JVC RX-7000RBK Connecting the Speakers, AM MW/LW Antenna Connections, Basic connecting procedure

Page 7

AM (MW/LW) Antenna Connections

Snap the tabs on the loop into the

ANTENNA

slots of the base to assemble the

FM 75

AM (MW/LW) loop.

COAXIAL

 

AM

LOOP

AM (MW/LW) Loop Antenna

AM

EXT

123

Outdoor single vinyl-covered wire

Turn the loop until you have the best reception.

Notes:

•Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.

•If reception is poor, connect an outdoor single vinyl-covered wire to the AM EXT terminal. (Keep the AM (MW/LW) loop antenna connected.)

Connecting the Speakers

You can connect the following speakers:

•Two pairs of front speakers to produce normal stereo sound.

•One pair of rear speakers to enjoy the surround effect.

•One center speaker to produce more effective surround effect (to emphasize human voices).

•One subwoofer to enhance the bass.

IMPORTANT:

After connecting the speakers listed above, set the speaker setting information properly to obtain the best possible DSP effect. For details, see page 14.

For each speaker (except for a subwoofer), connect the (–) and (+) terminals on the rear panel to the (–) and (+) terminals marked on the speakers. For connecting a subwoofer, see page 5.

CAUTION:

Use speakers with the SPEAKER IMPEDANCE indicated by the speaker terminals.

Basic connecting procedure

1

2

3

 

4

 

 

1

1

 

1

 

 

RI

RIG

 

RIG

 

 

GH

HT

HT

 

T

 

 

1Cut, twist and remove the insulation at the end of each speaker signal cable (not supplied).

2Turn the knob counterclockwise.

3Insert the speaker signal cable.

4Turn the knob clockwise.

Connecting the front speakers

You can connect two pairs of front speakers (one pair to the FRONT SPEAKERS 1 terminals, and another pair to the FRONT SPEAKERS 2 terminals).

Right speaker

 

FRONT SPEAKERS 1

 

Left speaker

 

 

1

1

+

–

–

+

2

2

RIGHTLEFT

FRONT SPEAKERS

Right speaker

 

FRONT SPEAKERS 2

 

Left speaker

 

 

