JVC RX-D301S manual Getting started, Before Installation, Putting batteries in the remote control

Page 6

Getting started

Before Installation

General precautions

Be sure your hands are dry.

Turn the power off to all components.

Read the manuals supplied with the components you are going to connect.

Locations

Install the receiver in a location that is level and protected from moisture and dust.

The temperature around the receiver must be between –5˚C and 35˚C (23˚F and 95˚F).

Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.

Leave sufficient distance between the receiver and the TV.

Handling the receiver

Do not insert any metal object into the receiver.

Do not disassemble the receiver or remove screws, covers, or cabinet.

Do not expose the receiver to rain or moisture.

Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.

When you are away on travel or otherwise for an extended period or time, remove the plug from the wall outlet. A small amount of power is always consumed while the power cord is connected to the wall outlet.

The receiver has a built-in cooling fan which operates while the receiver is turned on. Be sure to leave enough ventilation to obtain sufficient cooling effect.

CAUTION:

Do not connect the AC power plug to the wall outlet until all

connections are completed.

Putting batteries in the remote control

Before using the remote control, put two supplied batteries first.

1

2

3

1Press and slide the battery cover on the back of the remote control.

2Insert batteries.

Make sure to match the polarity: (+) to (+) and (–) to (–).

3Replace the cover.

If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6(SUM-3)/AA(15F) type dry-cell batteries.

Supplied butteries are for initial setup. Replace for continued use.

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

Place batteries in the remote control so they match the polarity:

(+) to (+) and (–) to (–).

Use the correct type of batteries. Batteries that look similar may differ in voltage.

Always replace both batteries at the same time.

Do not expose batteries to heat or flame.

When using the remote control, aim the remote control directly at the remote sensor on the front panel.

Remote sensor

Checking the supplied accessories

Check to be sure you have all of the following supplied accessories. If anything is missing, contact your dealer immediately.

Remote control (1)

Batteries (2)

AM loop antenna (1)

FM antenna (1)

USB wireless antenna (1)

USB wireless transmitter (Model number: QAL0708-001) (1)

USB extension cable (60cm) (1)

4

Image 6
Contents RX-D301S / RX-D302B For Customer UseFor Canada/pour le Canada For Canada/pour le CanadaFor U.S.A Table of Contents Remote control When operating a DVD player, set the mode selector u to DVDParts identification Front panel Display windowRear panel Checking the supplied accessories Before InstallationPutting batteries in the remote control Getting startedConnecting the FM and AM antennas FM antenna connectionAntenna Connecting the speakers Connecting the speakersSpeaker Layout Diagram Connecting the powered subwooferOnly for DVD recorder To S-video input Connecting video componentsTurn off all components before making connections If your video components have AV Compu Link terminalÈ Ô About DVD MultiVCR Å Connecting a TV GreenBlue Red Digital input terminals About video signal conversionDigital connection Digital output terminalUSB Connection For USB TerminalConnecting the power cord Selecting the analog or digital input mode Turn on the powerTo turn off the power into standby Basic operationsListening with headphones Adjust the volumeSelecting the digital decode mode To restore the sound, press Muting againSignal and speaker indicators on the display Turning off the power with the Sleep TimerBasic adjustment of auto memory Changing the display brightnessPress SET Basic settingsPress Setting Before you start, rememberBasic setting items Speakers channels number and the sizeRoom size and the speaker distance/output level Setting the surround back speakers-S Back OUT Setting the speakersSetting subwoofer information-SUBWOOFER Turn Multi JOG to select the appropriate settingFrom the remote control Activating the EX/ES/PLIIx setting- EX/ES/PLIIxSetting the speaker distance AutoSetting bass sound Using the Midnight modeSelecting the main or sub channel VCR S/C Memorizing the volume level for each source-ONE Touch OPEDVD S/C OnetouchonSound adjustments Basic adjustment itemsOperating procedure Adjusting the speaker output levels Press Test to check the speakers’ output balanceAdjusting the virtual room size for DSP modes Adjusting the bass soundsAttenuating the input signal-INPUT ATT Adjusting the liveness effect for DSP modesAdjusting the center tone-CENTER Tone To store the preset stations Tuning in to stations manuallyUsing preset tuning Tuner operationsSelecting the FM reception mode To tune in a preset stationIntroducing the Surround modes Creating realistic sound fieldsReproducing theater ambience Dolby Digital3D Headphone mode About other digital signalsDTS All Channel Stereo mode ALL CH Stereo Introducing the DSP modesDigital Acoustic Processor DAP modes About the DSP modes Using the Surround/DSP modesDTSDolby Digital Incoming Signal Type Virtual Surround BackSelecting the Surround/DSP modes When you select Auto SurroundTurn Multi JOG to select the Surround/DSP mode you want Select and play any source other than DVD MultiConnections 2 Video cable connection AV Compu Link remote control systemConnections 1 AV Compu Link connection CaseAutomatic power on/off Connecting procedureAutomatic selection of TV’s input mode One-touch video playChannel + Operating other JVC productsVCR REWRelease DVR/DVD Changing the remote control code for DVD recorderDVD recorder or DVD player TOP MENU/MENURelease TV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Try to operate your TV by pressing TVTry to operate your VCR by pressing VCR Changing the transmittable signals for operating a VCRRelease VCR Manufacturers’ codes for VCRManufacturers’ codes for DBS tuner Release DBS/CATVManufacturers’ codes for Catv converter Try to operate your DVD player by pressing DVR/DVDProblem Possible Cause Solution TroubleshootingPower Remote control TunerFM tuner IHF SpecificationsAmplifier AM tunerPage Page Audio Video Control Receiver RX-D302B Mises en garde, précautions et indications diverses English Parts identification ID Learning 1DVR/DVD Getting started AM antenna connection Connecting the speakers Connecting video components È Ô Red DBS tuner Component video cable not suppliedWhite Video cable not suppliedAbout video signal conversion USB wireless Transmitter supplied Connecting the power cord Basic operations Auto Surr Digital Changing the display brightness Basic settings Basic setting items Setting the speakers Activating the EX/ES/PLIIx setting- EX/ES/PLIIx Dual Mono DBS Video Sound adjustments Adjusting the speaker output levels Adjusting the bass sounds Dimension Tuner operations Selecting the FM reception mode Creating realistic sound fields DTS Introducing the DSP modes Digital When activating NEO6 MUSIC, you can adjust Center RX-D302B Equipment To video input Connecting procedure Operating other JVC products DVD recorder or DVD player Operating other manufacturers’ products English Release DBS/CATV There are any problems you cannot solve, contact your JVC’s Specifications RX-D302B