Weider 831.153933 user manual Trap is turned to hold the Cable in the groove of the Pulley

Page 12

19.Route the Swivel High Cable (74) through the Swivel Upright (5) and over a 4 1/2” Pulley (119). Attach the Pulley inside the Upright with a 3/8” x 2 3/4” Bolt (101), two 3/8” Washers (91), two 1/2” Spacers (89), and a 3/8” Nylon Locknut (87).

Attach a 3/8” x 2 1/2” Bolt (18), two 3/8” Washers (91), and a 3/8” Nylon Locknut (87) to the Swivel Upright (5).

20.Remove the preattached 3 1/2” Pulleys (78) from the Small Pulley Plates (31).

Wrap the Swivel High Cable (74) over a 3 1/2” Pulley (78). Attach the Pulley and a Cable Trap (68) to the second set of holes from the top of the Small Pulley Plates (31) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure the Cable

Trap is turned to hold the Cable in the groove of the Pulley.

21.Wrap the Swivel High Cable (74) over a 4 1/2” Pulley (119). Attach the Pulley inside of the indicat- ed bracket on the Top Frame (6) with 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87).

22.Lift the Weight Tube (43) and the Top Weight (45) closest to the Swivel Upright (5). Make sure that the small pin on the Weight Tube is inside of the groove under the Top Weight.

Insert a Weight Pin (50) into the stack of Weights (44). Place a 1/2” Washer (1) on top of the Weight Tube (43). Tighten a 1/2” Nut (118) halfway onto the end of the Swivel High Cable (74). Screw the end of the Cable two full turns into the Weight Tube. Then, tighten the Nut against the 1/2” Washer.

23.Locate the Swivel Cable (17), which is 115 3/8” long and has an eyelet on each end. Attach the Cable inside the Top Frame (6) with a 5/16” x 2 1/2” Bolt (59), two 5/16” Washers (90), and a 5/16” Nylon Locknut (86).

19

 

 

91

18

 

 

5

 

 

 

 

 

101

 

 

 

 

 

 

91

 

 

 

 

91

87

 

 

 

 

 

 

 

 

 

89

 

 

 

 

 

91

 

 

 

 

 

 

87

89

 

119

 

 

74

 

 

 

 

 

 

20

 

 

 

 

 

 

 

 

 

74

 

 

 

 

 

 

87

 

 

 

 

 

 

 

 

 

100

 

 

 

78

68

31

 

 

 

31

 

 

 

21

 

 

 

 

 

 

 

 

 

 

 

 

6

 

93

 

 

 

 

 

 

 

 

 

 

 

87

 

 

 

119

74

22

 

 

 

 

 

 

 

 

 

 

 

 

74

5

 

 

 

 

 

118

 

 

 

 

 

 

50

 

 

45

 

 

1

 

 

 

 

 

 

 

 

 

 

43

 

 

 

 

 

 

 

 

 

 

 

 

44

23

 

 

59

 

 

 

 

 

 

 

 

86

 

 

 

90

 

 

 

 

 

 

17

 

 

 

 

 

6

12

Image 12
Contents Model No Serial No Sears, Roebuck and Co., Hoffman Estates, ILTable of Contents Important Precautions DecalBefore YOU Begin One on each sideAssembly Frame Assembly Locknut the Squat Knee Rest must be able to pivotLocknuts yet Do not tighten the Nylon Locknuts yetPage Assemble the other weight stack in the same way Open the parts bag labeled ARM Assembly Do not tighten the Locknuts yetCable Assembly Repeat this step with the Left Butterfly ArmTrap is turned to hold the Cable in the groove of the Pulley 100 68 78 101 102 Page Page Page Page Seat Assembly Locate and open the parts bag labeled Seat AssemblyRepeat this step with the other end of the Squat Arm Nylon Locknuts yetTighten all of the 3/8 Nylon Locknuts 87 used in this step Page Adjustments Ing any exerciseAdjusting the Squat ARM or Swivel Carriage Weight Resistance Chart StationTroubleshooting Tightening the CablesCable Diagrams Lat CableButterfly Cable Swivel High Cable Squat Cable Leg Lever Swivel CableSwivel Low Part Identification CHART-Model No R1003APage Page Part LIST-Model No Key Qty DescriptionExploded DRAWING-Model No Full 90-DAY Warranty Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL