Miele PW 5065 manual Symbols, Special features in the program sequence Anti-crease

Page 23

Program sequence

Symbols

d= Low water level

( = Medium water level e = High water level

a= Normal wash rhythm b = Gentle wash cycle c = Woolens

The washer is equipped with an electronic control which determines the load size automatically. The washer determines the required water consumption for each load and water absorbency of the laundry. Different program sequences and wash times will result.

The program sequence shown in the chart represents the basic program with a maximum load. Possible "Options" are not considered.

The washer’s program sequence display will indicate the current step of the selected wash program.

Special features in the program sequence:

Anti-crease:

The drum continues to turn up to 30 minutes after the program has ended to prevent wrinkling. The washer can be opened at any time. Exception: The program "WOOLLENS" has no anti-crease feature.

1)Pre-rinse

To rinse excess soiling, a pre-rinse without detergent is automatically added to the program.

2)High Spin

Before the wash program starts, a high spin is carried out to remove the air from the pillows. After the spin the program starts with the water intake.

3)In the "Outerwear" program the items will be spun only after the main wash.

4)In the program "Flour +" a third rinse is added.

23

Image 23

Contents Operating manual Washer Contents Technical Safety Important Safety InstructionsUse Children Using accessoriesDoor button Guide to the washerControl panel Display with -, OK and + buttonsOK button Temperature conversions Celsius FahrenheitDisplay + buttonsFirst wash Before using for the first timeSetting time of day Reminder of the shipping strutsGeneral tips Using the washerSort the laundry Close the drum door Load the laundryPre-wash Delay StartSelect a program Too much detergent may cause Adding detergentToo little detergent may cause Remove the laundry Starting a programAt the end of a program Coin mechanismChanging a program Canceling a programAdjusting the temperature Adjusting the spin speedDrum door cannot be opened if Adding/removing laundry during a wash programProgram guide Dark garments 40C to cold 104C to cold Bed linen 60C to 40C 140F to 104FCurtains 40C to cold 104C to cold Denim 40C to cold 104C to coldPillows 95C to 40C 203F to 104F Special programs Quick wash 40C 104FShirts 60C to 40C 140F to 104F StarchExtra Rinse Proofing 40C to 30C 104F to 86FDo not use agents containing paraffin Towels short 40C 104F Intensive Wash 60C to 40C 140F to 104FFlour 95C to 40C 203F to 104F Grease and fat 95C to 40C 203F to 104FHygiene Towels + 60C to 40C 140F to 104FCapes 30C 86F Chem. Therm. Dis min 60C 140FMain wash Rinse Spin Program sequenceSpecial features in the program sequence Anti-crease SymbolsSelecting a spin speed Changing the delay start Delay StartSetting the delay start Starting the delay startNormal soiling DetergentWater hardness Water softenerDye removers / Fabric dyes Fabric softener, liquid starchCleaning the detergent drawer Cleaning and CareCleaning the washer Cleaning the filter in the inlet valve Cleaning the inlet hose filterCleaning the inlet hose filters Wash program cannot be started Frequently asked questionsDisplay message Possible cause Solution Display shows a fault messageGeneral problems with the washer Poor wash results Door will not open when the Door button is pressed Machines with a drain pump Remove the toolOpen the lint trap door Open the drum door Remove the lint trap lidMachines with a drain valve Changing the light bulb Repairs After sales servicePC Update Optional accessoriesPage Installation Instructions Front view InstallationRear view Do not lift the washer by the drum door Installation siteInstallation Removing the shipping strutsPull the shipping strut out Pull out the shipping strut out InstallationInstalling the shipping struts Leveling the washer Height Washer/ Dryer Stack Installation on a baseReinstallation of the machine lid Coin mechanismExtension hoses MaintenanceWater connection Cold water connectionHot water connection Drain pump DrainageDrain valve Electrical connection Technical Data Disposal of an old appliance Help to protect the environmentDisposal of the packing materials Menu Settings J To adjust standard settings Language J Settings JAccessing the Settings J Leaving the Settings menuSelecting the clock display Time of dayDisplay contrast Display brightnessMemory Not in current prog. factory defaultStandby Entering the code Menu Settings Supervisor levelMain wash water Supervisor levelAuto load control Minimum Iron water level Rinse waterLow Water Pressure Cottons water levelCottons rinses Minimum Iron durationSpecial programs list Pre-washPre-rinse Cottons Leaving the Settings menuMinimum Iron rinses External dosageAlteration rights reserved