JVC RX-7000RBK manual Troubleshooting, Problem Possible Cause Solution

Page 57

Troubleshooting

Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center.

 

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

 

 

 

 

 

 

 

 

 

The display does not light up.

The power cord is not plugged in.

Plug the power cord into an AC outlet.

 

 

 

 

 

 

 

 

 

 

No sound from speakers.

Speaker signal cables are not connected.

Check speaker wiring and reconnect if

 

 

 

 

necessary.

 

 

 

 

 

 

 

 

 

 

 

 

 

The SPEAKERS 1 and 2 buttons are not

Press SPEAKERS 1 and 2 correctly.

 

 

 

set correctly.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

An incorrect source is selected.

Select the correct source.

 

 

 

 

 

 

 

 

 

 

 

 

 

Muting is activated.

Press MUTING to cancel the mute.

 

 

 

 

 

 

 

 

 

 

Sound from one speaker only.

Speaker signal cables are not connected

Check speaker wiring and reconnect if

 

 

 

properly.

necessary.

 

 

 

 

 

 

 

 

 

 

 

 

 

The balance is set to one extreme.

Adjust the balance properly (see page 13).

 

 

 

 

 

 

 

 

 

 

Continuous hiss or buzzing during FM

Incoming signal is too weak.

Connect an outdoor FM antenna or contact

 

 

reception.

 

your dealer.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The station is too far away.

Select a new station.

 

 

 

 

 

 

 

 

 

 

 

 

 

An incorrect antenna is used.

Check with your dealer to be sure you have

 

 

 

 

the correct antenna.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Antennas are not connected properly.

Check connections.

 

 

 

 

 

 

 

 

 

 

 

 

Occasional cracking noise during FM

Ignition noise from automobiles.

Move the antenna farther from automobile

 

 

reception.

 

traffic.

 

 

 

 

 

 

 

 

 

 

 

 

No colors on the on-screen display.

The color system of the connected TV is

Connect PAL- or multi-color system TV.

 

 

 

not PAL.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Howling during record playing.

Your turntable is too close to speakers.

Move speakers away from the turntable.

 

 

 

 

 

 

 

 

 

 

 

“OVERLOAD” starts flashing on the

Speakers are overloaded because of high

1. Press STANDBY/ON

 

on the front

 

 

 

 

 

 

 

 

display.

volume.

panel to turn off the receiver.

 

 

 

 

2. Stop the playback source.

 

 

 

 

3. Turn on the receiver again, and adjust the

 

 

 

 

volume.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Speakers are overloaded because of short

 

 

on the front panel,

 

 

 

Press STANDBY/ON

 

 

 

 

 

 

 

 

 

 

 

circuit of speaker terminals.

then check the speaker wiring.

 

 

 

 

If “OVERLOAD” does not disappear, unplug

 

 

 

 

the AC power cord, then plug it back again.

 

 

 

 

If speaker wiring is not short-circuited, contact

 

 

 

 

your dealer.

 

 

 

 

 

 

 

 

 

 

 

 

Remote control does not work.

The remote control mode selector is not

Set the selector correctly either to “AUDIO/

 

 

 

set correctly.

TV/VCR” or to “CATV/DBS.”

 

 

 

 

 

 

 

 

 

 

 

 

There is an obstruction in front of the

Remove the obstruction.

 

 

 

 

 

remote sensor on the receiver.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Batteries are weak.

Replace batteries.

 

 

 

 

 

 

 

 

 

 

 

 

