Miele PW 5065 manual Water connection, Cold water connection, Maintenance, Extension hoses

Page 49

Installation

Water connection

Cold water connection

A water faucet with 3/4" threat must be provided on-site. If none is available the machine must be connected to a water line by a qualified plumber.

The water pressure must be between

14.5-145 psi (1 -10 bar). If the water pressure is greater than 145 psi

(10 bar), a pressure reducer must be installed. If the water pressure is below 15 psi (1 bar), there will not be enough water available for a complete fill.

The cold water hose (blue mark) is not suitable for a hot water connection.

^Connect the cold water intake hose (blue mark) to the cold water valve.

^Turn on the valve(s) and check for leaks.

The water intake hoses are equipped with screen filters. Do not remove these filters except for cleaning.

Maintenance

Replace the water hoses only with genuine Miele hoses.

Extension hoses

Extension hoses (8’ 2" or 13’ [2.5 m or 4 m]) may be obtained from Miele.

49

Image 49
Contents Operating manual Washer Contents Technical Safety Important Safety InstructionsUse Children Using accessoriesControl panel Guide to the washerDisplay with -, OK and + buttons Door buttonDisplay Temperature conversions Celsius Fahrenheit+ buttons OK buttonSetting time of day Before using for the first timeReminder of the shipping struts First washSort the laundry Using the washerGeneral tips Close the drum door Load the laundrySelect a program Delay StartPre-wash Too little detergent may cause Adding detergentToo much detergent may cause At the end of a program Starting a programCoin mechanism Remove the laundryAdjusting the temperature Canceling a programAdjusting the spin speed Changing a programDrum door cannot be opened if Adding/removing laundry during a wash programProgram guide Curtains 40C to cold 104C to cold Bed linen 60C to 40C 140F to 104FDenim 40C to cold 104C to cold Dark garments 40C to cold 104C to coldShirts 60C to 40C 140F to 104F Special programs Quick wash 40C 104FStarch Pillows 95C to 40C 203F to 104FDo not use agents containing paraffin Proofing 40C to 30C 104F to 86FExtra Rinse Flour 95C to 40C 203F to 104F Intensive Wash 60C to 40C 140F to 104FGrease and fat 95C to 40C 203F to 104F Towels short 40C 104FCapes 30C 86F Towels + 60C to 40C 140F to 104FChem. Therm. Dis min 60C 140F HygieneMain wash Rinse Spin Program sequenceSpecial features in the program sequence Anti-crease SymbolsSelecting a spin speed Setting the delay start Delay StartStarting the delay start Changing the delay startWater hardness DetergentWater softener Normal soilingDye removers / Fabric dyes Fabric softener, liquid starchCleaning the washer Cleaning and CareCleaning the detergent drawer Cleaning the inlet hose filters Cleaning the inlet hose filterCleaning the filter in the inlet valve Wash program cannot be started Frequently asked questionsDisplay message Possible cause Solution Display shows a fault messageGeneral problems with the washer Poor wash results Door will not open when the Door button is pressed Open the lint trap door Remove the toolMachines with a drain pump Open the drum door Remove the lint trap lidMachines with a drain valve Changing the light bulb PC Update After sales serviceOptional accessories RepairsPage Installation Instructions Front view InstallationRear view Installation Installation siteRemoving the shipping struts Do not lift the washer by the drum doorPull the shipping strut out Pull out the shipping strut out InstallationInstalling the shipping struts Leveling the washer Reinstallation of the machine lid Washer/ Dryer Stack Installation on a baseCoin mechanism HeightWater connection MaintenanceCold water connection Extension hosesHot water connection Drain valve DrainageDrain pump Electrical connection Technical Data Disposal of the packing materials Help to protect the environmentDisposal of an old appliance Menu Settings J To adjust standard settings Accessing the Settings J Settings JLeaving the Settings menu Language JDisplay contrast Time of dayDisplay brightness Selecting the clock displayStandby Not in current prog. factory defaultMemory Entering the code Menu Settings Supervisor levelAuto load control Supervisor levelMain wash water Low Water Pressure Rinse waterCottons water level Minimum Iron water levelSpecial programs list Minimum Iron durationPre-wash Cottons rinsesMinimum Iron rinses Leaving the Settings menuExternal dosage Pre-rinse CottonsAlteration rights reserved