English

4

Page 6 Page 8
Image 7
Page 6 Page 8
Contents RX-7000RBK Achtung -- STANDBY/ON -Schalter Per I’ltaliaEspañol Italiano Table of Contents Parts Identification Remote ControlFront Panel Getting Started Before InstallationChecking the Supplied Accessories Connecting the FM and AM MW/LW AntennasAM MW/LW Antenna Connections Connecting the SpeakersBasic connecting procedure Connecting the front speakersAbout the speaker impedance Connecting Audio/Video ComponentsConnecting the rear and center speakers Connecting the subwoofer speakerCassette deck or MD recorder CD playerVideo component connections DBS tuner TV and/or DBS tunerDVD player DVD playerDigital input terminals Digital connectionsDigital output terminal R6PSUM-3/AA15F Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletSelecting the Source to Play Turning the Power On and Off StandbyFrom the remote control Basic OperationsTurn Source Selector to Adjusting the VolumeSelecting the Front Speakers EtcReinforcing the Bass Attenuating the Input SignalAdjusting the Subwoofer Output Level Muting the SoundRecording a Source Basic SettingsAdjusting the Front Speaker Output Balance Setting the Subwoofer InformationPress Setting repeatedly until Setting the Speakers for the DSP ModesRear Delay appears on Display Low frequency effect attenuator Level Crossover FRQ Crossover Frequency appears on the displayTurn Multi JOG to select LFE ATT Low Frequency Effect Attenuator appears on DisplaySelecting the Analog or Digital Input Mode Digital Input Digital in Terminal SettingShowing the Text Information on Display Using the Sleep Timer Adjust the sound using the functions listed abovePress ONE Touch OPERATION. Onetouchoperation Tuning in Stations Manually Using Preset TuningReceiving Radio Broadcasts Selecting the FM Reception Mode Assigning Names to Preset StationsListening to an FM station Using the RDS Radio Data System to Receive FM StationsSearching for a Program by PTY Codes Press PTY Search whilePress PTY Search while listening to an FM station Turn Multi JOG until the PTYPTY codes Press TA/NEWS/INFO until Switching to a Broadcast Program of Your Choice TemporarilyPress EON so that the last selected Program type appears on DisplayPress SEA Adjust repeatedly Using the SEA ModesSelecting Your Favorite SEA Mode Creating Your Own SEA Mode3D-PHONIC modes Using the DSP ModesDAP modes Surround modes DVD Multi Playback ModeFront By pressing DSP Mode By pressing Surround ModeAvailable DSP Modes According to the Speaker Arrangement Available DSP modesAdjusting the DAP Modes Adjusting the 3D-PHONIC ModesAdjusting the Surround Modes Press Test again to stop the test tone. Test JVC Theater Surround adjustmentsRepeatedly until Theater Appears on the display Select and play a sound source To cancel the Dolby/DTS/MPEG Surround modeTheater appears on Display Activating the DSP ModesFor the other DSP modes Repeatedly until the DSP mode youTo cancel the DSP mode Want appears on the displayMulti appears on the display Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Press DVD Multi so that DVDUsing the On-Screen Menus To BAL. Balance Press @/ #to adjustInput Attenuator mode Press %/ Þto move to Sound CONTROL, then press @/ #Press %/ Þto move To SEA, then press To SEA ModeTo Surround LEVEL, then press @/ #Set or adjust, then press @/ # Press %/ Þ/ @/ #to adjust the SEA mode as you wantPress SET to store the setting into the SEA Usermode Press %/ Þto move to SETTING, then Press @/ #Press %/ Þ / @/ #to Move in front of a character you want Press %/ Þto move to Preset Name Then press SETTo Preset Press %/ Þto move to Tuner CONTROL, then press @/ #Automatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Same timeDisc Title Input Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerDisc Information screen appears on the TV Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen To exit from the Disc information screenPress SET again Press Text Display while CD is selected as the sourcePress %/ Þto move To SEARCH, then Press SET Press %/ Þto move To Performer Then press SETEntering the Disc Information Press %/ Þto move To Search Then press SETPress %/ Þto move To GENRE, then Press SET Press %/ Þto move To Title INPUT, then press SETPress %/ Þto move To Title Input Then press SET Press Text Display while MD is selected as the sourceEnter the disc title Referring to steps 3 Press %/ Þto move to the genre you want, then press SETSound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCassette deck CD player-changer7/P Turntable0, 100+ Operating Video ComponentsDVD player Channel +Try to operate your TV by pressing TV/CATV DBS If there are more than one code listed for your brand of TVOperating Other Manufacturers’ Video Equipment Release TV/CATV/DBSREC If there are more than one code listed for your brandRelease VCR Try to operate your VCR by pressing VCRManufacturers’ codes for TV Manufacturers’ codes for DBS tuner Manufacturers’ codes for VCR Manufacturers’ codes for Catv convertersITV ESCNEC Problem Possible Cause Solution TroubleshootingVideo SpecificationsAmplifier AudioAM MW/LW tuner FM tuner IHFGeneral EN, GE, FR, NL, SP, IT 0400HIMMDWJEIN

RX-7000RBK specifications

The JVC RX-7000RBK is a high-quality AV receiver that combines sophisticated technology with user-friendly features, making it a popular choice among audio enthusiasts and home theater setups. This receiver is designed to deliver superior sound performance while providing a host of options to cater to diverse audio and video formats.

At the heart of the RX-7000RBK is a robust amplifier capable of producing 100 watts per channel, ensuring powerful output that can fill any room with rich, dynamic sound. The receiver supports a variety of audio channels, allowing users to experience multi-channel surround sound, enhancing the overall cinematic experience whether you’re watching movies or listening to music.

One of the standout features of the RX-7000RBK is its compatibility with various surround sound formats. It supports Dolby Digital, DTS, and other advanced audio technologies, providing an immersive listening experience. The receiver also features a built-in Digital Signal Processor (DSP) that offers numerous sound modes to optimize audio playback, allowing users to tailor the sound to their preferences and the content being played.

Connectivity is another significant attribute of the RX-7000RBK. The receiver includes multiple HDMI inputs, allowing users to connect various devices like Blu-ray players, gaming consoles, and streaming devices. This versatility ensures that users can easily switch between different sources without hassle. Additionally, it features analog inputs, optical and coaxial digital audio inputs, and a USB port for compatibility with a wide range of audio devices.

The RX-7000RBK also comes equipped with an FM/AM tuner, expanding its versatility by allowing users to enjoy their favorite radio stations. The receiver is designed with an intuitive onboard interface that makes navigation seamless, while the included remote control allows users to manage settings from a distance.

Another notable technology integrated into the RX-7000RBK is its energy-saving mode, which reduces power consumption when the receiver is not in use. This feature ensures that users can enjoy high-performance audio without worrying about excessive energy use.

Overall, the JVC RX-7000RBK is an exceptional AV receiver that combines powerful audio performance with a range of features and modern technologies. Its ability to support various audio formats, extensive connectivity options, and user-friendly design makes it a strong contender for anyone looking to enhance their home entertainment experience. Whether for film, music, or gaming, the RX-7000RBK delivers a versatile and enjoyable audio experience.
Top Page Image Contents