English

54

Page 56 Page 58
Image 57
Page 56 Page 58
Contents RX-7000RBK Achtung -- STANDBY/ON -Schalter Per I’ltaliaEspañol Italiano Table of Contents Remote Control Parts IdentificationFront Panel Checking the Supplied Accessories Before InstallationConnecting the FM and AM MW/LW Antennas Getting StartedBasic connecting procedure Connecting the SpeakersConnecting the front speakers AM MW/LW Antenna ConnectionsConnecting the rear and center speakers Connecting Audio/Video ComponentsConnecting the subwoofer speaker About the speaker impedanceCD player Cassette deck or MD recorderVideo component connections DVD player TV and/or DBS tunerDVD player DBS tunerDigital connections Digital input terminalsDigital output terminal Putting Batteries in the Remote Control Connecting the Power CordPlug the power cord into an AC outlet R6PSUM-3/AA15FFrom the remote control Turning the Power On and Off StandbyBasic Operations Selecting the Source to PlaySelecting the Front Speakers Adjusting the VolumeEtc Turn Source Selector toAdjusting the Subwoofer Output Level Attenuating the Input SignalMuting the Sound Reinforcing the BassAdjusting the Front Speaker Output Balance Basic SettingsSetting the Subwoofer Information Recording a SourceSetting the Speakers for the DSP Modes Press Setting repeatedly untilRear Delay appears on Display Turn Multi JOG to select Crossover FRQ Crossover Frequency appears on the displayLFE ATT Low Frequency Effect Attenuator appears on Display Low frequency effect attenuator LevelSelecting the Analog or Digital Input Mode Digital Input Digital in Terminal SettingShowing the Text Information on Display Adjust the sound using the functions listed above Using the Sleep TimerPress ONE Touch OPERATION. Onetouchoperation Using Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Selecting the FM Reception Mode Assigning Names to Preset StationsSearching for a Program by PTY Codes Using the RDS Radio Data System to Receive FM StationsPress PTY Search while Listening to an FM stationTurn Multi JOG until the PTY Press PTY Search while listening to an FM stationPTY codes Press EON so that the last selected Switching to a Broadcast Program of Your Choice TemporarilyProgram type appears on Display Press TA/NEWS/INFO untilSelecting Your Favorite SEA Mode Using the SEA ModesCreating Your Own SEA Mode Press SEA Adjust repeatedlyUsing the DSP Modes 3D-PHONIC modesDAP modes Surround modes DVD Multi Playback ModeAvailable DSP Modes According to the Speaker Arrangement By pressing DSP Mode By pressing Surround ModeAvailable DSP modes FrontAdjusting the DAP Modes Adjusting the 3D-PHONIC ModesAdjusting the Surround Modes JVC Theater Surround adjustments Press Test again to stop the test tone. TestRepeatedly until Theater Appears on the display Theater appears on Display To cancel the Dolby/DTS/MPEG Surround modeActivating the DSP Modes Select and play a sound sourceTo cancel the DSP mode Repeatedly until the DSP mode youWant appears on the display For the other DSP modesActivating the DVD Multi Playback Mode Using the DVD Multi Playback ModePress DVD Multi so that DVD Multi appears on the displayUsing the On-Screen Menus Input Attenuator mode Press @/ #to adjustPress %/ Þto move to Sound CONTROL, then press @/ # To BAL. BalanceTo Surround LEVEL, then press To SEA Mode@/ # Press %/ Þto move To SEA, then pressPress SET to store the setting into the SEA Usermode Press %/ Þ/ @/ #to adjust the SEA mode as you wantPress %/ Þto move to SETTING, then Press @/ # Set or adjust, then press @/ #To Preset Press %/ Þto move to Preset Name Then press SETPress %/ Þto move to Tuner CONTROL, then press @/ # Press %/ Þ / @/ #to Move in front of a character you wantRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemSame time Automatic Source SelectionDisplaying the Disc Information on the TV screen Text Compu Link Remote Control SystemDisc Search Only for CD Player Disc Title InputShowing the Disc Information on the TV Screen Press Text Display while CD or MD is selected as the sourceTo exit from the Disc information screen Disc Information screen appears on the TVPress %/ Þto move To SEARCH, then Press SET Press Text Display while CD is selected as the sourcePress %/ Þto move To Performer Then press SET Press SET againPress %/ Þto move To GENRE, then Press SET Press %/ Þto move To Search Then press SETPress %/ Þto move To Title INPUT, then press SET Entering the Disc InformationEnter the disc title Referring to steps 3 Press Text Display while MD is selected as the sourcePress %/ Þto move to the genre you want, then press SET Press %/ Þto move To Title Input Then press SETOperating Audio Components Operating JVC’s Audio/Video ComponentsTuner Sound control section Amplifier7/P CD player-changerTurntable Cassette deckDVD player Operating Video ComponentsChannel + 0, 100+Operating Other Manufacturers’ Video Equipment If there are more than one code listed for your brand of TVRelease TV/CATV/DBS Try to operate your TV by pressing TV/CATV DBSRelease VCR If there are more than one code listed for your brandTry to operate your VCR by pressing VCR RECManufacturers’ codes for TV Manufacturers’ codes for DBS tuner Manufacturers’ codes for VCR Manufacturers’ codes for Catv convertersESC ITVNEC Problem Possible Cause Solution TroubleshootingAmplifier SpecificationsAudio VideoFM tuner IHF AM MW/LW tunerGeneral EN, GE, FR, NL, SP, IT 0400HIMMDWJEIN

RX-7000RBK specifications

The JVC RX-7000RBK is a high-quality AV receiver that combines sophisticated technology with user-friendly features, making it a popular choice among audio enthusiasts and home theater setups. This receiver is designed to deliver superior sound performance while providing a host of options to cater to diverse audio and video formats.

At the heart of the RX-7000RBK is a robust amplifier capable of producing 100 watts per channel, ensuring powerful output that can fill any room with rich, dynamic sound. The receiver supports a variety of audio channels, allowing users to experience multi-channel surround sound, enhancing the overall cinematic experience whether you’re watching movies or listening to music.

One of the standout features of the RX-7000RBK is its compatibility with various surround sound formats. It supports Dolby Digital, DTS, and other advanced audio technologies, providing an immersive listening experience. The receiver also features a built-in Digital Signal Processor (DSP) that offers numerous sound modes to optimize audio playback, allowing users to tailor the sound to their preferences and the content being played.

Connectivity is another significant attribute of the RX-7000RBK. The receiver includes multiple HDMI inputs, allowing users to connect various devices like Blu-ray players, gaming consoles, and streaming devices. This versatility ensures that users can easily switch between different sources without hassle. Additionally, it features analog inputs, optical and coaxial digital audio inputs, and a USB port for compatibility with a wide range of audio devices.

The RX-7000RBK also comes equipped with an FM/AM tuner, expanding its versatility by allowing users to enjoy their favorite radio stations. The receiver is designed with an intuitive onboard interface that makes navigation seamless, while the included remote control allows users to manage settings from a distance.

Another notable technology integrated into the RX-7000RBK is its energy-saving mode, which reduces power consumption when the receiver is not in use. This feature ensures that users can enjoy high-performance audio without worrying about excessive energy use.

Overall, the JVC RX-7000RBK is an exceptional AV receiver that combines powerful audio performance with a range of features and modern technologies. Its ability to support various audio formats, extensive connectivity options, and user-friendly design makes it a strong contender for anyone looking to enhance their home entertainment experience. Whether for film, music, or gaming, the RX-7000RBK delivers a versatile and enjoyable audio experience.
Top Page Image Contents