JVC RX-D302B Adjust the volume, Selecting the digital decode mode, Listening with headphones

Page 17

3 Adjust the volume

To increase the volume, turn MASTER VOLUME control clockwise (or press VOLUME + on the remote control).

To decrease the volume, turn MASTER VOLUME control counterclockwise (or press VOLUME – on the remote control).

When you adjust the volume, the volume level indication appears on the display for a while.

ANALOG

AUTO SURR

LR

S.WFR

Selecting the digital decode mode

If the following symptoms occur while playing Dolby Digital or DTS software with “DGTL AUTO” selected (see page 14), follow the procedure below:

Sound does not come out at the beginning of playback.

Noise comes out while searching for or skipping chapters or tracks.

From the remote control ONLY:

Press DECODE MODE to select “DOLBY DIGITAL” or “DTS.”

Each time you press DECODE MODE, the digital decode mode changes as follows:

AUTO SURR

DIGITAL

L C R

DIGITAL

S.WFR LFE

CAUTION:

Always set the volume to the minimum before starting any sources. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.

NOTE

The volume level can be adjusted within the range of “0” (minimum) to “50” (maximum).

Listening with headphones

You can enjoy not only stereo software but also multi-channel software through the headphones. (Sounds are down-mixed to the front channels while playing multi-channel software.)

Connect a pair of headphones to the PHONES jack on the front panel to activate the HEADPHONE mode.

The HEADPHONE indicator lights up on the display.

You can also enjoy the Surround/DSP mode through the headphones—3D HEADPHONE mode. For details, see page 30.

Disconnecting a pair of headphones from the PHONES jack cancels the HEADPHONE (or 3D HEADPHONE) mode and activates the speakers.

CAUTION:

Be sure to turn down the volume:

Before connecting or putting on headphones, as high volume can damage both the headphones and your hearing.

Before removing headphones, as high volume may output from the speakers.

LS RS

DGTL AUTO DOLBY DIGITAL

DTS (Back to the beginning)

To play back software encoded with Dolby Digital, select “DOLBY DIGITAL.”

To play back software encoded with DTS, select “DTS.”

NOTE

“DOLBY DIGITAL” or “DTS” is automatically reset to “DGTL AUTO” in the following cases:

-When you turn off the receiver.

-When you select another source.

-When you select “DGTL AUTO” again by pressing ANALOG/ DIGITAL.

The following digital signal format indicators on the display indicate what type of signal comes into the receiver.

LINEAR PCM: Lights up when Linear PCM signal comes in.

: • Lights up when Dolby Digital signal comes in.

Flashes when “DOLBY DIGITAL” is selected for any software other than Dolby Digital.

:• Lights up when conventional DTS signal comes in.

Flashes when “DTS” is selected for any software other than DTS.

96/24: Lights up when DTS 96/24 signal comes in.

NOTE

When “DGTL AUTO” cannot recognize the incoming signal, no digital signal format indicator lights up on the display.

Turning off the sounds temporarily

From the remote control ONLY:

Press MUTING to turn off the sound through all connected speakers and headphones.

“MUTING” appears on the display and the volume turns off.

ANALOG

AUTO SURR

LR

S.WFR

To restore the sound, press MUTING again.

Pressing VOLUME +/– (or turning MASTER VOLUME control on the front panel) also restores the sound.

