JVC RX-D302B, RX-D301S manual Getting started

Page 53

English

Getting started

Before Installation

General precautions

Be sure your hands are dry.

Turn the power off to all components.

Read the manuals supplied with the components you are going to connect.

Locations

Install the receiver in a location that is level and protected from moisture and dust.

The temperature around the receiver must be between –5˚C and 35˚C.

Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.

Leave sufficient distance between the receiver and the TV.

Handling the receiver

Do not insert any metal object into the receiver.

Do not disassemble the receiver or remove screws, covers, or cabinet.

Do not expose the receiver to rain or moisture.

Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.

When you are away on travel or otherwise for an extended period or time, remove the plug from the wall outlet. A small amount of power is always consumed while the power cord is connected to the wall outlet.

The receiver has a built-in cooling fan which operates while the receiver is turned on. Be sure to leave enough ventilation to obtain sufficient cooling effect.

CAUTION:

Do not connect the AC power plug to the wall outlet until all

connections are completed.

Putting batteries in the remote control

Before using the remote control, put two supplied batteries first.

1

2

3

1Press and slide the battery cover on the back of the remote control.

2Insert batteries.

Make sure to match the polarity: (+) to (+) and (–) to (–).

3Replace the cover.

If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6(SUM-3)/AA(15F) type dry-cell batteries.

Supplied butteries are for initial setup. Replace for continued use.

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

Place batteries in the remote control so they match the polarity:

(+) to (+) and (–) to (–).

Use the correct type of batteries. Batteries that look similar may differ in voltage.

Always replace both batteries at the same time.

Do not expose batteries to heat or flame.

When using the remote control, aim the remote control directly at the remote sensor on the front panel.

Remote sensor

Checking the supplied accessories

Check to be sure you have all of the following supplied accessories. If anything is missing, contact your dealer immediately.

Remote control (1)

Batteries (2)

AM loop antenna (1)

FM antenna (1)

USB wireless antenna (1)

USB wireless transmitter (Model number: QAL0708-001) (1)

USB extension cable (60 cm) (1)

4

Image 53
Contents For Customer Use RX-D301S / RX-D302BFor U.S.A For Canada/pour le CanadaFor Canada/pour le Canada Table of Contents Parts identification Remote controlWhen operating a DVD player, set the mode selector u to DVD Rear panel Front panelDisplay window Putting batteries in the remote control Before InstallationChecking the supplied accessories Getting startedAntenna Connecting the FM and AM antennasFM antenna connection Speaker Layout Diagram Connecting the speakersConnecting the speakers Connecting the powered subwooferTurn off all components before making connections Connecting video componentsOnly for DVD recorder To S-video input If your video components have AV Compu Link terminalAbout DVD Multi È ÔVCR Å Blue Red Connecting a TVGreen Digital connection About video signal conversionDigital input terminals Digital output terminalFor USB Terminal USB ConnectionConnecting the power cord To turn off the power into standby Turn on the powerSelecting the analog or digital input mode Basic operationsSelecting the digital decode mode Adjust the volumeListening with headphones To restore the sound, press Muting againBasic adjustment of auto memory Turning off the power with the Sleep TimerSignal and speaker indicators on the display Changing the display brightnessPress Setting Basic settingsPress SET Before you start, rememberRoom size and the speaker distance/output level Basic setting itemsSpeakers channels number and the size Setting subwoofer information-SUBWOOFER Setting the speakersSetting the surround back speakers-S Back OUT Turn Multi JOG to select the appropriate settingSetting the speaker distance Activating the EX/ES/PLIIx setting- EX/ES/PLIIxFrom the remote control AutoSelecting the main or sub channel Setting bass soundUsing the Midnight mode DVD S/C Memorizing the volume level for each source-ONE Touch OPEVCR S/C OnetouchonOperating procedure Sound adjustmentsBasic adjustment items Press Test to check the speakers’ output balance Adjusting the speaker output levelsAttenuating the input signal-INPUT ATT Adjusting the bass soundsAdjusting the virtual room size for DSP modes Adjusting the liveness effect for DSP modesAdjusting the center tone-CENTER Tone Using preset tuning Tuning in to stations manuallyTo store the preset stations Tuner operationsTo tune in a preset station Selecting the FM reception modeReproducing theater ambience Creating realistic sound fieldsIntroducing the Surround modes Dolby DigitalDTS 3D Headphone modeAbout other digital signals Digital Acoustic Processor DAP modes All Channel Stereo mode ALL CH StereoIntroducing the DSP modes DTSDolby Digital Incoming Signal Type Using the Surround/DSP modesAbout the DSP modes Virtual Surround BackTurn Multi JOG to select the Surround/DSP mode you want When you select Auto SurroundSelecting the Surround/DSP modes Select and play any source other than DVD MultiConnections 1 AV Compu Link connection AV Compu Link remote control systemConnections 2 Video cable connection CaseAutomatic selection of TV’s input mode Connecting procedureAutomatic power on/off One-touch video playVCR Operating other JVC productsChannel + REWDVD recorder or DVD player Changing the remote control code for DVD recorderRelease DVR/DVD TOP MENU/MENUOperating other manufacturers’ products Changing the transmittable signals for operating a TVRelease TV Try to operate your TV by pressing TVRelease VCR Changing the transmittable signals for operating a VCRTry to operate your VCR by pressing VCR Manufacturers’ codes for VCRManufacturers’ codes for Catv converter Release DBS/CATVManufacturers’ codes for DBS tuner Try to operate your DVD player by pressing DVR/DVDPower TroubleshootingProblem Possible Cause Solution Remote control TunerAmplifier SpecificationsFM tuner IHF AM tunerPage Page Audio Video Control Receiver RX-D302B Mises en garde, précautions et indications diverses English Parts identification ID Learning 1DVR/DVD Getting started AM antenna connection Connecting the speakers Connecting video components È Ô Red White Component video cable not suppliedDBS tuner Video cable not suppliedAbout video signal conversion USB wireless Transmitter supplied Connecting the power cord Basic operations Auto Surr Digital Changing the display brightness Basic settings Basic setting items Setting the speakers Activating the EX/ES/PLIIx setting- EX/ES/PLIIx Dual Mono DBS Video Sound adjustments Adjusting the speaker output levels Adjusting the bass sounds Dimension Tuner operations Selecting the FM reception mode Creating realistic sound fields DTS Introducing the DSP modes Digital When activating NEO6 MUSIC, you can adjust Center RX-D302B Equipment To video input Connecting procedure Operating other JVC products DVD recorder or DVD player Operating other manufacturers’ products English Release DBS/CATV There are any problems you cannot solve, contact your JVC’s Specifications RX-D302B