel or on the remote control.

•Each time you press the button, the FM reception mode alternates between “AUTO MUTING” and “MONO.”

FM MODE

SUBWOOFER

	0
	FM MODE
On the front panel	On the remote control

The first character position starts flashing.

4.Turn MULTI JOG to select the first character, while the first character position is flashing.

5.Press TUNER PRESET, while a

character you want is flashing.

The next character position starts flashing.

6.Repeat steps 4 and 5 to enter up to four characters.

MULTI JOG

TUNER PRESET

AUTO MUTING: When a program is broadcasted in stereo, you will hear stereo sound; when in monaural, you will hear monaural sounds. This mode is also useful to suppress static noise between stations. The AUTO MUTING indicator lights up on the display.

MONO: Reception will be improved although you will lose the stereo effect. In this mode, you will hear noise while tuning into the stations. The AUTO MUTING indicator goes off on the display.

7. Press TUNER (/SEA) MEMORY	TUNER/SEA MEMORY
while the last selected character is
flashing after you have assigned a
name.

To erase the input characters

Insert spaces using the same procedure described above.

20