15

Image 17
Contents For Customer Use RX-D301S / RX-D302BFor U.S.A For Canada/pour le CanadaFor Canada/pour le Canada Table of Contents Parts identification Remote controlWhen operating a DVD player, set the mode selector u to DVD Rear panel Front panelDisplay window Putting batteries in the remote control Before InstallationChecking the supplied accessories Getting startedAntenna Connecting the FM and AM antennasFM antenna connection Speaker Layout Diagram Connecting the speakersConnecting the speakers Connecting the powered subwooferTurn off all components before making connections Connecting video componentsOnly for DVD recorder To S-video input If your video components have AV Compu Link terminalAbout DVD Multi È ÔVCR Å Blue Red Connecting a TVGreen Digital connection About video signal conversionDigital input terminals Digital output terminalFor USB Terminal USB ConnectionConnecting the power cord To turn off the power into standby Turn on the powerSelecting the analog or digital input mode Basic operationsSelecting the digital decode mode Adjust the volumeListening with headphones To restore the sound, press Muting againBasic adjustment of auto memory Turning off the power with the Sleep TimerSignal and speaker indicators on the display Changing the display brightnessPress Setting Basic settingsPress SET Before you start, rememberRoom size and the speaker distance/output level Basic setting itemsSpeakers channels number and the size Setting subwoofer information-SUBWOOFER Setting the speakersSetting the surround back speakers-S Back OUT Turn Multi JOG to select the appropriate settingSetting the speaker distance Activating the EX/ES/PLIIx setting- EX/ES/PLIIxFrom the remote control AutoSelecting the main or sub channel Setting bass soundUsing the Midnight mode DVD S/C Memorizing the volume level for each source-ONE Touch OPEVCR S/C OnetouchonOperating procedure Sound adjustmentsBasic adjustment items Press Test to check the speakers’ output balance Adjusting the speaker output levelsAttenuating the input signal-INPUT ATT Adjusting the bass soundsAdjusting the virtual room size for DSP modes Adjusting the liveness effect for DSP modesAdjusting the center tone-CENTER Tone Using preset tuning Tuning in to stations manuallyTo store the preset stations Tuner operationsTo tune in a preset station Selecting the FM reception modeReproducing theater ambience Creating realistic sound fieldsIntroducing the Surround modes Dolby DigitalDTS 3D Headphone modeAbout other digital signals Digital Acoustic Processor DAP modes All Channel Stereo mode ALL CH StereoIntroducing the DSP modes DTSDolby Digital Incoming Signal Type Using the Surround/DSP modesAbout the DSP modes Virtual Surround BackTurn Multi JOG to select the Surround/DSP mode you want When you select Auto SurroundSelecting the Surround/DSP modes Select and play any source other than DVD MultiConnections 1 AV Compu Link connection AV Compu Link remote control systemConnections 2 Video cable connection CaseAutomatic selection of TV’s input mode Connecting procedureAutomatic power on/off One-touch video playVCR Operating other JVC productsChannel + REWDVD recorder or DVD player Changing the remote control code for DVD recorderRelease DVR/DVD TOP MENU/MENUOperating other manufacturers’ products Changing the transmittable signals for operating a TVRelease TV Try to operate your TV by pressing TVRelease VCR Changing the transmittable signals for operating a VCRTry to operate your VCR by pressing VCR Manufacturers’ codes for VCRManufacturers’ codes for Catv converter Release DBS/CATVManufacturers’ codes for DBS tuner Try to operate your DVD player by pressing DVR/DVDPower TroubleshootingProblem Possible Cause Solution Remote control TunerAmplifier SpecificationsFM tuner IHF AM tunerPage Page Audio Video Control Receiver RX-D302B Mises en garde, précautions et indications diverses English Parts identification ID Learning 1DVR/DVD Getting started AM antenna connection Connecting the speakers Connecting video components È Ô Red White Component video cable not suppliedDBS tuner Video cable not suppliedAbout video signal conversion USB wireless Transmitter supplied Connecting the power cord Basic operations Auto Surr Digital Changing the display brightness Basic settings Basic setting items Setting the speakers Activating the EX/ES/PLIIx setting- EX/ES/PLIIx Dual Mono DBS Video Sound adjustments Adjusting the speaker output levels Adjusting the bass sounds Dimension Tuner operations Selecting the FM reception mode Creating realistic sound fields DTS Introducing the DSP modes Digital When activating NEO6 MUSIC, you can adjust Center RX-D302B Equipment To video input Connecting procedure Operating other JVC products DVD recorder or DVD player Operating other manufacturers’ products English Release DBS/CATV There are any problems you cannot solve, contact your JVC’s Specifications RX-D302B