Whirlpool W10150626A, W10150627A DryingandCycleTips, StatusLights, Stopping,PausingorRestarting

Page 15

How the AccelerCare™ Drying System Works

Moisture-sensing strips inside the dryer drum and temperature sensors in the airstream monitor how fast the load is drying, how hot the air should be and when clothes are dry. The system automatically stops the cycle to help save time and avoid overdrying.

To use a Timed Cycle

Turn knob to desired Timed Cycle.

Press the TIME ADJUST up or down arrows until the desired drying time is displayed. Press the up or down arrows and the time will change by 1-minute intervals. Press and hold the up or down arrows and the time will change by 5-minute intervals.

NOTE: The Time Adjust features can be used only with Timed Cycles.

Press TEMP until the desired temperature illuminates.

NOTE: The Temp feature can be used only with Timed Cycles.

NOTE: During a Timed Cycle, you can change the settings for Time, Temp, WRINKLE SHIELD™ and the End of Cycle Signal.

5.(OPTIONAL STEP) If desired, select OPTIONS. For more details, see “Options.”

6.(OPTIONAL STEP) If desired, press END OF CYCLE SIGNAL. A signal will sound to alert you when a cycle ends. For more details, see “End of Cycle Signal.”

7.Press START. Be sure the door is closed.

If you do not press Start within 5 minutes of selecting the cycle, the dryer automatically shuts off.

If you wish to end your drying cycle after pressing Start, press PAUSE/CANCEL twice.

DryingandCycleTips

Select the correct cycle and dryness level or temperature for your load. If an Automatic Cycle is running, the display shows the estimated cycle time when your dryer is automatically sensing the dryness level of your load. If a Timed Cycle is running, the display shows the exact number of minutes remaining in the cycle.

Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down depends on the load size and dryness level.

Drying tips

Follow care label directions when they are available.

If desired, add a fabric softener sheet. Follow package instructions.

To reduce wrinkling, remove the load from the dryer as soon as tumbling stops. This is especially important for permanent press, knits and synthetic fabrics.

Avoid drying heavy work clothes together with lighter fabrics. This could cause overdrying of lighter fabrics and lead to increased shrinkage or wrinkling.

Cycle tips

Dry most loads using the preset cycle settings.

Refer to the Automatic or Timed Preset Cycle Settings chart (in the “Cycles” section) for a guide to drying various loads.

Drying temperature and dryness level are preset when you choose an Automatic Cycle. You can select a different dryness level, depending on your load, by pressing Dryness and choosing More, Normal, Less or Damp.

NOTE: You cannot use the Time Adjust and you cannot choose a Temperature with the Automatic Cycles.

If you wish to adjust the cycle length of a Timed Cycle, press the Time Adjust up or down arrows. Adjust the temperature of a Timed Cycle by pressing Temp until the desired temperature is selected.

NOTE: You cannot choose a dryness level with Timed Cycles.

StatusLights

Follow the progress of your dryer with the drying Status indicator lights.

Stopping,PausingorRestarting

To stop or pause your dryer at any time

Open the door or press PAUSE/CANCEL once. Press PAUSE/ CANCEL twice to cancel a cycle.

To restart the dryer

Close the door. Press START until dryer starts.

NOTE: Drying will continue from where the cycle was interrupted if you close the door and press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will shut off.

Select new cycle settings before restarting the dryer.

Sensing

In an Automatic Cycle, the Sensing light illuminates until a wet item is detected.

In a Timed Cycle, the Sensing light illuminates at the beginning of a cycle and turns off 5 minutes into the cycle.

Wet

The Wet light illuminates at the beginning of an Automatic Cycle if a wet item is detected.

In an Automatic Cycle, if a wet item is not detected after approximately 5 minutes, the dryer goes directly into Cool Down and the Cool Down and the WRINKLE SHIELD™ setting indicators illuminate, if selected.

In a Timed Cycle, wet items are not detected. The dryer will continue to run for the length of time selected, and the Wet light will illuminate. The damp light will not illuminate.

15

Image 15
Contents W10150626A Cabrio Fabric Care System GAS DryerTable DES Matières Your safety and the safety of others are very important Dryer SafetyImportant Safety Instructions Installation Instructions ToolsandPartsLocationRequirements Electrical Requirements Mobile home installations requireMobile home Additional installation requirements Dryer DimensionsGas supply connection requirements GasSupplyRequirementsGas Type Gas Supply LineDryer Gas Pipe If using an existing vent systemVentingRequirements Burner Input RequirementsSpecial provisions for mobile home installations PlanVentSystemExhaust Determine vent path Install VentSystemInstall LevelingLegs Vent system chartMakeGasConnection ConnectVentLevelDryer Reverse the strike Remove the door assemblyReinstall the door ReverseDoorSwingIf the dryer will not start, check the following CompleteInstallationTo make changes during an Automatic Cycle Dryer USEStartingYourDryer To use an Automatic CycleStopping,PausingorRestarting DryingandCycleTipsStatusLights Cycles Modifiers Options EndofCycleSignal ChangingCycles,Modifiers andOptionsDryingRackOption Dryer Care CleaningtheDryer LocationCleaningtheLintScreen CleaningtheDryerInteriorDryerOperation TroubleshootingVacationandMovingCare ChangingtheDrumLightDryerResults Accessories IntheU.S.AInCanada Call Whirlpool Corporation Major Appliance WarrantyVotre sécurité et celle des autres est très importante Sécurité DE LA SécheuseImportantes Instructions DE Sécurité Instructions D’INSTALLATION Exigences d’emplacementOutillageetpièces Dimensions de la sécheuse Linstallation dans une maison mobile exigeSpécifications électriques Exigences concernant le raccordement au gaz AlimentationengazType de gaz Canalisation d’arrivée de gazExigencesconcernantlévacuation Canalisation d’arrivée de gaz de la sécheuseEn cas dutilisation du système dévacuation existant Évacuation Planificationdusystèmed’évacuationTableau des systèmes dévacuation Déterminer litinéraire dacheminement du conduitPour utilisation dans une maison mobile Installationdusystèmed’évacuationInstallationdespiedsdenivellement RaccordementaugazDépose de la porte Raccordementduconduitd’évacuationRéglagedelaplombdelasécheuse Inversiondusens douverturedela porteInversion de la gâche Réinstallation de la porteSi la sécheuse ne démarre pas, vérifier ce qui suit Acheverl’installationUtilisation DE LA Sécheuse MiseenmarchedelasécheuseUtilisation dun programme automatique Conseils pourleséchageetles programmes Arrêt,pauseouremiseenmarcheProgrammes Témoins lumineuxModificateurs Signaldefindeprogramme Utilisation de la grille de séchage OptiondegrilledeséchageChangement des programmes après avoir appuyé sur Start Modification des préréglages de niveau de séchageNettoyage avant chaque charge NettoyagedelemplacementdelasécheuseEntretien DE LA Sécheuse NettoyagedufiltreàcharpieChangementdel’ampouled’éclairagedutambour Nettoyagedel’intérieurdelasécheuseRetraitdelacharpieaccumulée DéménagementDépannage FonctionnementdelasécheuseRésultatsdelasécheuse Charges avec faux plis Temps de programme trop courtCharpie sur la charge Taches sur la charge ou sur le tambourAccessoires Si vous avez besoin de pièces de rechangePour plus d’assistance Garantie Limitée DE UN AN Garantie DES Gros Appareils Ménagers Whirlpool CorporationWhirlpool Corporation All rights reserved W10150626A SP PN W10150627A