JVC RX-D302B, RX-D301S manual Specifications

Page 91

English

Specifications

Designs and specifications are subject to change without notice.

Amplifier

Output Power

At stereo operation:

Front channels: 110 W per channel, min. RMS, driven into 6 Ω at 40 Hz to 20 kHz with no more than 0.8% total harmonic distortion.

At surround operation:

Front channels:

110 W per channel, min. RMS, driven into

 

6 Ω at 1 kHz with no more than 0.8% total

 

harmonic distortion.

Center channel:

110 W, min. RMS, driven into 6 Ω at 1 kHz,

 

with no more than 0.8% total harmonic

 

distortion.

Surround channels: 110 W per channel, min. RMS, driven into 6 Ω at 1 kHz, with no more than 0.8% total harmonic distortion.

Surround back channels:

110 W per channel, min. RMS, driven into 6 Ω at 1 kHz, with no more than 0.8% total harmonic distortion.

Audio

Audio Input Sensitivity/Impedance:

DVR/DVD (DVD MULTI), VCR, DBS, TV:

270 mV/47 kΩ

Audio Input (DIGITAL IN)*:

Coaxial: DIGITAL IN 1(DVR/DVD):

0.5 V(p-p)/75 Ω

Optical: DIGITAL IN 2(DBS), 3(VCR):

–21 dBm to –15 dBm (660 nm ±30 nm)

USB: USB WIRELESS

USB TERMINAL

*Corresponding to Linear PCM, Dolby Digital, and DTS (with sampling frequency—32 kHz, 44.1 kHz, 48 kHz).

Audio Output Level:

 

 

DVR, VCR:

270 mV

Signal-to-Noise Ratio (’66 IHF/’78 IHF):

80 dB/62 dB

Frequency Response (6 Ω):

20

Hz to 20 kHz (±1 dB)

Bass Boost:

+4 dB ±1 dB at 100 Hz

Equalization (at DSP operation):

Center frequency:

63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz

Control range:

±8 dB

Video

Video Input Sensitivity/Impedance:

Composite video: DVR/DVD, VCR, DBS:

1 V(p-p)/75 Ω

S-video: DVR/DVD, VCR, DBS:

 

Y (luminance):

1 V(p-p)/75 Ω

C (chrominance, burst):

0.286 V(p-p)/75 Ω

Component: DVR/DVD, VCR (DBS):

Y (luminance):

1 V(p-p)/75 Ω

PB, PR:

0.7 V(p-p)/75 Ω

Video Output Level/Impedance:

Composite video: DVR, VCR, MONITOR OUT:

 

1 V(p-p)/75 Ω

S-video: DVR, VCR, MONITOR OUT:

Y (luminance):

1 V(p-p)/75 Ω

C (chrominance, burst):

0.286 V(p-p)/75 Ω

Component: MONITOR OUT:

 

Y (luminance):

1 V(p-p)/75 Ω

PB, PR:

0.7 V(p-p)/75 Ω

Synchronization:

Negative

FM tuner (IHF)

Tuning Range:

87.5 MHz to 108.0 MHz

Usable Sensitivity:

 

Monaural:

12.8 dBf (1.2 µV/75 Ω)

50 dB Quieting Sensitivity:

 

Monaural:

16.0 dBf (1.7 µV/75 Ω)

Stereo:

37.5 dBf (20.5 µV/75 Ω)

Stereo Separation at REC OUT:

35 dB at 1 kHz

AM tuner

Tuning Range:530 kHz to 1 710 kHz

General

Power Requirements:

AC 120 V , 60 Hz

Power Consumption:

150 W/200 VA (at operation)

0.9W (in standby mode)

Dimensions (W x H x D): 435 mm x 91.5 mm x 371 mm

Mass:

6.8 kg

USB WIRELESS SYSTEM

The USB wireless transmitter supplied with this receiver supports Direct Sequence Spreading Spectrum (DSSS) using 2.4 GHz frequency band.

42

Page 90 Page 92
Image 91
Page 90 Page 92
Contents For Customer Use RX-D301S / RX-D302BFor Canada/pour le Canada For Canada/pour le CanadaFor U.S.A Table of Contents When operating a DVD player, set the mode selector u to DVD Remote controlParts identification Display window Front panelRear panel Getting started Before InstallationPutting batteries in the remote control Checking the supplied accessoriesFM antenna connection Connecting the FM and AM antennasAntenna Connecting the powered subwoofer Connecting the speakersSpeaker Layout Diagram Connecting the speakersIf your video components have AV Compu Link terminal Connecting video componentsTurn off all components before making connections Only for DVD recorder To S-video inputAbout DVD Multi È ÔVCR Å Green Connecting a TVBlue Red Digital output terminal About video signal conversionDigital connection Digital input terminalsFor USB Terminal USB ConnectionConnecting the power cord Basic operations Turn on the powerTo turn off the power into standby Selecting the analog or digital input modeTo restore the sound, press Muting again Adjust the volumeSelecting the digital decode mode Listening with headphonesChanging the display brightness Turning off the power with the Sleep TimerBasic adjustment of auto memory Signal and speaker indicators on the displayBefore you start, remember Basic settingsPress Setting Press SETSpeakers channels number and the size Basic setting itemsRoom size and the speaker distance/output level Turn Multi JOG to select the appropriate setting Setting the speakersSetting subwoofer information-SUBWOOFER Setting the surround back speakers-S Back OUTAuto Activating the EX/ES/PLIIx setting- EX/ES/PLIIxSetting the speaker distance From the remote controlUsing the Midnight mode Setting bass soundSelecting the main or sub channel Onetouchon Memorizing the volume level for each source-ONE Touch OPEDVD S/C VCR S/CBasic adjustment items Sound adjustmentsOperating procedure Press Test to check the speakers’ output balance Adjusting the speaker output levelsAdjusting the liveness effect for DSP modes Adjusting the bass soundsAttenuating the input signal-INPUT ATT Adjusting the virtual room size for DSP modesAdjusting the center tone-CENTER Tone Tuner operations Tuning in to stations manuallyUsing preset tuning To store the preset stationsTo tune in a preset station Selecting the FM reception modeDolby Digital Creating realistic sound fieldsReproducing theater ambience Introducing the Surround modesAbout other digital signals 3D Headphone modeDTS Introducing the DSP modes All Channel Stereo mode ALL CH StereoDigital Acoustic Processor DAP modes Virtual Surround Back Using the Surround/DSP modesDTSDolby Digital Incoming Signal Type About the DSP modesSelect and play any source other than DVD Multi When you select Auto SurroundTurn Multi JOG to select the Surround/DSP mode you want Selecting the Surround/DSP modesCase AV Compu Link remote control systemConnections 1 AV Compu Link connection Connections 2 Video cable connectionOne-touch video play Connecting procedureAutomatic selection of TV’s input mode Automatic power on/offREW Operating other JVC productsVCR Channel +TOP MENU/MENU Changing the remote control code for DVD recorderDVD recorder or DVD player Release DVR/DVDTry to operate your TV by pressing TV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Release TVManufacturers’ codes for VCR Changing the transmittable signals for operating a VCRRelease VCR Try to operate your VCR by pressing VCRTry to operate your DVD player by pressing DVR/DVD Release DBS/CATVManufacturers’ codes for Catv converter Manufacturers’ codes for DBS tunerRemote control Tuner TroubleshootingPower Problem Possible Cause SolutionAM tuner SpecificationsAmplifier FM tuner IHFPage Page Audio Video Control Receiver RX-D302B Mises en garde, précautions et indications diverses English Parts identification ID Learning 1DVR/DVD Getting started AM antenna connection Connecting the speakers Connecting video components È Ô Red Video cable not supplied Component video cable not suppliedWhite DBS tunerAbout video signal conversion USB wireless Transmitter supplied Connecting the power cord Basic operations Auto Surr Digital Changing the display brightness Basic settings Basic setting items Setting the speakers Activating the EX/ES/PLIIx setting- EX/ES/PLIIx Dual Mono DBS Video Sound adjustments Adjusting the speaker output levels Adjusting the bass sounds Dimension Tuner operations Selecting the FM reception mode Creating realistic sound fields DTS Introducing the DSP modes Digital When activating NEO6 MUSIC, you can adjust Center RX-D302B Equipment To video input Connecting procedure Operating other JVC products DVD recorder or DVD player Operating other manufacturers’ products English Release DBS/CATV There are any problems you cannot solve, contact your JVC’s Specifications RX-D302B
Top Page Image Contents